For anyone having difficulty with the lid part of the video and getting an error that reads "Flow Simulation Error - Face is not laying on the boundary between solid and fluid region.", put the model in cross section form and press the inner face of the lid. He mentions it in the video but when he presses the model it looks as if he pressed the outer face (he didnt) which is what actually renders the error.
@danbanowetz4 жыл бұрын
Thanks! Great Tutorial! I believe the reason the nozzle helped mix your fluids was because when it accelerated the flow, it increased the Reynolds number and brought the flow from laminar into the turbulent flow regime. Turbulent flow will offer much more mixing than laminar flow. Does Solid Works Flow calculate Reynolds numbers? Or is that more of a "bulk" fluid number that doesn't make sense to calculate for individual fluid elements.
@Nixon_30003 жыл бұрын
Question: What if the inlet flow relies on pressure? For example i have a model which has a compressor that will supply air into nozzles. What if the initial condition of the model requires pressure but not flow rate? What should i do?
@bdkttroy54 жыл бұрын
Great tutorial! Thanks for sharing! My only request is a few configuration iterations on mesh development.
@emilmanuilov68796 жыл бұрын
Please tell me, why after clicking run simulation, program reports that monitor cannot connect to solver. What can it be? Thanks in advance.
@عراقالعلمِوالثقافة6 жыл бұрын
This is because the your computer has low space RAM> This is problem also happened with me
@banduobeyesekera353 жыл бұрын
very good explanation and presentation. Can you explain about super sonic flows on boundary layers, and how to set up the mesh properly.
@Greco111411 жыл бұрын
I think is because your model is not enclosed properly. Not sure though. Are you running the Flow Simulation in an assembly part?
@SanthoshKumar-bm9kh9 жыл бұрын
i customized my menu and added flow simulation but i did something ( reset to factory defaults i guess) that i cannot find the flow simulation option the next time even in the customize option. where and how can i find flow simulation option. please help me
@عراقالعلمِوالثقافة6 жыл бұрын
this is because no install flow simulation option when installed the products of SolidWorks. Re install the solidworks agin and activate the flow simulation option through the install
@nickmeisner62475 жыл бұрын
Should do a study of an Innova disc golf disc. "Hello, Innova here doing a study on Innova."
@eh_mamas80383 жыл бұрын
I am interested in simulation, can you help me make a horizontal centrifugal casting simulation tutorial, using the SolidWorks application. thank you🙏
@dumstzzile8 жыл бұрын
thank you soo much, am new in solidworks and I am looking forward to learning more from your knowledge.
@timtruo12 жыл бұрын
Thank you Matthew for your time and expertise.
@assadsayed483410 жыл бұрын
Thank you for the great tutorial, Do you have any tutorial about heat transfer (radiation) through multi-layers wall
@Serhiy343 жыл бұрын
User level - God!
@jesusreignonhigh67327 жыл бұрын
is possible to use the simulation on an assembly?
@consumerelitist65084 жыл бұрын
For some reason I can't get the water to flow to all parts of my model. It only really flows in the main pipe but not the lateral pieces.
@bartleycai27594 жыл бұрын
Check your gap sizes in your mesh settings so that the solver recognizes that there is indeed a "hole" or branch. Or check your trajectory sizes.
@consumerelitist65084 жыл бұрын
@@bartleycai2759 Thanks soo much Bartley! I'll that is most likely an issue I need to pay more attention to. I'll continue to refine the design and test the results.
@himanjalsharma11 жыл бұрын
same problem no idea what to do did you figure it out yet?
@wkbassett8 жыл бұрын
Fantastic presentation. Well done!
@ilc1534110 жыл бұрын
Very nice! I hope to be able to analyze similar structure for combination of gas.
@Mikesplanes548 жыл бұрын
Hi Just wandered if you are still around and are you able to help?? Mike
@mawsome6 жыл бұрын
can you do a heat transfer tutorial on heatexchnger plz
@Small133711 жыл бұрын
Just a little comment. If you add 1 g/s of water and 0,1 g/s of etanol, the volume fraction you would try to achive is 0,1/1,1 = 0,091 and not 0,1.
@SohilShah_Melodyman5 жыл бұрын
very well explained! Thanks for sharing.
@anuraghari97386 жыл бұрын
This was brilliant. Thank you so much!
@renoona12 жыл бұрын
This is very useful...thank you very much!
@marzouguiomar18489 жыл бұрын
thank you very much, that's so helpful
@KhanhNguyen-rr5ek10 жыл бұрын
It's very helpful. Thanks yoiu so much!!!
@tebogotlou50566 жыл бұрын
Thank you this was very helpful
@erank2411 жыл бұрын
Great video, Thanks.
@BeAWC5 жыл бұрын
Its very helpfull thank you so much
@rasta5936 жыл бұрын
Awesome!!
@himanjalsharma11 жыл бұрын
Nope I am trying to run it on my sld part file
@liychao197311 жыл бұрын
很棒!!
@emonpaul477110 жыл бұрын
it's great
@Nitrogenes11 жыл бұрын
The best
@rodriguezarthurs10911 жыл бұрын
thnx
@amarrvirk488611 жыл бұрын
Great
@dumstzzile8 жыл бұрын
thank you soo much, am new in solidworks and I am looking forward to learning more from your knowledge.