It was a broken black wire for me. I found it and connected small piece of wire to it. Then drove my truck for about 15mins and then the check engine soon 💡 turned off🤩😌💆🏽♂️ Thanks Jerry👍🏽👍🏽
@asimlovely9061 Жыл бұрын
There is much difference between to be have good knowledge and ability of transfer knowledge.
@rayray52ful2 жыл бұрын
couldn`t a cacuum leak cause a p0102?
@mikejohnson7768 Жыл бұрын
Cacuum leaks don't happen
@dannyreid18452 жыл бұрын
Are you doing the testing with the key on?
@nesdi6653 Жыл бұрын
Thats what i was wondering
@thealliedspy41708 ай бұрын
Most likely, just make sure to not run down the battery.
@jeremya3754 Жыл бұрын
hey im going thro the same thing here on a 1997 tahoe 5.7 its the same problem in the video i cant find any grounds that are off all fuses are good i even had another computer and tried it did not work put the old computer back in it same problem (P0102 mass or volume air flow A circuit low) and i have a new mass air flow sensor installed the exhaust system is fine. not sure where to look from here.???
@johnvegar90983 жыл бұрын
So how about the other 3 wires on the MAF sensor. I have a reading on the air temp but zero reading on the airflow. Engine runs terrible. I look forward to hearing from you and maybe you can help me get this thing running right
@moyrodriguez43762 жыл бұрын
Hello, one question, I have a 2011 5.3L chevy silverado that has a swap cam it doesn't turn on but if there is a spark and also if there is gasoline in the injectors and the scanner gave me the code p0102 and I already changed the maf sensor and nothing happened and I put the starter fluid in the throttle body too and it didn't start and I saw that the throttle opened very little when I accelerated, what could it be?? And I also checked all the fuses and relays, they are fine
@TestDontguess2 жыл бұрын
Why did you change the sensor what troubleshooting did you do to verify it was bad ?
@vjxpiroevo92633 жыл бұрын
Hi, I have a 05 colorado 3.5 I did all the test but for some reason I dont have signal for the maf wire signal, scanner says maf is 0.20lb/min it doesn't move at all !
@jadkins15082 жыл бұрын
You have a bad ground more than likely
@boostedserg2 жыл бұрын
What maf are you using?
@joesyoutubepage7 ай бұрын
how do ifix this issue
@danhambrick63313 жыл бұрын
Thanks Jerry.It can get expensive firing off that parts cannon.😂😂
@eliaskauffmann47733 жыл бұрын
That's a bad ass swap💯
@RENEM19863 ай бұрын
Connector has to wiggled around to get data !
@romie4263 жыл бұрын
My car won’t start and it’s throwing that code. I replaced the maf sensor and it’s still won’t start. Was running great the other night, came out yesterday morning and it’s trying to turn over, I just won’t start. I’m at a loss lol
@manolilinas56022 жыл бұрын
you figure it out yet?
@antonchigurh54722 жыл бұрын
Mine does the same thing, it runs without the MAF sensor. Replaced the sensor and still same shit.
@nesdi6653 Жыл бұрын
@@antonchigurh5472 i have a 2011 prius i replaced the MAF its still tunning horrible and shutting itself off. loss of power Try running the engine and disconnect the MAF My engine runs smooth for like 1 second when i disconnect the MAF then goes back to running horrible
@JasonJASniper5 ай бұрын
@antonchigurh5472 yall figure it out. I know been a year but damn bro I replaced maf cause when it's unplugged it runs but plugged in it just stalls
@spacejunky43802 жыл бұрын
Hey, I know this is super late comment, but someone might see it. I have a problem with my MAF sensor, go figure right. I replaced the sensor and ran another SMOG test to reasses the issue. O2 sensor pops up along with OBD EXG- which can be many things, I reseated the sensor and drove the car for about 30ish miles and my check engine light, "service soon" bs on my dash. I don't know what the hell is going on now. Before, the light was off, and no its on again. All I want is to pass SMOG lol, if someone who is more knowledgeable help me figure this out I am more than willing to remove, replace, or fix anything wrong. I love this car, it sounds amazing, just want to get plates on it thx