DIY Tutorial Build Your Own LCR Meter from Scratch

[@will2rein]

I'm very impressed. I have some experience in electronics and Arduino programming and I can say that this project is a great success, worthy of being built, studied, and disseminated. My warmest congratulations.

[@abuhafss1]

@6:09 The resistor tested was 27k but result was 17.91M.

[@innoconnecttech]

17 KOhm

[@МаркДанилов-ч8ж]

7:21 electrolytic capacitor = 89pF? 7:22 С(1n4148) = 95nF?! Your tester is a big liar 😀

[@karelbenda5322]

Wiring diagram and PCB image are missing.

[@snooker216]

Why did the soldering change from 2:30 to 2:50 in the video? There are 3 additional wires soldered from Pins 4 to 6 on the IC socket.

[@SRelectric]

Wow cheap and useful👍

[@buddhimaamarasinghe9997]

Thank you very much for responding to the request.We expect such valuable videos from you. Thanks.

[@masoudmontazery907]

Good luck sir 🎉

[@AbhishekKumar-zc2by]

Great project boss but I'm tring to download the code but code are missing,why?

[@RixtronixLAB]

Nice video shot, thanks for sharing it, keep it up :)

[@magia-dalla-Sardegna]

Salve, peccato che sul blog non ho trovato il codice arduino da scaricare una foto del circuito stampato per inciderlo da me ? Grazie a tutti

[@newscientificdiscoveries6228]

The link doesn't work for circuit and code

[@chotuusian4127]

Good work

[@inventorkr1]

Thanks for your kind words! It means a lot to me.

[@ingwarrce9900]

Presnost? Na akej frekvencii meria indukčnosť a kondezatory? Indukčnosť viem zmerať v programe ARTA v PC.

[@airoflex]

I can't find the code to download it, for an arduino nano will do?

[@RN3RBZ]

Никто не может найти коды, потому что их нет!

[@airoflex]

@@RN3RBZ Найс 😅

[@sarathighosh8033]

Nice video

[@allpha3638]

I cant find real wiring diagram (with resistors, capacitors, and quartz crystal), and code. Any ideas, please? Thank You for help.

[@user-vita1977]

То чувство, когда только что купила тестер и начала смотреть видео.

[@vipulakularathne3664]

From where it possible to buy these components....? Pl. Advice me

[@ooooooooooooooooooooooooooooow]

Super cool bro 🗿🍷

[@muammerdamar]

Good 😉👍

[@bennysofficial_ghostsogon]

Perfect Boss👍🏻👍🏻👍🏻 Nice Boss ⭐⭐⭐⭐⭐

[@moobdi3]

Where i can download the arduino code thanks

[@inventorkr1]

It's in the Arduino codes upload box in the blog

[@moobdi3]

@@inventorkr1 I couldn't find it Give me the direct download here thanks

[@ZAFERYILDIZ52]

wow Super

[@hisar3428]

Selamlar :) videodaki dijital ekranda Türkçe yazıyor bu kanalı Türkler mi yönetiyor yoksa video konusunu Türk birinden mi aşırtmışlat

Sanırım ikinci ihtimal. 🙂

[@DesertVox]

You didn't include a BoM for this project.

[@kamalfarai15]

your DIY doesn't measure the capacitance of Cgs and for led and diode , that make them weak , sorry

[@kimiya40]

Accuracy: The measured resistance was 17k, but the device showed 17.91Mohm

[@haydebre]

Çok başarılı, tebrikler. Arduino ile Ubuntuda IR alıcı verici ile TV kumanda nasıl yapılır?

[@ANIL2777]

hii can u share circuit conection diagram

[@Automation28]

nice!

[@John.Doe.2025]

Where is LCR meter?

[@smptvictor]

электролит не правильно определил 7:22

[@guoguo101]

Nice video shot，but' LCR meter codi'I don't know the password yet, thanks

[@inventorkr1]

inventor KR

[@rakeshvv2465]

Where is the code

[@lovediy8784]

hello bro. can you know how to measure earth resistance with arduino?

[@zvotaisvfi8678]

two ground rods measure the distance between them and impedance. A single rod is probably about half that impedance. add your wire to the setup and subtract the first measurement. Probably nothing will show up on a resistance meter so you might need a 1.5V+ battery to set a bias. and then you measure the leakage current and v=ir

[@youtubetv7000]

SUPER

[@brianwood5220]

What about in doctors? You didn't test them.

[@rodolfo8761]

Arduino code?

[@elektronikdevretasarm]

330nf neden 400pf okudu

[@G-Code_official]

Why didn't you test any inductor?

[@will2rein]

Here is the specific project for inductance testing kzbin.info/www/bejne/a528c4eoqpKsr8U

[@jgm1390]

Hola. Me gustaría saber si alguien lo ha hecho ya que tengo algunos componentes para fabricarlo. De ante mano muchas gracias.

[@ekremkaya9527]

elektrolitik kondansatörü 93 pf olarak ölçtü!!!!🙂

[@sawungsariti6871]

jos

[@theGraphicAutist]

didnt see any inductors...

[@squarewaveelectronicsankan8338]

Code

[@petrumanole9684]

The capacitor 224J63 is a 220nF at 63V and the instrument shows 261pF...see at 7:11 minute...it's a crap rcl meter, it doesn't worth, it's a waste of time and money...

[@БарабашАлександр-э5л]

"Схемы и код можно найти в блоге..." а можно и не найти 😂 Тогда зачем все эти телодвижения в видео, если достаточно любой готовой платы Arduino, почти любого экрана, шести резисторов и кнопки?

[@dogabelgesellerikusagi3391]

Yakalandın 03:30 da Türkçe var 😂

[@xaiver3612]

malzeme bulunamadı...

[@manddrohid-nl3yn]

bel effort , mais ... putahclique ...

[@aliemlek]

👌👍

[@Yate669]

Abi sen Türk müsün

[@kasper3355]

прошивку нельзя скачать. а без нее это совершенно бесполезные мультики. схему подключения дисплея с нокии можно найти в даташите дисплея.

[@electroniquepassion]

👍👋👋😉

[@s12-hh8rk]

Извините есть идея.Можно теоретически проверять и оптотроны🤐

[@youtubeviewer7077]

Music sucks and is loud. Better to describe what you're doing, even robo voice is better than terrible loud music only. Cool project though.

[@sherzodkuchkarov1885]

😳😲👍👍👍

[@robscat1979]

нет защиты от статики!!!

[@sammin5764]

🌟🌟🌟🌟🌟