iPad Mini Glass & Screen Replacement (digitizer and LCD removal and installation)

[@gridarmorfix]

Use dental floss under the screen to get through the glue so you are not prying up on the LCD to limit the risk of damaging your lcd.

[@alexmobley4017]

Excellent tip helped me a lot

[@EdvinKosenkov]

Good tip, will try on next device

[@JonnyRash]

Thanks for your great video. With your help I successfully replaced the flickering LCD on my daughter's Ipad mini. I replaced the screen at the same time because I was expecting to break it when removing it. Very pleased that I managed to remove without damaging the screen so I now have a spare one. By the way I used the suction pad from my Go pro suction cup mount. It is so powerful I could have pulled the screen off without the use of a blade. For those of you who are asking about how much heat to use, the glue becomes soft when it is a bit higher than body temperature. Keep that heat gun on there for too long and you may well destroy the other components inside, particularly the lithium battery!

[@kei51movie]

If you have cracks on the screen, it is better to apply the duct tape on the screen before taking it off, then you don't need to worry about scattering the glass around. Thanks for posting this video!

[@Laptopscreen]

Suction cup can be found on the soap holder in the bathroom, alternatively there is one shipped with the iPad Mini digitizer sold by LaptopScreen

[@jmellis41]

Thanks for the video. Most informative I found and the suction cup method is, without a doubt, the best way to get the removal started. Everyone else recommended a razor blade which will scratch the finish if you're not EXTREMELY careful. Appreciate all the time you put into this.

[@peterislazy]

Hey just a quick tip, when you have both the lcd and glass tilted over, instead of holding it the whole time you can place a suction cup behind the glass and have it rest on it.

[@FreedomForce100]

Removing 3 layers to repair the top layer... what a terrible design! Great video. Thank you!

[@Baghuul]

Its made like this on purpose to deter you from repairing it yourself.

[@fakefamehunter4590]

It's much better than the designs as it cheaper to repair if only the front glass needs replacing

[@rezstitution]

good idea to TEST digitzer and LCD before you close it. or else you'll have to put new adhesive.

[@pjb7033]

I found that before disconnecting the LCD connector the battery connector should be removed. Otherwise you run the risk of damaging the backlight fuse. Wish he would have mentioned that.

[@kevinfinucane2409]

Yes now I think my backlight fuse is blown because he didn’t say anything about it

[@overknight5278]

Kevin Finucane your supposed to turn off the device, and disconnect the battery first. But ive never had an issue with any iphone or ipad ive fixed where disconnecting the battery last (on accident) . The thing is if there is dust in those connectors, or anything, it can make a connection fail (which has happened for me on my 5s, the screen would turn in but the digitizer cable although in wouldnt work b/c of dust Just check and make sure.

[@preshitamalhotra1267]

Received in perfect condition, the item said it needed to be signed for but I didn't. I love it. Bought my mom one for her birthday on Amazon prime day

[@hycocam]

Thanks for the video. Wish I had seen this one before fixing my 1st mini--really easy to crack and/or overeat/discolor the LCD screen if you are not careful loosening the glue. This method is one of the better for getting digitizer safely separated.

[@AlleyKatzTV]

Can vouch for LaptopScreen, these guys sell these screens almost at cost and they are so easy to install its insane that electronic stores can charge so much to repair screens.

[@donaldds9528]

I want to compliment you on a first-class tutorial, because you know how to instruct your viewers clearly, unlike many others. I have come here as I need to fit a replacement screen on a Mini 5. I have one question: is the Mini 5 same as the other Mini versions, please?

[@Laptopscreen]

Thank you! Yeah they are all going to be about the same. Just look at your replacement part - where ever the cables are - be careful in that area when removing old screen.

[@donaldds9528]

@@Laptopscreen The model I have has no screen!

[@nueasia]

just ordered a kit for my ipad mini 1st gen that i haven’t used in years because of the broken screen, hoping ill be able to access old photos

[@spooksvstheworld6731]

The best vid on screen replacement I've seen well done and thanks. 👏🏼

[@nawaz4it]

on 2:18 SECOND of the video, how were you able to band/fold the LCD completely on top of screen, ??? And i broke my black color of screen on top of lcd while trying to take out LCD,

[@joesalamone3882]

Can i use the old lcd if i just need to replace the digitizer

[@mattmoyer1912]

+Joe Salamone Yes, provided it doesn't crack during removal.

[@amaized1]

Thanks so much! My process didn't go without some issues but I couldn't have pulled through it without your awesome instruction. Most importantly, my iPad works!

[@scottabdo3637]

the video was spot on, took me about 45mins and works as good as new that you for posting this, hint the glass is a little tough ti get off

[@nightmareinaction629]

Scott Abdo took me less than 10 minutes but probably because I have so me this with ipad air and a couple iPhones makes good money trust. Me about 90 dollars profit all the time

[@princessandcocosisters3078]

Most screen digitizer being replaced has a black plastic tape covering the home button up to the flex cable being connected. Meaning the back of the home button shouldnt be exposed. Why is this diferent will it still function?

[@zhengtli]

One important part that's missing is the magnets. There are two magnets on the digitizer. The new one from ebay usually does not come with them. If you don't notice, you will not be able to use the smartcover. I missed and threw them away with the broken digitizer. Only after I put on the smartcover, I realized.

[@HOTRhuntinontherock]

Hi I can you tell me what part of an i pad is the actual storage compartment? I think my iPad has a deeper issue. So I was wondering if i can remove the storage compartment and replace it into a second ipad.

[@Laptopscreen]

Ugh, it's a chip on the logic board. If you want to know more look up Jessa Jones from iPad Rehab on KZbin. You'd probably be better off sending the two iPads to her to do the work and pay for her time, its worth it if you really need to get your data. But at-least its doable.

[@Laptopscreen]

You are referring to the digitizer IC piece. We now sell no-solder-required kits for iPad Mini.

[@roncrandall4174]

Liked your video.I have a blank screen created by moisture, not directly dropped in water. It gradually spread and finally went dark. I can hear a beep when connecting the power cable, but no other sights or sounds. Screen looks good. I slightly opened and tried to dry it out with some hair blower heat. I have new screen and digitizer but am beginning to feel the problem is probably the lcd. I can and have backed it up on my mac. Questions: 1. does it sound like the lcd? 2. Will I also need to replace the screen? 3. How can I tell if it is powered on or off before I start?

[@j.lietka9406]

Did the new digitizer come with a home button? Thanks

[@carinthian]

I replaced only my digitizer with IC already attached. The ditigizer works fine when not glued down. As soon as I glue it down the lower left hand corner off the screen starts activating randomly, and idea?

[@Laptopscreen]

Best guess: reconnect the digitizer. If that doesn't work a new digitizer may be needed to restore functionality.

[@adrianformaran4361]

please show the details on how to re-attache the connection of the digitizer to its connector?. thanks

[@Marko-xc4vn]

When I reinstalled the digitizer and LCD, I tested the screen and it was very dim. I checked the LCD connection and it was aligned properly. Any advise on how to fix this issue?

[@Mokosobipolar]

My ipad mini felt and now i can barely see whats on the screen like if the resulution would be really really low what can i do? thank you so much

[@jvpot3693]

Can i use hair dryer for heating the sides ?

[@nightmareinaction629]

I find those screws right next to the magnet stupidly hard to put back in if you have an ifixit like I do use the twicers the look like needles at the end to hold them I'll make it easyer

[@JaimeMendozaZambrano]

how difficult is to repair the ipad mini screen for some one with no experience or rapairing skills? could you give some advices and warnings to avoid making big mistakes?

[@charlesmckenney3391]

very informative and right to the point, Not like some videos where the speaker drags it out talking about who knows what.THANK YOU

[@Laptopscreen]

Thank you Charles! Completely agree, will keep on getting right to the point :)

[@MultiWilliam121]

As i watch this i drop my ipad face down and its now cracked... Fml

[@Laptopscreen]

+mine william Sorry to hear about that. But look on the bright-side - you now get to take it apart!

[@MultiWilliam121]

Ya hehe

[@Redrot13]

mine williamp x

[@dEezNutZDoOLiST]

It took me a second to realize he meant his iPad cracked not his face hahaha

[@Laptopscreen]

Oh lol... wait whaaaat?!!! So it wasn't the face?

[@jaatrathi7858]

What is the price of screen and folder

[@fallendawn8552]

Thank you. I broke my lcd trying to fix my screen last Christmas trying to get a new screen on

[@randomlonglegcat7973]

Same here buddy

[@MagicalBacon]

Can you use a hairdryer to make it warm?

[@evanbeebe4171]

Lettuce yea

[@5444067]

Yes

[@heatherklein9139]

smashed screen and part of the corner of led screen help

[@Laptopscreen]

Hi there, it should be fairly obvious if the LCD is damaged - black "ink" stains, straight vertical lines, etc. If only the glass is broken the picture should be fine, except for the cracks overlaid from the glass. The $46.99 is the actual LCD (not a touchscreen), glass IS the touchscreen (digitizer), so if the picture doesn't show black "ink" then only glass needs to be replaced.

[@ultimatetechsite]

_great_ video. Learning ipad repairs, I have watched quite a few of these. This one is one of the most thorough and best produced. Thankyou. I have one question - where can I obtain the suction cup from?

[@jaycee7440]

I replaced my screen digitizer. I must have done something to the charging port motherboard.. everything works except it won’t take a charge or show up on my computer ITunes.. once the new battery dies..I can’t recharge.. any tips? I did about 10 different cleaning procedures to port.. I see I scratched one of the 2 long thin bronze colored Metal parts coming from the charging port, with a screw driver taking off the protective tape..

[@TheKnowledge212]

Ok so it looks like I only need the screen then. Do you sell the screen? How much? I only see the LCD available.

[@Laptopscreen]

We do have both for sale, although the stock varies. Please see the iPad Mini listing on our site.

[@kennethfactor7763]

LaptopScreen.com do you repair ipad mini 2 sir?

[@Mauvelich]

I accidentally rip one of the mount tapes from the LCD does that affect the LCD!? Because now i see the screen really low Bright

[@Californiamartinez]

Does the iPad mini replacement screen available on your website come with the home button and replacement cables already soldered as you show in your video? The picture on your website does not show the home button in place.

[@kelvinjones2414]

At 2:20 in the video, this guy has the LCD flipped up...... this can only be done if you untape the LCD along the connected edge.... otherwise you'll crack the LCD. If your LCD is already broken then don't worry. Remove the tape to save the LCD

[@shapiroezra]

Thanks! This is a great video. It's hard to screw up with these instructions.

[@JobSaunders]

Hi, before ios 7 comes out, I want to be replace my ipad mini. Replacing an entirely new ipad sounds great, but its also really expensive. Then I found this video, and realized it is a lot cheaper, but it definitely looks risky. Incase i ever do think about doing this, can you give me any advice of doing this right so I won't risk breaking my ipad. How often do you think people watch this and get it right without breaking their devices without experience of practicing these steps?

[@Laptopscreen]

LaptopScreen doesn't provide mail-in repairs yet. However iPad Mini, as seen above, is not the most difficult repair imaginable, we'd rate the difficulty (on a professional scale) as 5/10: using appropriate tools and plenty of patience, a first time repairer should complete the job in under an hour. As well we now sell direct-drop-in iPad Mini parts (no soldering required)

[@ModernGamify]

I cannot get the screen off. I have heated all around the iPad for over 1 minute. it's hot on every corner but will still not come up with suction cup. I try to slide putty knife in but will not go in. help me please!!

[@Laptopscreen]

True the mid-shield with all these screws is a little inconvenient, however we have to point out, that with such shielding iPad mini could potentially survive EMP or solar flares in a cataclysmic event ;)

[@deandrewaites3530]

I have 2 of the same iPads one of the screens is totally smashed all the way to the lcd the other is locked can I switch the lcds ?????

[@Laptopscreen]

Yes, you can!

[@smokegamingchannel5370]

how did u smash the lcd lol i fixed my ipad 3 screen for $20 lol technician here in the philippines are awesome

[@blueeyesliz1]

should only glue down after a small test to see if all is functioning then glue or you may run into the whole process again

[@floridajames04]

is this the way to do the screen replacement without soldering??? i need a quick answer... thanks

[@ItsSupposedtobeloud]

Hey friend I went through all your steps and for some reason the iPad mini won't turn on now (it turned on just fine prior to the installation). I used a new digitizer screen and the old LCD (the lcd was not broken). Any suggestions??

[@Laptopscreen]

Try reconnecting both the digitizer and the LCD's connector with the battery turned off, and make sure all the insulator tape (especially on the LCD screws) is replaced properly.

[@blingcl]

same thing here

[@AutisticBeauty]

how do I turn the battery off? what exactly do you mean by that?

[@steveofsd]

I tried using hair dryer on High for 3 min. and is hot to touch, I use suction cup like you but fail to separate the upper left corner. So how hot is hot? do I need to use a shrink wrap heat gun? I even tried using two suction cups to pull on both sides of the corner and still fail. BTW I don't have a shatter glass, I just need to open the glass part to fix a ghost touching problem I'm having with my ipad.

[@Laptopscreen]

***** You could try pulling from the middle close to either left or right edge - where the bezel is the thinnest - and continue separation from there. The glue will be very tacky even when sufficiently hot - some effort is required.

[@mathewhuffman7056]

Does replacing the screen require soldering at all? Thanks!

[@Smallfred1]

((whilst I was replacing the shattered glass screen (digitiser?), I cracked the LCD also. Do I now have to replace this as well?

[@TheAPGamingGlitcher]

Yeah

[@TheKnowledge212]

Hi. I know that the glass is broken but how do I know if the LCD underneath is damaged? I see the price on your website is $46.99. Is that just for the touch screen? Does the screen come with the flex connector? Looks like it from the picture but I am not certain. The person that will be replacing it for me told me to double check. Thanks

[@juanrosales4680]

actually the ipad mini has magnet on both sides. but this small magnets on the corners. what is that for?

[@iggy_tea]

Juan Rosales the iPad smart cover

[@tennis5126]

The Ipad in the tutorial. Is it the 1st gen Ipad or 2nd gen? Thanks.

[@nicklaptopscreen9600]

+Jack Jones this is the earliest iPad Mini

[@auraelucidator715]

Anyone know if a glasses kit would be a good idea to use for the screw driver size?

[@Akye20xx]

hi, ipad mini 1st and 2nd gen uses same digitizer?

[@Aggression-hc3yp]

Each time I try to affix the new screen to the tablet, its upper right and lower left sides pop up after a few hours, despite having more adhesive strips to keep them down, and I keep heating them and putting them weight to apply pressure and allow the adhesive to set in place. What am I doing wrong?

[@Laptopscreen]

You could try to clean the adhering edges with alcohol. Clean both the inside of the iPad and the back of the digitizer. Clean it very thoroughly. Make sure all previous adhesive residue is removed and that the edges are dry and oil-free.

[@dantekilla9453]

It its pretty simple..The only problem I had was with the touch screen part.. My screen was completely shattered and I need a new one. Thats the hardest part you will come across..Also before you do this.. LOOK UP IPAD MINI SCREW CHART..Its a magnetic chart bigger than the ipad so you can place the screws on the chart that have the exact screw placements labeled.

[@MrMoffatt]

and if your blacklight fuse is broken, ipad will not turn on, since the connecters will be close to the fuse and the connecters will have the ability to short circuit the fuse or even damage and might injure yourself

[@jackofalltrades6717]

Great video, thank you!!! Very clear instructions. I replaced the glass of my mini Ipad and works like new.

[@ybnprince3344]

How much would u charge me to fix my iPad mini??

[@juanrosales4680]

I replace one mini ipad screen but I saw one of those magnets on the corners, what is that?

[@Proziee]

How long does the adhesive take to set up on the screen after applying heat?

[@StarboyBoss]

Proziee I have the same question, how did you get it to stay in place and come off? I used a heat gun and that digitizer never stayed in place.

[@Laptopscreen]

Jose Manuel Toledano The new digitizer should have new adhesive on it. You should clean out the old adhesive before applying the new digitizer. If no new adhesive is used you have to ensure that the old adhesive is not contaminated with finger oil, lint, dust or hair/fibers. Old adhesive may never work again is you have touched it with bare hands or let your shirt/sweater on it. Use alcohol and lots of patience/elbow grease if your old adhesive is contaminated to remove it all fully.

[@keenacummings3789]

My granddaughter dropped the mini iPad on the floor yesterday cracked the whole screen .. Does anyone know how much it is to replace the screen and where to buy to replace will someone PLEASE help me 4.25.18 TY

[@isaacclark284]

Do you have to go through this whole thing just to replace cracked glass? I looked at my iPad and it's only broken glass. Everything is responsive so am I able to just heat up the iPad then take it out and place the new one or do I just have to go through the whole process?

[@Laptopscreen]

Yes, you would have to perform all the steps shown in the video. You would need to disconnect the digitizer in order to remove it and reconnect the new digitizer to make it work. The digitizer's connector is on the logic board, under the LCD and the EM shield, that is why you would need to remove the LCD and the EM shield to gain access to the digitizer's connector. Watch the video carefully to understand the answer to your question.

[@brandonphillips3639]

How do you know that both the LCD and Digitizer needs to be replaced??? I have an ipad mini that is cracked, but the LCD underneath still works.

[@yusuffurkan419]

could i use a pencil instead of the metal pick, and how much harder would it be if i didnt use a suction cap

[@romefox]

Its reallllly tough getting the screen off without cracking it, requires lots of heat gunning and patience, doesn't matter what you use to keep the screen from re attaching, what you use to life the screen is what matters, I have not yet removed a screen without cracking it after many repairs, goosed thing is it was cracked to begin with hence the need for the repair lol.

[@Laptopscreen]

Yes, we do sell iPad Mini digitizers! (Also no-solder-required ones)

[@mattstevens1543]

Was I supposed to disconnect the battery before the lcd and the digitizer. I carefully did this just as you did and now the iPad mini display shows nothing. I plugged it into the charger and it has a chime every few seconds no display. Some threads say because I didn't disconnect the battery, I blew a fuse. Is this what has happened and how do I fix that now?

[@waynealty4287]

Holding down the power button and the home button at the same time often fixes this on ipads and ipods after screen replacement.

[@scratch6402]

So if my lcd display is fully functional I dont need to take it out?

[@-infinity-6705]

What type of glue should I use to stick the original control circit onto the replacement part

[@Laptopscreen]

Tin glue (solder) with a special glue wand (soldering iron). Its best to order parts with the digitizer control circuit already attached: www.laptopscreen.com/English/model/Apple/iPad~Mini~Wi-Fi/

[@AutisticBeauty]

how do I turn battery off? what does that mean? do I just shut the iPad off or is there a special way to turn the battery off? please explain in details

[@yashovaatskarnani9170]

Jessica Simmons just shut the ipad off

[@AutisticBeauty]

I did and the laptop still won't turn on at all.

[@nuveh.b.938]

So I’m trying to fix the iPad mini. I put finger prints on the LCD is there a way to remove this?

[@Laptopscreen]

The best way to remove the fingerprints is by using a microfiber lens cleaning cloth (glasses wipes) and breathing on the affected spot then wiping.

[@hlgb2012]

Do I have to backup all data before doing this?

[@Laptopscreen]

It is a good thing to have a back up regardless of circumstances. This procedure is not supposed to affect data - everything will come back just the way it was if only the LCD/Glass is replaced. But if something goes wrong during the repair - having a recent back-up will be great.

[@hlgb2012]

Thanks :-)

[@khalidmuhammad2098]

The very important step is after connecting the new digitizer and LCD , it is required to check if both are working good and then you can go ahead to close it completely otherwise if the digitizer is faulty or LCD is not good, the iPad is still open to replace them without re-open again and you still have chance to return the faulty digitizer or LCD to your vendor!

[@Everyonelove_Games]

You make removing the LCD look easy

[@Laptopscreen]

Thank you! The secret is to fiddle off-camera. There are plenty of videos of fiddling on YT, but its better to fiddle on your own.

[@MrPaulie1340]

So I went through this and a few other videos, made the digitizer replacement repair and holy crap! everything still works perfectly! Except for my official Apple Smart Cover doesn't put the iPad Mini to sleep anymore. Can anyone tell me where I might have gone wrong?

[@iBRCKsHD]

Do you have to disconnect the battery before the new LCD/digitiser goes on? I know in some iPads it blows the backlight

[@Laptopscreen]

Only if you are planning on shorting out the connector by trying to plug it in while its misaligned... Yes, disconnecting the battery would help to prevent damage that could occur from shorting the connector.

[@abnx9670]

Where do you recommend ordering the actual glass screen from? What is the estimated cost of the screen?

[@dynocompe]

+P Banks i would assume they reccomend their store at laptopscreen.com. Honestly I have bought dozen of computer screens from these guys, and they are a superior company to deal with, here in Canada anyways. Love them. Also I buy from their ebay store as well for brand new screens that are not grade A, ex. has a small scratch in new screen, missing a mounting tab, a few bad pixels(i never buy those ones) can get some killer deals though!

[@Laptopscreen]

+dynocompe Thank you for your endorsement!

[@rsmit11]

Fuck, my friend hit my iPad mini out of my hand by accident and the whole screen smashed badly. Then my parents repaired it for Christmas. Now my dog was eating a Kleenex and I put my iPad on a counter and ran over to get it out of his mouth. It fell down and smashed again. My parents aren't home from work yet. Omfg I'm so nervous.

[@Laptopscreen]

+TheFlamingArrow You could tell them that the dog was casually eating its daily fill of Kleenex when you sneezed and got into a little scuffle over the last of the Kleenex. You won the scuffle, but the vindictive canine, unsatisfied with its forcefully diminished portion of daily fiber, proceeded to take out its revenge on the unsuspecting iPad. It knew full well that doing so would put you in a precarious position, since the iPad was previously repaired at great cost; but choose to execute its revenge with cold-calculation and malicious intent to cause you the most grief. Or you can tell them the truth and that you can now repair the iPad on your own, and that the parts cost less than $30, but the experience and the satisfaction of fixing the device you own by yourself - is priceless!

[@haydenmarschall3233]

Uh oh

[@elibarikimishetto3338]

best shit ever

[@nipengrg4109]

Help🙏🙏 My iPad mini2 is broken glass I can see some black glass panel from the broken screen It is inside the broken screen Is it lcd? Do I have to replace the led too Or only the glass I know glass is broken but hope the lcd a not broken because glass protects it

[@Laptopscreen]

+Nipen Grg A broken LCD cannot be mistaken for glass damage - when the LCD breaks - its clearly broken with splotches of black, cracks and lines. You can Google "broken LCD" to see examples. Read more about digitizes and LCDs here: www.laptopscreen.com/English/section/Articles/1245191276/About%20touchscreens/

[@onee-chan7688]

How much is the lcd repair???

[@Christian-mh9sh]

King Hearts Somewhere between $120-$150 and thats only the lcd

[@emmettturner9452]

This screen feels like it will crack if I lift it far enough to access all 16 screws underneath. What gives? It isn't stuck to the back plate.

[@jaimeguerrero8588]

yes behind the lcd screen there is adhesive you can use dental floss to remove the adhesive slowly till the part where the connectors are placed

[@jeena256]

Hello, i changed digitizer on my iPad mini, it works fine, but only for a week. Now the digitizer stops reacting, home button works. Can you help me?

[@adam_barnes]

What if I don’t have a suction cup though??

[@LeftyyyTV]

Do you need to replace the LCD if you replace the digitizer?

[@Laptopscreen]

***** darktroop6 Not if it's not broken. There are no direct relations between LCD and Digitizer in the iPad. Just like on a desktop: you wouldn't replace your monitor if the keyboard was cracked.

[@Laptopscreen]

***** The LCD is removed to get access to the digitizer connector. Once you unplug the old digitizer, plug in the new digitizer, the LCD can go back in (original or otherwise).

[@FakeExotic]

Yo my screen won't stick to the base properly, now dusts are coming inside my iPad. What should I do

[@Laptopscreen]

Purchase new adhesive (specific to your model), clean off the old adhesive well, wipe the edges with alcohol, straighten out the corners, slap on the new adhesive.

[@Laptopscreen]

We do have no-solder-required parts now, but they sell out fast.

[@9olevels]

Well made 'how to' video with excellent instructions! Thanks :-)

[@Laptopscreen]

At the time of making of this tutorial, no replacement parts were available at all. A month later, and for duration of several month, only "non ic" parts were available. Now, we sell "no solder required" parts. But you are most welcome to make a tutorial on your own that will show the soldering procedure - it will surely be greatly appreciated by everyone :) If you make it as a video reply - we'll make sure to post it!

[@kntwing23]

hey someone gave me a broken i pad mini..the front screen was crack broken but still can use? if i want to change the whole i pad front & back cover? can u change the back cover my color is gray?i want a new back cover also? u sound like you're chinese person? where u located at?

[@Laptopscreen]

Yes, yes, a Chinese person, naturally, from your local Chinatown no-less. Come see me between the fish stand and the ginger root hut. I give you good price, cause I love you long time.

[@DreamCatcher201]

The LCD broke while following this video. Remove all glue “tape” before pulling the LCD. Lifting the LCD is harder than it is portrayed here. I’m really sad it broke 😔😔