All I can say is that the roof sheets were installed back to front. First sheet goes up, then you should be able to route cables in the cable void of that sheet, then add the next sheet. Trust me I went through this today. Also that screw that went through the sheet into the beam had to be pre drilled, I destroyed the tips of half my screws trying to set that screw. Other than that everything was perfect, looks great and a quite sturdy once complete. Tips I would add - , you need a laser level, you need an aluminium cutting circular saw blade, a step drill bit and definitely a two person job installing those roof sheets.
@RU55KI17 ай бұрын
That is a very neat job, well done boys!
@qldroofingwarehouseroofing58947 ай бұрын
Thanks
@moevaevaeaki11129 ай бұрын
Awesome video lads … thanks a lot … not many videos out there this is by far the best …👑👑
@qldroofingwarehouseroofing58947 ай бұрын
Thanks
@casaMariaPT9 ай бұрын
Hi guys, I have this job to do this week in Portugal and I have been dreading it. After watching this amazing video I am now looking forward to it! lots of very useful tips and I'm loving the humour, wondering how many times Pagey caught the projectile between his teeth instead of his hands. Great vid lads, keep it up! Feliz Natal from Portugal!
@qldroofingwarehouseroofing58947 ай бұрын
Thanks
@watsonian56699 ай бұрын
Nice job boys...
@RomesDogs3 ай бұрын
scally did my carport they are awesome
@paulsapper4 ай бұрын
Great video guy Where do you run the cables for the LED lights?
@mosheva8 ай бұрын
very nice work! I'm amazed that you don't need any center beams and that the entire roof is laying on the wall and posts.. can you share some additional information regarding lighting and maybe a fan installation?
@qldroofingwarehouseroofing58948 ай бұрын
We can do that in our next video.
@qldroofingwarehouseroofing58947 ай бұрын
Will do
@MrLegendarydude3 ай бұрын
How did the roof support your weight when you were applying the sealant and foam? There was no beam under it..
@catalinneculai45413 күн бұрын
not even screws in the posts :))
@ntheweldingprofessional23354 ай бұрын
Bro you missed the lights good install tho
@shanegent58049 ай бұрын
Good vid guys. Did you need to cut back each beam when you spliced them together or does the factory do this in advance? I really like that detail on splicing the beam as it give a much cleaner, stronger joint and other methods 👍
@qldroofingwarehouseroofing58948 ай бұрын
No need to cut it is done at the factory.
@qldroofingwarehouseroofing58947 ай бұрын
Done at the factory
@vaskodimoski5690Ай бұрын
Grinder on colorbond?
@IrieLC134 ай бұрын
Hey the bros. Is it normal for the whole structure to have some flex in it. When i grab one of my timber posts and shake it a little, the whole structure shakes/flexes. About 10-15mm of movement. Scared it might fall. Its about 10 months old.
@MrAwsomegАй бұрын
Think about bracing it.
@egidioborg34219 ай бұрын
Hi, what size is that receiver channel, and why do you have the wider part on top.
@qldroofingwarehouseroofing58948 ай бұрын
The wider part goes on top to stop water. The size depends on the thickness of the panel.