How to program your Garage Door keypad clicker opener! - Chamberlain Klik2U

[@mrugeshmistry]

This is not working at all

[@jackdelehey]

This video right here is amazing. Everything I needed. Way better than a manual. Thanks Danny!

[@DannyPops]

Thanks for the comment jack! I too was sick of bad videos and manuals explaining this.

[@leeclutter3296]

Yes, my thoughts exactly. Thanks Danny. The Clicker is working again.

[@liftacar]

Great guide and I followed it to a T however when I set my code (ex: 1234) then when I go to type it in the garage opens after i just hit the 1. I've reset it about a hundred times now and can't figure why this is happening. Any idea how I can fix this? I have a Genie Pro Screw Drive garage

[@mrknumbskull]

I just did mine. After following the directions I went to key in the code to test it and it closed after hitting the first number. I then entered the code like normal and it worked. Don't know why.

[@kylevance3043]

⁠@@mrknumbskullafter resetting, do you need to hit # or anything after your new password to open/close? I just test mine, got it to close (it also closed after the first number), but now I can’t get it back up with my new password…?

[@3DJubilee]

Thank you for sharing this. The only clear explanation I could find anywhere! Has it working in a couple of minutes

[@Sonshineglory]

Thanks for adding the code sheet. Very helpful.

[@Mr5150guy]

Thank you very much! Somehow mine had become deprogrammed. The garage door unit still remembered it as a remote, but somehow the pin did not work until I re-programmed as you instructed. Thank you again.

[@paulettesharkey4881]

Thank you, Danny! My husband and I had been messing around for hours trying to figure out what garage door opener TYPE we have (the manual didn't tell us). Then we found your video, used the chart to find what we needed, and programmed our clicker in minutes.

[@sepinac]

Excellent and very simple instructions! Worked right away. Thank you!

[@guhanswaminathan3422]

Awesome explanation! It was so easy I found my code from the quick screen grab you showed of manual

[@str8fromtheword850]

Thanks!! Works as explained! Saves me money on buying a clicker in Car for now lol

[@wkkoch389]

Fantastic video, you kept it short and sweet. More helpful than the manual.

[@aimees4621]

Ohhhh my god! THANK YOU!!!! Bought a house with this crappy keypad and no manual. Everything I found kept saying to hit the Enter button. THERE IS NO ENTER BUTTON!!! Thank you for saving me from taking a hammer to this stupid thing!😂 🔨💪🏼

[@UpGreyeDD]

Thank you very much! Worked perfectly.

[@stjabnful]

Thanks so much! We didn’t know our brand- kinda. So after a process of elimination on 4 tries- yeah we got it!😅

[@genehenning8144]

Thank you very much I was getting frustrated, Now it works!

[@alexanderwimbly801]

Thank You @Danny Pop! Straight to the point this is exactly what I needed.

[@vanwahlgren8451]

Thank you Danny especially for putting in the garage door type.

[@Rcarhar]

Now it opens and closes with any key. I hate this thing

[@kenarnold8822]

easy peasy....thanks for the quick help. Took 30 seconds!

[@lawharrell49]

My man!!! Thank you.

[@larrywalden626]

It worked for me just fine. Thank you. I have a overhead garage door opener. Specifically model 2026. I had trouble trying to find the right ID for it. It's number 6 for those that have trouble finding it.

[@JohnJohnCrusher]

0 is the "enter" key. Gee why didn't I just instinctively know that? No "program" button, no dedicated "enter" button. Who designed this thing? Thank you!

[@waynebell3452]

Great videol but I have a question......I installed the same keypad controller you show and it works great. But, now my portable garage door clicker that I keep in my car does not work. Do you have a fix so that both will work?

[@vascoernesto78]

I followed all the steps, light blinks, meaning I should be good. Then I enter my code but nothing happens🙄 UPDATE: now it turns out that any key opens and closes the door and I can no longer reset it because the star and pound button also open and close the door

[@michaelvidmar2042]

Thank you! The key was showing the list of garage door openers. Excellent instructions.

[@stevedowns5049]

Thank you. You are the only one that helped me with garage opener code.

[@DannyPops]

You are welcome! All the videos I saw were confusing so I made this one.

[@ericl29]

Fantastic video. Thank you. It was easy to follow and worked the 1st time for me!

[@amistrat1]

Thank you for this video and especially the color codes which were very helpful.

[@kimloanla2382]

I got it right to the part hit the learner then enter new codes hit 0 , nothing happened, no light flashing.

[@marc-andreguerin4723]

you make my day my stupid Clicker run :) Thank'S

[@johnschadegg152]

This is the best video out there for this because he displays the different garage door opener I'd codes. I couldn't find those anywhere. Thank you very much!

[@DannyPops]

It was born out of having to figure this all out too

[@andrewparkerMD]

Life saver! THANK YOU!

[@shifttransformations6597]

Thank you for your video you helped me greatly God bless

[@LeiZhang-c6m]

What should I do if my keypad not blink when I hold *and # and same time ?

[@vuhoang7109]

Quik to the point and effective!!! Thank you!!😁

[@neilmurphy4178]

Thank you . . . Simple and exact. Done programming 2 openers and one keypad in 5 minutes.

[@christinahurlbutmontoya15]

How did you program 2 doors with one keypad? I’m at a loss!

[@janlesko212]

I've been trying this for 40 minutes. Didn't work. Then I decided to replace the battery...THANK YOU! 😊

[@claudiac577]

Thanks and I like that you are channelling Ferris Bueller at the end. Hehehe. Oh and I see you are in New Mexico! Awesome I lived in SF for 7 years

[@MyJesusSavior]

Thank you very much, It really helps.

[@trekkin_fpv5272]

What a terrible device, but the video is ::chefs kiss::

[@fasttruck9177]

Thank you thank you thank you! Great video especially that my lift master was code 2, no searching for it. Well don’t!

[@anthonysparaccio5057]

Thank you so much for this video, after reading manuals and watching different KZbin videos, yours was the onky one that actually helped me. All the ither videos were saying the same thing over and over.

[@brendanquinn8433]

What does it mean when after I successfully enter my code, the numbers remain highlighted and pressing any number will open or close the door?

[@michaelbrame4933]

I looked at serval videos you had complete and basic instructions. Thank you.!

[@busternsam]

FINALLY…. Thanks for flashing up the garage door opener type. You’re right these are stupid.

[@Lmnop168]

Works perfectly, identifying the garage ID is most crucial. Thank you!

[@BattleBornGunBrokers]

Great video! I never would have figured that dumb thing out without this video! Thanks, Danny!

[@lvsurfcat8584]

I've got the same setup older opener also red botton, good that you have an i.d chart for the rest that have a different opener, thank you !!

[@stevebrown2848]

Thanks for this. The provided instructions are woefully inadequate.

[@UltraEgo09]

Mine keeps setting my code as 3 (my garage code to reset) and I’m not sure why? I’m doing everything exactly as it says in the video

[@arok2606]

Wow thank you for actually providing the code numbers, nobody else did that in their video

[@ferozkarjikar4829]

Everything you need to know, crucial part was to find the type of garage door and its ID - Manual link helped. Thanks Danny!

[@cats.crafts.cookie]

I can't get mine to wrk. Could it b I need a new battery. I tried all the different type codes too. Wth.

[@djleodiandrade]

Thank you so much Danny ! This was Drive me crazy !!! 👏🏻👏🏻👏🏻👏🏻

[@2wayty]

Thank you Danny! This video is on point. Super easy to program my garage door now. Thanks again.

[@dih706]

Worked where other instructions online and videos did not!!! Thank You Danny :))

[@paulcollins7385]

Thanks Danny! My KLIK2U is back working again thanks to you,

[@F.a.i.t.h.speaks]

Omg, this worked!!! It took me two tries but I got it. Thanks soooo much!

[@SharonFlicker]

so helpful! thank you!!!

[@orbit_gary]

Great video Danny. Thanks for the very helpful code table too.

[@alecgoenner]

This is the most helpful video on this. Your the only one who posted the codes and manual for the garage door opener.

[@emilianopadron20]

Thank you it was quick and thanks to you having that manual on the side big help thanks again

[@Frank2314-y1z]

Ty friend you are the man I did exactly what you said and it worked

[@fyafeelings3976]

You da man! Worked for me!! Mine is a yellow button code number 8

[@jstylephotography]

Amazing chamerblain opener purple button is #3

[@rashellecirigliano5467]

Awesome information so kind of you to take the time to educate us on this confusing item

[@timhaeussler-yp6qr]

Thanks for providing the opener codes mine was a 2 also.

[@jamello29]

Thank you, this is exactly what I needed!

[@wam4985]

Best video thanks for including the codes!!!

[@theflashbackchannel6199]

Great video, but I could not get it to work with my green button Craftsman (ID 4). Don't know what I am doing wrong - could it be because my keypad is a plain "Clicker", and not a "2U"? Mine sure looks like the one in the video...

[@DannyPops]

I wouldn't put it past them to have a completely disparate system for a slight model difference. Sorry you couldn't get it working.

[@theflashbackchannel6199]

I took the keypad off the wall and there is a sticker on the back saying that it is a model KLIK2U-P2.

[@ursalynnhardin3960]

Now the clicker isn’t working

[@gbaldus67]

Saved me an hour of my life!!!!

[@CraigHofer1]

Thank you. Very helpful.

[@mohitkaushik1970]

Very helpful thank you!!

[@jlBoucher]

The keypad with no enter key is absurd but this video was just what i needed. Thank you very much!!!!!

[@MRHUBE2010]

Out here doing the lords work. Thanks

[@joeschengrund6886]

Finally, a tutorial by a guy from this era.

[@DannyPops]

Lol thats how I felt looking for videos on this too originally

[@adrdapps7787]

👍' for showing manual

[@DrZzen]

Great idea to show the garage opener ID number in your video. Exactly what I was missing. Thank you.

[@Ryan-zm2nr]

whats the id good for?

[@yamilethandre9884]

Great video. Worked for me

[@GeeTay707]

Wow amazing I can’t wait to try this 2mrw I will let you know if this works :) ….. 11/3/2022

[@DannyPops]

Should be easy! Let me know if there's any issues.

[@mebarnes100]

Thank you so much for the help!

[@TryorDie2024]

THANK YOU VERY MUCH

[@mattbessette9589]

I did all your steps and it worked as you said until the end. When I push 1 button the door opens/closes. I dont even get to enter my full code. Any suggestions?

[@mariahschaaf8640]

I have the same issue!! Hope you get an answer so I can try to fix mine too!

[@UltraEgo09]

Okay I was having this problem and this is where I went wrong - the 0 you hit at the end of you code will now be a part of your code so if you chose 1234 your code is actually 12340 and for about 20 or so seconds after programming it any number on the keypad will open/close the door. Some openers also require you to hit 0 twice. So following the instructions and after hitting the learn button - put in your code - hit 0 then hit 0 again. That may help. It helped me

[@liftacar]

@@UltraEgo09 I'm having the same issue. Tried both of these and it didn't help. When I put the first # of my code it opens the garage door. I have a Genie Pro Screwdriver

[@UltraEgo09]

@@liftacar give us like 20 minutes after you do it. Like I said some openers will open the door when you hit any number after setting it for like 15 -20 minutes. If that doesn’t work I’m not sure. This is just what worked for me

[@liftacar]

@@UltraEgo09 First of all, you're amazing for replying so fast and i love you. Secondly, 20 minutes? lol, I thought you said 20 seconds in your previous post which I gave it 20 seconds and it still happened.

[@AaronStrawn]

Perfect!! Thank you!

[@paulkelly3973]

I need to buy this man a beverage.

[@bgaliant]

Thanks! Worked like a charm

[@PaulaNowling]

Thank you ❤️❤️❤️

[@COLOMBO05]

Thank u.

[@reginabroughton5917]

Thank you..

[@shaundaniel4693]

Thanks bro

[@tgr.4550]

If you hire someone to do this, how much is a fair price?

[@DannyPops]

Hmmm I mean its pretty simple but at least $20 bucks for an hour of their time

[@tgr.4550]

@@DannyPops That seems fair. From what I see in the video, it should only take a few minutes.

[@damnyankeefl]

Thank you

[@taunagregory4415]

Best post so far. Thank thank you

[@rylangray5785]

Thanks for the help!

[@larryfuentes2481]

Thank You.... Thank You....😀

[@mac2920]

Excellent video!

[@Jake.schriver88]

Heck ya thank you

[@mikem6213]

SUPER!!! Thanks much!!!

[@MsDonnnG]

So helpful! And I share the same sentiments about this garage door opener!! Thanks for posting!!