ISUZU AUTOMOTIVE ENGINE CONVERTED TO MARINE TYPE

automotive Engine to Marine Engine conversion

[@mbkomfort]

A couple of advice: you should not need automotive u-joints on the propeller shafts if you align and straighten up the driveline properly. The cooling water line/pipe going over the header tank /heat exchanger will trap air. (Run small pipes from air traps to a common higher mounted expansion tank to avoid ) Good luck with economy build :-)

[@rouqeann]

Good idea. Nice advice

[@mbkomfort]

@@rouqeann those u-joints are made to take torque, not thrust, and the propeller shaft transfers thrust from the propeller to the transmission, and torque from transmission/engine to the propeller.

[@edgardomingo4846]

Modification of this engine is possible but need to study the consecquences and effect to avoid accident specially this is passenger vessel and i think maritime authority has a regulation and class survey of the seaworthy of the vessel before they approve for sailing,

[@rouqeann]

yes class societies and authorities will check the vessel before approval

[@MultiMeadows1]

Ang isuzu may mga marine engine na pwede mabili surplus or brand new. Ang mga isuzu diesel engines may mga marine version yan

[@rouqeann]

Ok po

[@KhemCabebe]

Pwede ba sa heat exchanger yong hindi sea water ang gamit?

[@rouqeann]

mas maganda po pag sea water heat excahanger dahil marine type po ang sea water heat exchanger,

[@xxxxxxxxxx1600]

Sa tingin nyo po ba possible ang fiberglass yacht yung mire than 90ft ang length? Yung standard multi-million yacht tulad nung kay willie revillame? Kasi dito samin yung nga fastcraft, single hull po hindi catamaran, 90-95ft ang length, tapos 18-20ft ang lapad tas 2-storey. May nabasa kasi ako na foreign national na hindi daw structurally ideal yung fiberglass sa malalaking vessel? Kung napanood mo na po yung abandoned unfinished fiberglass/wood yacht sa Cebu ata yon.

[@rouqeann]

Tama po lods, d po ideal fibreglass sa malalaki. Kailangan na po yon ng mas malalim na design structure. Pwd po yon pero designer company na talaga gagawa

[@butchcantara1497]

Sa probinsya poh namin 130ft twin engines C32B 18 to 20ft ang lapad, pero makapal poh ang dingding o intable 2inch ang kapal almost 10M fiber boat palang.

[@renejosezacarias8376]

Mga magkano kaya gearbox sir

[@rouqeann]

marine transmision medyo mahal din po sir, nasa 100k above,

[@parengjhunxkie8970]

Nasa magkano na yung marine gearbox ngayon?

[@rouqeann]

depende po lods

[@sambh3632]

0:11

[@rouqeann]

.11

[@kdgarcia-gv7qu]

magkano ang gastos sa gearbox

[@rouqeann]

transmission d po ako sure, medyo mahal din

[@anthonygasid2765]

magkano ung kabuu ang gastos sa ganan boss?

[@rouqeann]

8 to 12 million po

[@juriemorata]

Anong engine model yan idol rolls, ilang horse power yan.

[@rouqeann]

Nasa 300 po lods.

[@reybigot3800]

Ilang nots takbo nya lods

[@rouqeann]

nasa 16 knots lods

[@reybigot3800]

@@rouqeann ok matulin Yan ok see you next vlog

[@LeynesBrother]

Loc sir po ng shipyard?.

[@rouqeann]

Tacloban area sir

[@sambh3632]

Need engineer for customize truck engine to marine engine

[@rouqeann]

Location sir

[@joylique8544]

Sir saan Po Ang builder nito?

[@rouqeann]

Tacloban din po lods

[@jasonfrancisco4255]

Sir mag Tanong Po ako pwd ba mag exam nang mem 3 na Hindi na mag exam nang MDM 1 atsaka MDM 2 or Hindi pwd dumiritso sa mem 3 or kailangan mag step by step muna?

[@rouqeann]

Kailangan po mem 1 muna bago mem 3

[@sambh3632]

Hi

[@rouqeann]

Hello

[@adeloignacio1644]

Following d comments still lacks actual experience.re cooling sydtem of automotive diesel engine

[@rouqeann]

Your right lods. Still need improvements for equipment and machineries installation

[@jceautodetailing6130]

Lods naa kay contact # number sa nag convert sa engine idol?pwd e msg sa fb nako idol c Johnghia ni idol.

[@rouqeann]

Pm ka po lods. Meesenger ko Ellon thomas

[@tanerko8582]

Puro ka tawa bakit?

[@rouqeann]

Dahil bakit