John Deere 567 and newer netwrap adjustments

[@mdhavard1706]

Can’t thank you enough you saved me a lot.The bolts came out of the box letting it shift forward. I was about to lose my mind. It’s not fun when your net is not operating correctly. Thanks

[@joesanchez4895]

Thank you so much for posting this video. You have been most helpful, I have ran a baler for years , Always used twine , This fall the straw needed net wrap. I had no idea how this system worked . The updates u have shown me Will save future down time. Great idea with the brush , It is nothing but a dirt collector. You got me up and running again after I watched your explanation!! Thanks again so much for your time to post this!! You rock!!!!!!!

[@prairierose385]

Good morning. I started having an E4 02 code popping up on our JD 569 baler. After trying to find the problem, I ran across your video. You pointed out numerous areas that could be problematic. I’m going to do a thorough check and hopefully will get back to running soon. Thanks again for a a very detailed and helpful video!

[@jeffqueen3790]

Thank you. Got my 568 going!!

[@Jump2218]

Good to know! I recently purchased a new baler that has net wrap and I had no idea how it worked. Your video has pointed out things I need to keep an eye on. Thank you!

[@ericbutler2733]

Really helpful. I added the kit to my 567 baler, what a difference. Thanks Jon!!!

[@masseyranch]

Great video! Thank you for sharing your knowledge!

[@piperdoug428]

awesome tutorial, i bought a decent 568 and it's not cutting off the net to finish the bale n leaves tails, this should get her fixed

[@LifeByTheHorns15]

Awesome Info Sir! Thank you!

[@MoweryFamilyFarms]

Where do you get the spacers for edge to edge

[@markwillis2762]

Very knowledgeable and detailed. Turn your phone sideways.

[@haycountry117]

I just bought a 467 Baler and want to run edge to edge and it don’t have the kit installed. Is that kit pretty easy to install and do you think I’ll need it? Thanks

[@IHJonny]

The wrap roll will need the spacers, I tried on my baler to not add the wider sensor pad kit and it would say the wrap didn't go on bale more times than not, so I added the kit, you can try and see if it works without and go from there, it'll wrap bale but just error out after wrap cycle if net didn't hit sensor pad, new pad is only a inch or 2 wider and also has the stopper to keep the switch arm from being bent

[@haycountry117]

Jon's Repair thanks so does that wide pad just slide off. Hard to tell in video or do you have to disassemble some things to get to it.

[@mattbest1571]

Hi mate do you know how to retract net actulator? Mine wont come out of drive and go home, any ideas?

[@taylormaahs9495]

Hi it sounds like you kinda know a lot about these balers I just purchased a 2001 jd 567 baler it’s the combo net wrap or twine and we started using it and when it goes to net wrap the bale for some reason it doesn’t want to disengage after the 2 rounds of wrap are complete, so it just keeps wrapping what would be causing that ? We checked the actuator and switch and all have the correct voltage and what not so just trying to figure out why it’s doing that if you have any advice that’d be very appreciated

[@jessesabatka4314]

I'm having the exact same issue, to the T, we're you able to figure anything out? I've got good voltage, I've tested the actuator manually with a battery and it works great. Won't disengage after the net warp cycle and just keeps wrapping. Have you figures out your issue?

[@keenansimmons7695]

Hey Jon, have you ever experienced the net actuator not resetting?

[@mdhavard1706]

I had that problem drove me nuts. JD came out numerous times. Ends up they say it was a bad ground. That’s just my experience with it.