Hayward Power-Flo Matrix Sp1592. VIDEO ANSWERS THE FOLLOWING QUESTIONS: 1) How do I rotate the pump? 2) How do I install the pump using a union connection to the filter?
Пікірлер: 79
@albingatdula81634 жыл бұрын
Thanks a lot !! Push and rotate!! Easy right? Can’t find where that button is😂 good thing you’re here👍 the beauty of KZbinr 👍👍
@itribute18964 жыл бұрын
Glad it was of help to you. :)
@jerryra5 жыл бұрын
Thanks, That help a lot. I couldn't figure out how to rotate. You show it so I had no trouble.
@MikeFeuer5 жыл бұрын
Great to hear - glad it helped :)
@pinkbarbie__3 ай бұрын
I really appreciate you sharing this ✨🙌🏽✨
@6977warrior15 жыл бұрын
You did it the hard way. Nothing to remove if you just reach under the pump and push on the tab and rotate the housing.
@MikeFeuer5 жыл бұрын
yes but if you don't remove the basket, rotate it 90 degrees and then put it back together it will be sideways.
@gregHePilots2 жыл бұрын
New pool dad with a recently purchased home with pool. I fucking love you. Thanks.
@MikeFeuer2 жыл бұрын
Ha, glad it helped :)
@bighunter2837 Жыл бұрын
Same situation. Life saver!
@angelsuarez176 жыл бұрын
Very simple. Thanks for the walkthrough.
@daurigl5 жыл бұрын
Thanks Mike! Very helpful!
@MikeFeuer5 жыл бұрын
Great to her it was a help to you :)
@ScottTousley2 жыл бұрын
Thanks! Great video helped installing this for our pool
@MichelleFitchgoomba983 ай бұрын
Hey Mike, is there a seal or o ring between the pump and the union where u attached the filter. Just curious because I have a small drip between the filter and the pump. I sure hope u still check your comments.
@Thirthton3 жыл бұрын
You made it easy... Thank you buddy..
@cindybeal Жыл бұрын
What is the grey stuff you are using? It sounds like dope but I sure can’t find it.
@redneckfarmer6584 Жыл бұрын
Can it be rotated clockwise as well?
@austindickinson82986 жыл бұрын
Thank you very informative. other than my father in law breaking the union inside the hayward ec40ac is there a way to replace just the union ...thank you for the video
@van8cab982 жыл бұрын
Oh man, thank you so much. I have no idea why they don't come with clearer instructions! Life saver!
@paulnowosielski74364 жыл бұрын
Thank you!
@lrayvick3 жыл бұрын
Any opinion about using this pump for an in ground pool?
@unkalicious14002 жыл бұрын
Do most pumps do this? Looking at pumps on the Amazon and just about all of them are shown discharging up.
@MikeFeuer2 жыл бұрын
If the pump doesn’t show that it rotates then I would not assume it does. Hopefully the seller will be able to tell you if you ask ;)
@cancelmycards2 жыл бұрын
Thank you!!!!!!!!!!!!
@shanelevesque89693 жыл бұрын
I don't understand. Do you have to rotate the pump?
@MikeFeuer3 жыл бұрын
No - only if you want to change the configuration to match your setup. If the orientation is good for you then no need to change it.
@goguzman01013 жыл бұрын
Livesafer!!!!
@MikeFeuer2 жыл бұрын
Glad it helped you :)
@miked63352 жыл бұрын
Just curious, why did you remove the basket? Wouldn't it have just turned along with the section you turned. Thanks for pointing out where that tab was. Edit: Well. I followed your video along with the manual and the install went perfectly. I'm guessing that the horseshow clip would have held the basket too tight to turn and that's why it needed to be removed. Don't know how anyone could press that tab down without your screwdriver trick. Thanks again!
@michaelferman14 жыл бұрын
Perfect!! Ive been struggling with this thing for 2 days. Took me about 12 seconds after watching this!! Thank you!!!
@itribute18964 жыл бұрын
Glad to hear it! - I struggled when I first started messing with and decided I needed to make a video to help everyone else struggling :) Really lead it has been of help :)
@juliodavid496 жыл бұрын
Dude I just ordered this pump to replace my old one. I thought I had to remove the impeller cover to rotate the connection. You don't know how thankful I am that you made this video. Thank you, thank you, thank you.
@MikeFeuer5 жыл бұрын
Thank you, I'm glad to hear I've helped you save some grief :)
@MikeFeuer5 жыл бұрын
Really glad it helped - that's exactly why I made the video :)
@dennisseger67175 жыл бұрын
Thank you for a great video- you made it very simple, I did not want to break the pump and this was fantastic!
@MikeFeuer5 жыл бұрын
Really glad it helped you :)
@marmadmax12 ай бұрын
Will the outflow connection ring rotate in either direction or only in the direction shown in the video? Thanks.
@jcnurse Жыл бұрын
Thank you for this video!!! No one was able to help me over the phone with rotation. I called Hayward and the company I bought it from. No one would help!
@MikeFeuer Жыл бұрын
I had the same experience - that is part of why I made the video - really glad it helped
@andreab9192 жыл бұрын
I wonder if you can help me. I have a Hayward matrix power flo 2 speed above ground pool pump and I need to change the switch. Here ia my problem. The back of the pump does not have that cover that comes right out with one screw. Mine has two holes in wich seem to have flat screws. But even if I unscrew these, the back does not pull out. I did not take the screws completely out not knowing if it is ok to do so. Can you help me in telling me exactly how to reach that switch. Thanks.
@hollygigliotti10593 ай бұрын
What size o ring does it take before I clip the c clip on!? I have a leak there
@melchristman4010Ай бұрын
Thanks for your video.
@angelsuarez175 жыл бұрын
Nice walk through.. Thanks
@MikeFeuer5 жыл бұрын
Thanks Angel, Glad it was useful for you :)
@polishbrazil2 жыл бұрын
You save my day, thanks a lot!!
@roadrunner84284 жыл бұрын
I just came across your video and I am glad you did not add teflon thread tape to the male end of the coupler; there is a 2 1/4" rubber seal on the inside of that male end which connects to the female end. Adding teflon tape will not allow the threads to tighten enough against that rubber seal thus causing a minor leak or a larger leak depending on how much tape you wrapped around those threads. Good video on replacing your pump. Cheers.
@MikeFeuer4 жыл бұрын
Thanks for the kind words :)
@alexismcnear64335 жыл бұрын
Thanks for the walk through, It was so easy after watching this video. Man, what was life before KZbin?👍👍 #SUCCESS
@MikeFeuer5 жыл бұрын
Glad you found it helpful :) - All the best
@timmcmanus87133 жыл бұрын
Wow did this help. Like an absolute moron I’m out in yard with that union piece attached to the filter and the center wasn’t turning and I forgot how it went. So I’m cocking the filter sideways as I try to literally screw the pump on and like, it’s heavy and couldn’t get it centered and I said no damn way this is how it’s done🤦🏼♂️
@van8cab982 жыл бұрын
Any chance you could show the full filter installation? Or know of a good source for instructions?
@craig716862 жыл бұрын
Definitely glad I watched this video. It is way easier than I thought. Lol. Thanks.
@kevnalu3 жыл бұрын
Whomever gave thumbs down is an idiot. Solid how-to video. Thanks.
@brendencassidy710 Жыл бұрын
The Union they sent me doesn’t seem to fit the filter thread.. am I missing something?
@MikeFeuer Жыл бұрын
I don’t work for them but if it doesn’t seem to fit then it doesn’t. I would ask for another
@brendencassidy710 Жыл бұрын
@@MikeFeuer turns out they sent the wrong part and I had to buy my own 😂 all Hooked up now, great video!
@gini12943 ай бұрын
No teflon tape?
@MikeFeuer3 ай бұрын
For the union you don’t need tape as it is a compression seal. Tape would not be recommended for this as it may impede the ability to fully tighten down the union.
@samy47155 жыл бұрын
hello my friend how much watts consumes the pump in the std? thanks great video
@armand019722 жыл бұрын
Can I do this with the Hayward power flow lx ?
@lorikelley7042 жыл бұрын
Perfect clear and concise.thank you so much
@AbigailBiz3 жыл бұрын
Does anyone know exactly what union was used ?
@stephanienazar252 жыл бұрын
Exactly what i needed. Thanks!!
@Szeer133 жыл бұрын
Thank you Man. That was very helpful!
@justask56254 жыл бұрын
Does it have to have a union from filter to pump? I bought same motor but new and it had a different fitting than my old motor so unused a hose and clamps....but I'm having zero suction somehow. What is grey stuff u painted on?
@miked63352 жыл бұрын
The grey stuff is Pipe Dope. The manual says not to use it on threaded fittings and use Teflon tape instead. I use Pipe Dope and hose clamps where flexible hoses fit over the tapered fitting (the opposite end of where he 'painted' on the dope) and only have friction to keep them connected.
@srjeff13 жыл бұрын
Thanks for the video.
@VeteransUSA5 жыл бұрын
I have to remove the pump from the mounting plate to change the basket nut the screws are very rusted........any tips on how to remove the pump fro mounting plate?
@MikeFeuer5 жыл бұрын
I'm not sure what mounting plate you mean but If the bolts are really rusty I'd gently tap them with a hammer (Don't tap the threads, only tap the top of the bolt or the nut). Then use a penetrating fluid that you can buy from any hardware store and follow the directions on the label. DON'T force it as you will likely snap the bolts. There are lots of videos on youtube that I'm sure you've already watched... Best of luck with it :)
@dennisseger67175 жыл бұрын
Mike I am unable to lock this in position I do not want to break it- The guy that designed it should be shot- the button should be raised to get to it.Any suggestions? I am trying to gently trying to get it to click but it just will not go!
@MikeFeuer5 жыл бұрын
dennis seger - I’m not sure what to mean won’t lock. Do you mean you already rotated it and at the end of the rotation it is not locking into position? If so rotate it back and see if it will lock in the original position. You can give a pretty good slam into position (not too hard though). If you’re unit is new and is not locking then I’d bring it back to what’s you bought it as it should be working.
@law35penn4 жыл бұрын
Nice, i wanted to do this too.
@shelelol4 жыл бұрын
i can't seem to get the union between the pump and the filter to stop leaking water
@MikeFeuer4 жыл бұрын
SOunds like you may have a scratch or something in the union where the to piece meet - - I'd disassemble and carefully inspect both pieces - even a small defect can cause a leake here.
@jer4284 жыл бұрын
Oh my, thank you so much for this video. What a great help and well explained. Again, thank you so much.
@itribute18964 жыл бұрын
Glad it was of help to you :)
@sherryconner70686 жыл бұрын
I just got this very pump yesterday. Got it installed and it's leaking water at the cap line. So aggravated! Any ideas what might be the problem? Also, I put the proper lube on the O ring too. Thanks in advance.
@MikeFeuer5 жыл бұрын
Do you mean the cap itself is leaking? I'd take a very close look at the o-ring and make sure it is not damaged. If it's in good shape, you have the cap put on correctly and it's leaking then you may have a dud.