CWB Stick 7018 Horizontal Canada welding/아크(전기) 캐나다 수평 CWB용접

[@liveroughly787]

이런훌륭한 채널이있다는것에감사합니다3~~~^^

[@kimchiwelder8410]

시청해 주셔서 감사합니다! 더 좋은 영상 올리도록 노력하겠습니다.👍👍😁😁

[@johncaines4496]

Most helpful video for CWB 2G out there thank you very much 😊 🙏

[@kimchiwelder8410]

thanks for watching!👍👍

[@Hood_Tyme_Fab]

Love your videos pal I'm not really a stick welder, but there's something about it over MIG and TIG, I use it at every opportunity.

[@황배추된장국]

Kimch! 감사합니다.!

[@Gigaweld]

Nice job. Who does film you? How do you film, camera inside welding helmet?

[@amilaudayanga1878]

Nice demonstration, thanks.

[@NoahPARK82]

I like how you stop at the run off tab

[@kimchiwelder8410]

thanks for watching! 😎😎

[@존존-x1z]

잘 봤습니다 실력이 대단하셔서 용접 유투브로 대성하실겁니다!! 다음번엔 tig 용접 cwb시험 하는거 보고싶네요^^

[@kimchiwelder8410]

감사합니다!, 물론입니다. 티그로도 CWB포지션을 포함한 모든 포지션을 영상에 담아서 빠른시일에 올릴수 있도록 노력하겠습니다!😎😎

[@BathSaltBadger]

I'm so confused, I thought the first pass is a straight through for horizontal on fillet side (90 degree). 2nd Pass is the stop at 2/3 (beveled 30 degree) and then restart.

[@kimchiwelder8410]

Hi Thanks for leaving a comment! I don't know if the CWB exam is a little different depending on the region or the inspector, but this time my CWB ticket has been renewed after 2 years. First pass was the stop at 2/3(90 dgree), and second pass was the stop at 1/3(30 degree). But before the test, the inspector will explain and start the test, so it will be most accurate.🔥🔥🔥

[@BathSaltBadger]

@@kimchiwelder8410 awesome! Thanks man

[@kimchiwelder8410]

@@BathSaltBadger no problem😎😎

[@manonenejian9860]

Thank you for the video How I avoid undercut ??

[@kimchiwelder8410]

Hello, mano! Make sure to adjust the angle of the welding rod to the left, right and up, down short arc distance and staying time🔥🔥 thanks for watching!😎😎

[@sharonbalus3236]

Shoutawt too you idol thank you for this video

[@NkosikhonaPhungula]

What is your roots run amps

[@MegaJESUSALBERTO]

Nice job men, congratulation

[@kimchiwelder8410]

thanks for watching 👍

[@덕주하]

잘하네

[@kimchiwelder8410]

좋게 봐주셔서 감사합니다😁😁

[@robynnlove]

Do you ever do pipe welding? I just took a 6G TSSA test. Didn't have much time to practice. Any help would be great. Thanks for all your videos!

[@kimchiwelder8410]

Hello, Robynn! There are many pipe welding videos on my video list.👍 I believe there is a video that will help you!😁 Thanks for watching!😎😎

[@Kopetgondol]

Good job

[@apacher3335]

What did you have your amperage set at?

[@renanstreetsk8]

Looking good! Nice video!

[@kimchiwelder8410]

Thanks for watching. I will always try to make the video more informative.😎😎

[@dirtyhtv]

At what angle do you need to hold your electrode?

[@kimchiwelder8410]

I don't know the exact angle, but I think it's about 100-110 degrees. However, it's more important to remember the welding puddle from the video than to value the angle. thanks for watching! 😎😎

[@dirtyhtv]

@@kimchiwelder8410 ok

[@markalbert9965]

Amps?

[@nayanbarua9670]

How use the size electrode?

[@cesarmorga5566]

How many amperage

[@kimchiwelder8410]

Hello! 120~130 for horizontal position! Thanks for watching! 😎😎

[@matan7668]

Yooo Kimchi this is so good

[@matan7668]

What's your Amp at

[@kimchiwelder8410]

@@matan7668 thanks man! i like 130amps for horizontal. 115~130 is also good. thanks for watching😎😎

[@matan7668]

@@kimchiwelder8410 your videography is great 👍

[@kimchiwelder8410]

@@matan7668 thanks😎😎

[@felireta9179]

Nice!!!!

[@kimchiwelder8410]

Thanks for watching! 😎😎

[@weldzanofabs8660]

how long have you been welding?

[@kimchiwelder8410]

10yrs

[@demycapuz2831]

2GF perfect

[@kimchiwelder8410]

Thanks, demy capuz😁👍👍

[@demycapuz2831]

Thank's for your videos 1gf,2gf,3gf pass but my 4gf fucked up😂, Lincoln 100 amps is to hard for me

[@adamstreefkerk6367]

What's the rod angle?

[@kimchiwelder8410]

thanks for watching. Between 45 and 60 for Root~Fill.

[@jamesc5256]

​@@kimchiwelder8410 파이널은 몇도 정도로 하면 될까요?

[@MarketMav7]

No need to stop and start on top bevel only one on the fillet side and you can use a wire wheel grinder but note no grinding discs or file allowed

[@bhbang8122]

영상 잘봤습니다 저도 cwb준비중인데 도움이 되네요^^ 혹시 영상 찍으실때 면안에 넣는 카메라 어떤거 쓰시나요??

[@kimchiwelder8410]

감사합니다, 면안에 본체를 넣는건 몇가지문제가 있어서 아는 지인이 도움을 줘서 렌즈만을 빼내서 사용중입니다.😎😎

[@sevenslab]

You've really got to learn to clean those welds. Your second fill passes were covered in slag. There's no way this passed the bend test.

[@tylertelford2145]

The stop is supposed to be on the beveled side not the square side

[@motleywelder]

You are wrong. There is only one tie in on the top bevel side

[@kimchiwelder8410]

Hi, motleywelder! Thank you for your comments.👍 It's been a long time since I took the CWB test, so I might be mistaken as you said. I'll find out more precisely and prepare a better CWB video.🔥 If there are any mistakes in other videos, please let me know in the comments thank you for watching! 😎😎