The Elegant Elna Air Electronic TSP Sewing Machine - Basics

[@theprofessor9163]

What a fantastic guide. So clear, unambiguous, and to the point. If only all video makers were like you.

[@bethanykafer1276]

I'm so glad i found this video. I was given my grandmother's sewing machine as well as her sewing table. This was so helpful for me as I found it hard to figure it out with the manual, because im a visual learner. Very informative!

[@patticrane]

Sir, what a fabulous, useful video you made for all us diehard vintage Elna fans! My Elna Air Electronic turned FORTY on Christmas Day, and when I brought it out of retirement to make masks for the pandemic, I fell in love with sewing all over again after too many years away as a traveling executive. I had forgotten some of the details you so carefully and elegantly demonstrated. Thanks to you, now I will get even better use out of my sweet Elna than I did before...and realize that other than self-threading needles and self-snipping threads, those lightweight modern machine have little to offer that my Elna cannot already perform so well. Thank you for your dedication to care and craftsmanship. Patti Crane, Los Angeles

[@InStitches]

Thank you for your kind comment.

[@sophiemartinwelsh]

I have been gifted my friends grandmothers machine and never seen one like it before. This video was perfect! Thank you!

[@mariamciver8401]

My mum bought this very machine for me, only 1 year old, in 1984 for $800 Australian dollars. It was a LOT of money back then, and hard earned. We have both used it to death, and have ever only serviced it 3 times in 36 years. It is a beast, and is still going flawlessly! Would never part with this one! Great video, thank you!

[@InStitches]

Yes, expensive but as you'll know, made to last generations which makes it worth while in the long run. Don't get me started on today's throw away society :)

[@k6kwi]

Good morning… my wife has an Elna Air Electronic. As you demonstrated it works by air pressure from the foot control. However it seems to be losing pressure after an about 10- 15 seconds. We replaced the foot control with the line up to the machine. It did not resolve the issue. Hers the irony, Although we are in California, this machine traveled to NZ and back in the late 1980s where I am from before we moved to CA 😊. Any clue on what the problem might be would be greatly appreciated!! Many thanks.

[@gladysma308]

Very good video - 6:00 minute bobbin 26:00 button holes 29:00 darning foot

[@mrn6020]

Wow thank you!! Just found a Elna Jubile in the thrift store for 5 euro :). I’m a beginner and just did my first sewing. Thanks to you! Great tutorial, will open it tomorrow to oil it a bit.

[@prettygirl1912]

This was so so so helpful!! I’m using my husband’s late grandmothers machine and all of the instructions were in Dutch so it was a bit difficult. I really appreciate you making this video! 😊🪡

[@InStitches]

You are so welcome!

[@TheresaArendseArendse]

Hi how do you put bobin back in place pls. I end up with 3 different peaces in my hand. Pls help

[@kerrykennedy2192]

I bought my machine new in the 70s. I can't find my manuals (packed away in some boxes of books) and needed to oil and clean the machine after some time of disuse. Your video was just what I needed. I watched almost the whole thing to remind me of how to use all the stitches. This machine is wonderful. I can't believe how dependable it has been over the years. I made tailored jackets and coats, Halloween costumes, drapes. I think I only paid about $500 for it, which was certainly a bargain considering all the years it has served me.

[@pennyenicks7905]

I inherited an Elna with no manual. Your video has been a Godsend and I love my machine. Thank you!

[@InStitches]

Great! I'm pleased it was helpful.

[@martaroller835]

My mother bought this machine for me years ago but I haven't been able to find a manual so I was so happy to find your video. It was really helpful for me to see the close-up of how you thread the bobbin with the piece removed from the machine. Thank you!!

[@InStitches]

Thanks. Glad to hear you got your machine working well again.

[@petercane6376]

Excellent in depth video covering just about everything. Brilliant demo about how the bobbin thread goes between the two fingered sprung lever. You were not shy of the button hole and I am thankful for that. I just bought mine today and was hoping for a button hole demo with this machine. What a fantastic solid beautifully built little beauty. Knocks the socks off any Singer 221 Featherweight which are grossly overpriced . For a small portable machine this cannot be beaten. Easily level pegging with Bernina. ( Old metal ones) Both machines are built like Rolls Royces. Thanks for the Vid. What a little pearler!

[@wirdy1]

Recently gumtree purchase & your video has really helped me. Now fully serviced it & sews lovely. You can just feel & hear the quality. So much time & effort has been put into your editing, it so so easy to watch. Thank you.

[@maggiewright6908]

I have had problems with the Elna servicing in France, my TSP and Lotus are both catching the underneath thread - your video has sorted out the problem, and the simple way you explain is just wonderful. I do hope you get this message, as both machines have travelled all over the world with me.

[@InStitches]

Thank you. I'm pleased this helped you out.

[@tpot2003]

I just got my Mom's Elna. Your video is the best!! She recently passed away and never showed me how this machine or her new Brother were threaded. Thank you so much for recording this. :)

[@InStitches]

Thanks. I'm pleased it helped.

[@purplecrazymoo]

I've inherited one of these lovely sewing machines and I was looking for a video on how to do free motion sewing - so thank you so much!

[@Hesfordillman]

That was a brilliant crash course in how to use this machine. Now im of to make a bed cover. Thanks

[@BuPaKn]

Thnx for the video! It was very very helpful. I just bought one from a private individual that hasn’t used it at all because she once got it from someone. I just tried all the stitches but there seem to be a problem with the stitch width. But luckily I’ve found also your video about fixing the zigzag issue..🤩 Gonna try to fix it tomorrow! Thousand times thanks 🙏🏻

[@johnmontgomerie7286]

Wow Excellent demo, you have given me confidence to try this sewing, I was given same machine and was going to donate to charity, but now I will learn to drive it and do some sewing for charity. Many thanks for this wonderful video.😀👍

[@InStitches]

Good on you!

[@KarenEBlackburn]

This was sooo helpful. I inherited my mum's Elna Air Electronic SU many years ago and have been using it off and on, but only learnt what I know from watching her use it. NOW I know how to use all the bits and pieces and what they are for. I never knew about the tension thingy on the bobbin - that explains a lot!

[@InStitches]

Glad it was helpful!

[@BethandSarahRDQS]

Thank you for your very informative video. Keep sharing!

[@robinr6399]

If you have a hole in the leftside spoolpin, you may try putting the spool on the rightside pin and threading through that hole on the leftside pin. That may keep the spool from dancing too much and flying off. Great video! Such clear camera work! Thank you😊

[@timflanigan8586]

Just got this machine in an estate sale. Had everything figured out except for the bobbin extractor… as soon as I saw you use that, my honest reaction was “Get the F outa here!” Thanks for posting!!!!

[@InStitches]

Thanks.

[@danl6558]

Sooo good video. I have an Elna Carina Electronic. Now I finally fully understand it

[@deriquecoetzee4099]

Thank you very much! I inherited a tx (t sp) from my Mom and this video helped a lot with the basics. I'm just starting out :-)

[@InStitches]

Glad it was helpful!

[@latinjazz07]

Merci beaucoup pour toutes ces explications ! thank you so much ! you've made my day. I've just bought one of these, the same as I probably used when I was a schoolgirl but without guide. Warmest wishes from Switzerland

[@InStitches]

Nice to hear. Thanks.

[@jodihendrickson1795]

Gosh you do a great demo! I found a clean vintage Elna 500 complete with the attachments and owners manual. Although I change the lightbulb without using the handy-dandy push down hole and a few bad words slipped out in the process. 😬 Thank you!

[@marieer8810]

Thank you so much for this useful video! Finally I understand how my great-granny`s sew machine works! Best regards from Germany :)

[@InStitches]

Thanks. I'm pleased it was helpful.

[@MaA-th1hy]

I have my Elna Air Electronic TSP Sewing Machine since 2081, given as a gift from my late mother. What a lovely machine. Unfortunately the engine burnt our, but I was very lucky to find a second hand TSP sewing machine. I love my TSP and it has never let me down. Thank you for the video.

[@Mabrownfl]

Great video. Very clear and concise.

[@michellebarney9384]

Hi there, is there anyway you can make another video explaining how to lock in the last stitch and how to remove the stitched fabric from the machine. I can't seem to figure this out. Thank you so much!

[@margaritaklase4989]

So thankful for this video. It's been years I haven't been able to make a good buttonhole with my Elna Air Electronic SU sewing machine which I bought at an estate sale years ago even though it included the instruction book and manual. So many other features I'd like to learn which seem to be on this video. I only forwarded to the buttonhole part so I could finish my project but can't wait to watch the whole video. I am currently trying to find a walker foot that would fit and ordered one from Sewing Parts, hopefully is compatible.

[@verotte]

thanks a lot for these explanations I had trouble with bobin .....

[@tapslagata]

Best tutorial video I’ve ever seen. Thank you!!

[@InStitches]

Glad it was helpful!

[@vadim730]

Best video for sewing basics I've ever seen very nice hob thanks

[@InStitches]

Glad it was helpful!

[@missb1779]

Hi, I'm the one who asked u abt bernina 830 record a few days ago. I returned the bernina 830 due to a possible motor issue and I got myself a Elna Air Electronic SU instead. It is a blue and white machine. I want to thank you for your detailed videos, thanks to you I got to know about Elna machines, that was why I decided to get the Elna instead, bcos it looks so retro and cute and yet functional. Everything works fine, the stitches are great, the cams work well, but the machine sounds like a mini typewriter. Folks in the Elna group say that it should be quiet, it should be purring but mine isn't. The noise is exactly the same as yours. So I shouldn't be worried if it is too noisy? I opened up the bobbin plate and the top part of the machine and see that it is oiled nearly everywhere. It is definitely noisier than my plastic brother Innovis machine. Hope to hear your opinion on this. Thank you.

[@peterbryenton]

Useful information, thank you.

[@tapslagata]

Thank you soooo much! I just got blessed with an Elna Jubile and I love it!!

[@InStitches]

You are so welcome!

[@andersberg1987]

Thank you so much for this great video!

[@markrobirds7984]

I recently came into a SU 68 and have gone through most everything on it cleaning and oiling including the entire bottom end. While I went to test stitching I noticed the needle clamped in with an angle instead of a true front to back orientation. The needle clamp is positioned just as I would expect it to be but the slot in the needle bar is not directly in the center and this has the needle rotated about 5 degrees or so clockwise from the top down view. I had the impression that the needle bar had gotten out of rotation and that someone had previously rotated the clamp to be straight rather than the needle bar itself which seemed odd. I'm looking at this video at the 12:52 mark and this needle bar looks like what mine has going on. I also notice the exact same situation on the Jubile video. Are these Elnas actually designed that way? Though the bobbin is off center the hook shuttle is on center line with the needle and would make me think that the needle should be aligned to a true front to rear orientation. Can anyone verify either way before I reorient this one and the clamp? I'd rather not have to undo my "fix" if it is not correct. Have been unable to find an available service manual that's downloadable yet.

[@pookiebear9200]

Thanks for your great videos! I have an similar machine a Elna SU air electric. I have cleaned underneath but not sure if it is ok to put a bit of Triflo synthetic grease on the gear? Thanks!

[@GM-jp4mv]

Excellent tutorial. Have you ever needed to glue the bushing on the wheel of Elna AE SU? My machine is not always connecting and I was told it could be this. Also only works on fast mode. Thanks

[@nadinedinc8906]

This was a great video! I just bought an Elna Electronic TSP without any manual so this has been sooooo helpful - my sewing can finally begin!

[@InStitches]

Glad it was helpful!

[@dianarutecki9810]

I have the Elna Su air electronic . Love it

[@InStitches]

Yes, they are very nice machines.

[@rosannekoekkoek6663]

Very useful! I am wondering if this machine has an option to adjust the pressure foot tension. My fabric is being fed unevenly and I'm trying to find a solution.. Any tips?

[@dennisclapp7527]

Thank you. That was a well done tour of the TSP. I am wondering if the bottom front piece that you call a stabilizer would also be necessarily pulled out to use the free arm feature. Please keep posting these highly informative videos. They are appreciated.

[@praviniabluck3847]

Great video tutorial re Elna Air Electronic. I purchased my SU model in 1979 and she still goes great. One question I do have is I only thought there was one red mark in the bobbin area to oil but you pointed out there are several points that need oilding including when you removed the top of the machine. Do you have a video of where else I need to oil or would I need to take it to a sewing machine repair shop? Also I have had my under stitching unravel and found I needed to turn the tension dial (which was always on 4) to between 5 & 6. Still not perfect but works better. Would you know why the tension has changed after all these years by any chance? From New Zealand 8-)

[@InStitches]

Thanks. As far as oiling goes, you can download the manual here - www.manualslib.com/download/378226/Elna-Tsp-Air-Electronic.html. Also take a look at this video which may explain tension issue. kzbin.info/www/bejne/j4ashXeFZ8Rsqc0 - There's also a part 2 here - kzbin.info/www/bejne/aamTe2qDbtqeqNE

[@praviniabluck3847]

@@InStitches Thank you for your reply. My husband followed your video instructions and cleaned out some lint in the tension wheel and modified the white plastic knob you spoke about which was about 6.5 mm and so he dropped it down to your recommended measurement. The machine is stitching much better so another big thank you for all your help. Just one more thing, how and where is the manual you mentioned in your email so I can oil the other parts of the machine please? Regards, Pravinia

[@praviniabluck3847]

Oops, I didn't scroll down enough and just realised you had given me the link for the manual!

[@praviniabluck3847]

Sorry to bother you again! I was sewing away very happily when I noticed that the thread from the top downwards was almost falling out from each area that I threaded it (from the hook that goes up and down,) it even came out if the needle at one point! Seems my stitches are not stitching a nice straight stitch but slightly slanted! I'm almost thinking I'm going to have to take it to a sewing machine mechanic. Would you perhaps have any further helpful tips why this may be happening please? My husband thought he might have lowered the white tension release bolt in the top of the machine may have lowered it too much and not the 5.5mm you recommended? Would it pay to go over this step again? Many thanks in advance.

[@jonnafry]

Great information! Quick question ... how to access the air control module from end. Can't see any screws apart from the rubber foot underneath and I don't want to get medieval on it quite yet. Cheers.

[@InStitches]

Hi. Remove the lid and there are two screws holding the end cover on. Thanks.

[@jonnafry]

Much appreciated and thanks for such a prompt reply. That information will save numerous experimental plastic marring. Cheers. @@InStitches

[@jonnafry]

Just a follow up in case it's of value to anyone ... the original problem was with the machine sometimes remaining running despite taking your foot off the controller. It had been taken to a service centre but the problem returned a few days later. On examination of the air actuator, the guide rod didn't move nicely in the guide hole and the hole was slightly oval and impregnated with carbon dust which enabled the rod to rack and lock despite oiling. Removing 1/10mm off the diameter returned it to round and removed the 'gritty' feel and a tiny application of ptfe grease gave it a nice feel when depressing the speed pins. So far so good but like all repairs, time will be the ultimate judge. Thanks again for you help. (ps you probably are already aware but I had to remove the power spec. badge to access the screws to gain access to the actuator. @@InStitches

[@QBurgOnline]

THX! Very helpful, if one uses the machine for the first time!

[@MuneeraMahmood-x3q]

I had never tried the -S+ on my Elna SU Air Electronic machine until I saw this video. As you know, t is on the stitch length selector after the reverse stitch selector; much to my surprise the stretch stitch ONLY sews in reverse. I do not have the buttonhole selected. on any dial. I am not sure what is going on. Can you please help?

[@LauraVillafuerte-f1b]

Thank you for your video

[@gladysma308]

I have learned a lot from this video, Thank you very much. Please make a video how to clean, maintain, oiling Elna tx electronic model.

[@InStitches]

Good to hear you learned a lot from it. I'm not sure if I have a tx model but I'll keep en eye out.

[@songvector]

Thank you so much!! Your video was supremely helpful. You are greatly appreciated. :-)))))

[@InStitches]

Glad it was helpful!

[@animalista_fabrics]

so cute helper!)

[@elizenolte4687]

Great video. My Elna air carina SU is getting very slow. The foot control appears intact, but to get it to speed up, I remove the pipe from the machine and then plug it in again. Could it be that the internal mechanism is leaking air?

[@InStitches]

Hi. Yes, probably a leak from the foot controller bellows, the lead or the small diaphragm inside the machine. Thanks.

[@imikhonto]

Hi. There are other feet that you haven’t demonstrated … I’m not sure what the they for. It has a white plastic plate on the left which can be adjusted for thickness of fabric.

[@gladysma308]

Thank you for your detailed explanation. I am a newbie to Elna tx electronic. Please advise why a tangle of thread usually shows on bottom when using reverse stitches, and how to fix to avoid such clustering.

[@InStitches]

It sounds like your top tension may be too loose?

[@adrilezar5203]

Goodday. Is the manual hand wheel quite tight or is it loose? And if it's suppose to be loose what could caus3 it to be tight?

[@nicolaarmstrong2865]

I really love your videos! I have just purchased an Elna Carina but it seems to have a problem...when I press the foot control nothing happens ... mostly....I can feel air come out of the tube end and I even tried using another functioning control from my other machine and it doesn’t work with that either. It did work once for a second or two moving the needle up and down and then stopped. I’ve been searching on the web and can’t find any help. It seems to me that there may be an issue with something within the end panel of the machine but I am a novice. Could you help me take my next steps in solving the problem please? Thank you 🙏

[@InStitches]

It's more than likely a leaking air reservoir in the side panel of the machine and I don't think that part is available any more. It could also be a leaking foot controller and those are replaceable. Thanks.

[@hudadari1172]

Very useful video, could you please explain to me how can I repair my machine, its an elna SU, it's doesn't make button holes or zigzag.

[@InStitches]

Thanks. Try this video here - kzbin.info/www/bejne/pai6iWOin7Sqg68

[@vivianl.peoples2652]

Thank you for taking the time to illustrate the TSP machine which is very simular to my SU. The problem I'm having is the top thread keep breaking and I don't know what to do. Can you please help?

[@InStitches]

If you haven't already done so, replace the needle with a good quality new one. Rethread the machine, both bobbin and top thread. Make sure top tension is not too tight or too loose.

[@arrowheadrox]

I just picked up a complete TSP and I had it sewing and cleaned and oiled it. It's still working but I for the life of me cannot get the needle to pick up the bobbin thread this time... Ugh. But your video is wonderful...

[@InStitches]

Make sure to change your needle with a brand new one. Timing may be out? This sounds stupid but make sure you are turning the hand wheel in operating direction. Thanks.

[@PetronellavuyoPhillips]

Thank you so much sir ifd lirn a Lot from you

[@drupadmehta8665]

Very good information thank you very much. I need more help if you can help me out.

[@louisvanzyl1957]

Great video, I threaded machine as shown and also the bobbin but for some reason my needle doesn't pick up bobbin thread. Any advice?

[@InStitches]

Make sure you have a brand new needle in. Maybe the timing is out or the hook pinion gear is broken?

[@linonadia2839]

Hello. I have just bought an old elna SP is it the same as TSP?. Thank you

[@uzettem6964]

Fantastic video. Thankyou. I have the same one. I am trying to sew leather. Any hints please?

[@InStitches]

Make sure you are using a leather needle as they are designed to cut the leather instead of punching holes. Also if the leather is relatively thick you may see small loops on the under side of the seam. This means the top tension is too loose. Tighten the top tension until the loops disappear.

[@mapster72map75]

I just bought an Elna 8000 on EBay, I’m having it serviced right now to get ready for use. I’m looking for some videos to help me learn the stitches and help me keep it maintained.

[@InStitches]

The 8000 is a nice model.

[@mapster72map75]

In Stitches Thanks! I borrowed a friend’s Elna machine ( I think an SC) and it was so smooth and easy to use, that when I found one in my price range, i had to jump. Luckily I have the manual, but I really wish l could learn more.

[@andreamaxwell7538]

Can you buy a roll foot attachment for these old girls? I have my Nan’s Elna Jubilee

[@danamckenzie65]

My machine is the air electronic SU and the tension is only good on 0 Any higher and it starts to gather my fabric I’ve cleaned, rethreaded both top thread and bobbin, new needle, different thread, tried both under and over tension plate centre and altered bobbin tension all to no avail. If you have any clue why the upper thread tension works best at zero I’d be grateful Your Australian 🇦🇺 neighbour

[@kathyrobertson4521]

This was the best video I have seen. Thank you. I have an Elna Air Electronic SU that was my grandmothers and I am having a great deal of difficulty with The Bobbin thread wrapping around the bobbin holder tangling and breaking off. I am using Elna bobbins, making sure my bobbin is in place correctly and in the tension forks. My upper thread is threaded correctly. So now what I am at a loss. I would love to contact you for any suggestions as I am in a remote location. Thank you for any help

[@InStitches]

Than you for the kind words. Are you sure it's the bobbin thread catching? Try different colour threads top and bottom to confirm.

[@kathyrobertson2458]

I will try that. Thank you. If it is the upper thread. What do I need to do?

[@garyhucker8314]

@@kathyrobertson2458 Make sure the top thread is following the path as shown in the manual. Also make sure the thread goes between the tension disks properly and that there is no lint jammed in between the disks. Also make sure the tension is set to about 5. Replace the needle with a brand new one.

[@kathyrobertson4521]

@@kathyrobertson2458 I have figured out the problem and have it working, but this is my question. On the top thread tension that the thread goes around there is a disk. You mention it in your video. I have never worried whether the thread is above or below this disk. If I have it above the disk the tension works and everything is fine. If it is below the disk, it bunches up. So what do I need to know about this tension area that I am missing?

[@InStitches]

That would indicate there's something like lint between the middle and lower disk that's keeping it from clamping the thread. With the presser foot raised, get a torch and something like tweezers to get in between the disks and clean in between them. It's also possible there is a groove worn in the disks from a lot of use. That's more difficult to sort.

[@bluetuber501]

I was given one of these Elnas recently. Sadly, without a power foot pedal; only the air pump and it goes without saying, without a manual. What does the air "pump" (only thing it came with) do? Know of any groups that offer a no-cost or low-cost pdf manual for this machine? Thanks in advance.

[@InStitches]

Hi. The air pump is the foot controller and you just need a power cable. If you email me, I can send you the manuals for free. I also have the power cords available. My email address can be found on my website www.institches.co.nz - Thanks.

[@danamckenzie65]

@@InStitches❤

[@silviebaud-lerjen8383]

Hello! Thank you so much for all those clear explanations, I'v just received the same Elna TSP from my mother-in-law who got it 40 years ago and rarely used it :) It is like new! But the machine has a problem with the tension on the top thread. The top thread can be seen (comes through the tissu) on the underside of the tissu when sewing. I'm pretty sure that the top thread is not held tight enough in the tensioner on the top left of the machine. Actually, when I pull the thread going around the tensioner with my hand, there is no resistance at all. I have tried to open the top cover of the machine to see if I can modify the tension from inside, but the stays hocked on the handle and I can't unscrew the screws of the handle... Do you have another video of how to open the machine? Do you have any idea how I can modify the tension on that tensioner? Thank you sooooo much for your help, from Switzerland, land of Elna and Bernina :)

[@InStitches]

Thanks. When testing the top tension, make sure the presser foot is in the down position. Make sure the tension disks are clean and nothing is caught between them. To remove the cover, you will need to remove the small clip on the handle hinge and slide the handle off.

[@cecileguarinoni8874]

Hi ! Thanks for this, very helpfull! Im looking for new foots for the exact same machine but it seems very difficult to find somes... Could you help me for the reference maybe? because i'm not sure that the universal foot fits. Thank you in advance :)

[@InStitches]

Thanks. You should be able to find feet online. They are not generic snap on feet.

[@philipdutoit485]

Sir, I REALLY need your advice on this machine. I took it in for a service, and since then, my straight stitch is wavy and uneven. Not like it used to be at all. Tried all recommendations I can find, but maybe it's something specific to this model that you could advise? I changed the threads, new needle, even re-aligned the feed dogs. None of it seems to help the straight stitch remain perfectly straight.

[@InStitches]

Maybe take it back to your service person? It could be a tension issue? I assume you've made sure it's set to straight on the dials?

[@shelbywatts2480]

This is a great video. When were these machines manufactured? I purchased a used one recently and the metal plate with Model No. and Serial No. had been removed. Weird. Now I'm wondering about the history of my specific machine. Thank you.

[@InStitches]

As far as I know they were manufactured in the late 1970s. Thanks.

[@shilankalhor2072]

Thanks for the video, do you think that this machine can also be used to sew jeans with the right needle?

[@InStitches]

Thanks. Yes I think it will handle jeans.

[@pamelahardinger1293]

Hi, May I ask what class bobbin the air electronic takes? I have a Jubile type 45. Are they class 66 or class 15?

[@InStitches]

Hi, neither class 66 or 15 fit the air electronics. The Elna has a specific bobbin. Part number is 426000. You should be able to but them online or at your closest sewing machine supplier. Thanks.

[@pamelahardinger1293]

@@InStitches Thanks so much!

[@ellenmaries1]

This is super helpful! Thank you! A couple of questions (being a total noob in the sewing game): I have an Elna Jubilee and it is very similar to your machine in this video. So. How do I get a basic straight stitch, not an elastic straight stitch? I can't seem to figure it out.

[@InStitches]

Thanks for your kind comments. The right hand dial should not be set to - S +. Make sure it is on about 3 for normal sewing.

[@surajnarkar.7071]

Hi I have Elna 500 , superautomatic stich not work, only 1-6 stich works pls help me.

[@surajnarkar.7071]

Dear waiting for reply

[@pamelagahan5601]

I am buying the exact machine but they say the zigzag does not work. It only does straight stitch. It's only $25 so I am going to buy it. Can you tell me what to look for in the hope of fixing why it only does straight stitch I would very much appreciate it. Thank you. Pamela

[@InStitches]

Right here - kzbin.info/www/bejne/pai6iWOin7Sqg68

[@pamelagahan5601]

@@InStitches thank you so much. I bought the machine last night. It is one that takes cams but did not come with any of tools or feet. I've taken the top off and liked as you show in your video. I will continue to move it until it loosens for me. Fingers crossed it will zigzag after

[@dennisstyles9710]

I have the Elna Stella tsp air electronic but it is different to the one in the video in respect of threading the needle, does anybody have any clues to how to thread this machine

[@InStitches]

Maybe this video will help - kzbin.info/www/bejne/qZq6dZ5rf7l7pKM

[@ladinanya]

Thank you!!

[@InStitches]

You're welcome!

[@bibikhan909]

Can you show how to fix the bobbin winder

[@InStitches]

What is the problem with your bobbin winder?

[@giovannideramo8296]

Please help my Lena su has stopped doing zigzag any suggestions how to rectify

[@InStitches]

Maybe this video will help - kzbin.info/www/bejne/pai6iWOin7Sqg68 Thanks.

[@dormeliacedieu2081]

Wowwww very nice thanks

[@patriziacasamento6667]

Scusi lei li vende queste macchine?

[@sherrycothron9061]

Help my wheel is stuck will not turn needle up or down ( machine Elna Jublir (red in color) i had ran a new bobbin thread. When this happen? I push thé button on thé inside of wheel. Still nothing please help? Sherry.

[@InStitches]

It's difficult to say exactly but maybe the machine is seized? Try oiling as per the manual (find a manual online if you don't have one) and warm the machine to room temperature if you live in a cold region.

[@sherrycothron9061]

I hope not my mother left it to me she passed away almost 2 years ago.it was sweing fine i needed more bobbin thread done that .i noticed some thread hung up in the bobbin case so i pulled out much as i could. I think some thread could still be down in there .i do not know how to get this bobbin case out of there ?😪thank you sherry.

[@AM_Mechanic]

Thank you sir, this is one of the best tutorials I have seen. Very well done! 🧵🪡👍👍

[@dakotaanderson-sharples4594]

Is there any reason my machine doesn’t grab the bobbin thread? It isn’t this exact machine it’s the Elba Jubile duplex.

[@InStitches]

Try changing the needle first. Use a brand new one out of the packet.

[@baqarawan6520]

I need tool for that machine

[@sherrycothron9061]

Great video but still has.not help me with a loked up wheel pleass help.

[@InStitches]

Thanks. There could be many reasons for this issue. It's likely there is thread jammed in the hook area so try there first.

[@sherrycothron9061]

Thank you i will try it to see ?

[@mimiamina2881]

Catalogue pless whithe machine elnee

[@mariarojasgranda3207]

Me gustaría la traducción sea en español

[@malcolmduncan3047]

Tricot stich is pronounced "tree-co"...we can blame the French for that...lol.

[@PetronellavuyoPhillips]

🙏🙏🙏

[@dianarutecki9810]

I have one

[@giovannideramo8296]

Should read elna su