inverter welding machine amp display blinking problem and turn on and auto off after few minutes.

[@euloomulquran4585]

Thanks bro after long time I fix today , because of you , thanks 🙏

[@kalacsaron1207]

TNX po.. more power 🎉

[@rahulpatelgujratahmedabad3497]

Good tiching karte hai 👍👌👍👍👌👌👍

[@dgayansampath]

Hi, when you upload videos next time pls add sinhala language for subtitles. I'm from srilanka. Thanks.

[@pawanverma3564]

Good job sir ji

[@ranjeetk333]

Thanks for the video. Sir ntc heat ho ke machine off ho jati hai kya fault hota please tell sone solution .single card igbt machine hai.please

[@ranaelectronicelectric]

Please change relay

[@kalacsaron1207]

luv u po

[@AhangarRashid]

Where you purchased this vacuum pump , share the address.

[@jaybeebowy]

What liquid did you used to clean the board?

[@donzonzon2499]

I have kzubr 400mma welding machine its works fine when i shut off display is blinking and fan trying to work in intervals on and off when i cut a power, reley click one more time sometimes two and green ligh blink with display aprox 3 4 times what is the problem, in work is very good but this is anoying

[@vishwakarmaacfrigerepering7803]

Sir welding mashin he usme dispaly on v nhi ho raha.he kam nhi kar raha.he on nhi ho raha he kya chek kre usme sir

[@leonarddranoel2511]

Am working on welding machine with this same fault and it have no relay , I have tried fixing it but I have gotten it right but I knew voltage is missing some where around the small panel, please I need assistance

[@omprakashsingh5508]

Nice

[@ranaelectronicelectric]

Thanks

[@omprakashsingh5508]

Thanks for reply

[@omprakashsingh5508]

Thanks for reply

[@TekkHakk]

i have a mig 125 power light flickers fan spins slow , could it be the relay? why is there 300+v dc ? can you can explain or have a schematic ?

[@sagittariussurge5565]

Mine too but I don't get help ...I ask around but never received any help

[@jhunsorreda-gt2yg]

San po location nu? Pa repair po Ako ng welding,tnx po!

[@anandrana6389]

Nepal

[@preindstv2079]

boss saan ba nakakabili nyang relay meron b sa lazada?

[@balberojoelchannel1054]

Pareho Tayo ng sera sa portable ko blinker din Ang display.

[@kevin28835]

Cambie el rele y sigue haciendo lo mismo, qué mas podria estar fallando

[@aabidelectrical5599]

Sir meri welding machine output voltage nhi aa rha h। Display error dikha ta h । Please your connect number ।

[@harishsinghnegi9768]

सर मेरे पास एक वेल्डिंग मशीन एलिफेंट प्रो की मिनी मशीन है सर इसके आईजीबीटी फट गए थे तो मैंने रिपेयर किया इज 60N60 के लगे हुए है मैने चारो आईजीबीटी लगा दिया पर ड्राइव वोल्ट 6 वोल्ट के आसपास आ रहे है सारे रेजिस्टेंस भी चेंज कर दिए फिर भी आईजीबीटी लैग्स पर 6 वोल्ट आ रहे है प्रॉपर 12 वोल्ट नहीं मिल रहे जिसकी वजह से आईजीबीटी बार बार उड़ रहे है सर बताए कया करे बहुत नुकसान हो रहा है

[@suvasgaming556]

Hello sir all ok desplay but not output

[@yaps1601]

ខ្ញុំបាទ

[@yaps1601]

ខ្ញុំបាទអរគុណអ្នកដាំដើមវីដេអូបងដាច់ជួស

[@cereloruwelmanuba2760]

Location sir papagawa ako!

[@bernardcuinto5463]

Bat good naman yong relay sakin ehh nag bliblink parin

[@kutondiy1049]

nagpalit narin kau ng relay sir

[@srinivasuluvasu1603]

Thanks for your help

[@samshertoor.7toor400]

Good work 👍