Finally, a real man and a real DIY fixer! Thank you for no music abusing my ears. Thank you for getting straight to the point with no preamble, and no talk. Thank you for the natural sounds of tools and kids, and daily life, So soothing. Thank you for great photography and clear audio - yes the sound of clicking and clacking is informative. Thank you for your excellent mechanical skills where I learned something. Thank you for saving my son's $1000+ espresso machine so I could use it!
@annazasheva84052 жыл бұрын
Thank you for the video! My husband wanted to buy a new coffee machine, but I decided to fix our Krups and your step-by-step guide helped me fix the problem 💪
@MisayGoesToSweden10 ай бұрын
thanks for the video .. I accidentally pour water on my coffee beans and it makes my krups grinder stocked up with wet coffee.. I thought I will never use it again..then I saw your video and I fix my krups pisa.. its working great now!
@jornarelolland83234 ай бұрын
Thank you for the video. It fixed my problem :-)
@sarpijk Жыл бұрын
Thanks man! I read your comment about replacing the piston if the coffee is weak! I did that and it fixed the problem of weak coffee!
@anaab16 жыл бұрын
This video is perfect!!! I followed along exactly and now my machine works great. Thank you!!!!!!
@markscharringa8 жыл бұрын
Thank you!! Just saved me buying a new machine!
@golagha117 жыл бұрын
Thanks M8, you saved me for a service visit and probably also a lot of expenses. I am not sure if the KRUPS service department is as happy as me. LOL. Thanks again.
@axelb.20845 жыл бұрын
Thank you very much for your video, Mariusz. It was a great help for me (especially for opening the case).
@cljamming8 жыл бұрын
Perfect! My Krups EA8250 was reading "Filling of the machine necessary Press OK" and then ""Filling of the machine in process". Krups customer service didn't know what to do... Thank you from Los Angeles!! Coffee for everyone!
@MrRulas8 жыл бұрын
Did you fix it? Mine is in a never-ending loop, just passing hot water and asking for "Filling of the machine necessary Press OK" :(
@cljamming8 жыл бұрын
it fixed it for about 4-5 days, then it went back to the ""Filling of the machine in process". I don't know if it's an issue with the electrical board or what. I gave it a thorough cleaning (top portion of machine w/grinder, compressor, ejector etc) and it worked, so I thought that must be it. Then 4 days later same thing again. I'd like to go deeper into the machine and see, but it has fallen low on my to do list. Now I make coffee by hand every morning for the last 5 months. Any luck yourself Raul? Any thoughts on this Mariusz Grden? Thanks for the great videos!
@cljamming8 жыл бұрын
Raul, I called customer service the first time this happened about a year ago, and they said something very similar to what Mariusz replied below (that it may be the magnetic float in the unit where the water tank rests against). I'm going to give this a try! I'm posting the question and Mariusz's response below: ------------ Maria Teresa Seco Garcia 3 months ago Hello, my machine is always performing the autotest, asking for water refill, could you help me? i would be very grateful, thank you very much ------------ Mariusz Grden 3 months ago Hi there, it looks like problem with the sink float or something with the float level sensor (inside the coffee machine - to see it, you have to disassembly the machine). If it is the float swims well, you have to just disassemble the machine (this biggest black cover), and bend the sensor a bit closer to the float. Maybe the float is not totally sink yet, but is right on the edge. I will try to capture a short video with description how to dry the float. But in general - to dry the float, you have to put the entire tank into the microwave. Microwaves works only on water (only on wet things). So after one minute baking (not longer to do not heat to much to do not damage plastic tank. So put the tank into the microwave for a minute, take out and wait until it cools down and repeat it until the float will become totally dry (each time you can dry the float with the napkin). I hope it is your only problem, because there is no error message that will mark something specific. Problem is not that obvious. The only path we can follow is this message with the empty water tank. Fingers crossed \Mariusz
@BackboneNF7 жыл бұрын
Thanks this helped me a lot to repair my Krups xp
@xxkxmx6 жыл бұрын
Dzięki filmik pomógł i expres działa jak nowy ;)
@jakpotten8 жыл бұрын
Thank you so much! You just saved me and my family about 100 £!
@tongfelix36568 жыл бұрын
Thank you very much!!! Now I can do the clean up.🙇🙇🙇
@warrior_of_kastamonu3738 Жыл бұрын
The video i was looking for, much appreciated 👍👍😀
@yvrman19643 жыл бұрын
Thank you, thank you, thank you! You just made my $50 investment so worth it!
@neilwarren7924 жыл бұрын
Many thanks, Mariusz. Your videos have added years to the life of our machine! The grinder cleanup was more important than I realized after replacing the piston. It now works perfectly once again. Clean the very back of the drain? tray the cups sit on to fill. There was a coffee gound buildup there preventing it from clipping in causing water to leak from the front. Also use canned air, toothpicks on the coffee chute, toothbrush and vacuum. No oily beans!!! It likes Lavazza Gold.
@victorbode54002 жыл бұрын
I dont mean to be so offtopic but does any of you know of a trick to get back into an instagram account?? I was stupid lost my account password. I would appreciate any tips you can offer me!
@ansonzakai20622 жыл бұрын
@Victor Bode instablaster :)
@victorbode54002 жыл бұрын
@Anson Zakai thanks so much for your reply. I found the site thru google and Im in the hacking process atm. Seems to take a while so I will reply here later with my results.
@victorbode54002 жыл бұрын
@Anson Zakai It did the trick and I finally got access to my account again. I'm so happy:D Thanks so much, you really help me out!
@ansonzakai20622 жыл бұрын
@Victor Bode Glad I could help xD
@stephenmcpherson16325 жыл бұрын
Agree with Dan - Shop vac is very helpful. Also if you have an compressed air to blow it out a bit (gently) that's helpful; but use the air outside or you get coffee dust in the kitchen :)
@ellasiroskey19628 жыл бұрын
This is awesome! Thanks!
@filipmichalko8423 жыл бұрын
Thank u buddy, now I can enjoy my coffee again! :)
@jomecaar8 жыл бұрын
Thank you so much my friend You are the best Best regards
@handleitnow3 жыл бұрын
Thanks, awesome video!
@rodolpheriera41527 жыл бұрын
thx you save my life... coffee!!!
@user-xl2ls2cm3m4 ай бұрын
спасибо актуально , помог 😅😅😅😅😅😅👍👍👍👍👍👍
@BZee-df8qn7 жыл бұрын
Hey Mariusz,,my Krups EA82 stopped working,I just followed your 'grinder cleanup" video and everything just works perfect,we can enjoy good espresso thaks to you,, dzieki,,,,,Zbyszek
@anaab15 жыл бұрын
Best video on KZbin!
@jpf36222 жыл бұрын
Great Video. Thanks a lot
@barboradudova27648 жыл бұрын
Thank you very much ! You are super !
@shadowplay9925 жыл бұрын
Thank you sir! I used a vacuum cleaner as well ^^
@justinnitsuj70414 жыл бұрын
and how could one not if already "in there"? lol
@gyvulysa20004 жыл бұрын
Thanks, my coffe machine works again.
@kermitthefrog36855 жыл бұрын
Thank you!!! I was abut to give up on removing the top cover
@workandworkhere3 жыл бұрын
Yes me too, it's very hard
@ZordanFuxfell3 жыл бұрын
Thanks a lot!
@93Bananaphone936 жыл бұрын
super dzieki!
@CosmeBustos5 жыл бұрын
Thanks you a lot :)
@roberther11923 жыл бұрын
dziękuje MISTRZU
@altligist53242 жыл бұрын
Vielen Dank, ich habe es mit deiner Hilfe reinigen können
@adrianzygmanski95063 жыл бұрын
Dzięki 💪
@Dilbertic7 жыл бұрын
Hi Mariusz, I have a 8150 and your video helped me take a part the unit and clean up a clogged grinder. I had it all cleaned up and ready to go but now I don't get much liquid when making a cup and a loud POP afterwards and grinds fly all over. Maybe I need to adjust the amount of grind? Not sure how to adjust the grinder? Thanks for any help
@Tsubasalwh5 жыл бұрын
thank you!!)))
@HanzelikR Жыл бұрын
I used a flat screw driver to loosen the compacted coffee grounds, and an air compressor to blow out the debris.
@stevebauer456 жыл бұрын
thx 👍
@sofrontudor73812 жыл бұрын
Hello- first, thanks for the helpful videos. I have a question - in order to set an automatic EA 89xx Krups grinder to grind a bit more fine, the dial at minute 3:23- 3:25 has to be turned clockwise 1-2 positions (compared to the original), in order for the knives to be closer to each other, is that correct? Also, do you know - is there a grinder time setting (or a service menu) for the EA 89 automatic machine? Thans a lot!
@SladjanBizic6 жыл бұрын
Hi Mariusz. Thank you so much for your videos. I have xp7200. Is there any way to force descaling process. My XP never signal descaling. Thanks in advance!
@alexane9997 жыл бұрын
Hi Mariusz! How I can to force cleaning cycle on my KRUPS EA8105 (before 300 cycles as usual)?Thank You in advance, Alex
@mastering3347 жыл бұрын
Cześć Mariusz ! Czy jest gdzieś w sieci filmik z instrukcją jak wymienić wyrzutnik kawy ? Zdemontowałem już młynek ale nie wiem czy po odkręceniu dolnej śruby , ślimak młynka pójdzie do góry . Za odpowiedź z góry dziękuję.
@noftal3 жыл бұрын
Hi, when do you think this grinder should be cleaned the way you show it?
@nelsonmota10 ай бұрын
Hola! Mi maquina no sale cafe pero con la Circulación de agua limpia si! Sera q tiene mucho tiempo de moajem el cafe! Sale mui prensado? Gracias
@fernandoquintavalle51973 жыл бұрын
Tenho uma máquina igual e o moinho do café parece que encravou e agora não moi o grão de café, que fazer?
@piotrkociub6705 жыл бұрын
uszczelka cremy a dolny kociołek zaparzacza, czesc Mariusz, mam jeszcze parę pytan, i od razu z góry dziekuje za kazdą Twoją cenną wskazówkę: --1. jutro zamontuje nowy tloczek zaparzacza z nowa uszczelka "CREMY" - to powinno rozwiązać problem tzw. "kawy lurowatej" bez szlachetnej pianki... --2. jaką TY masz ustawioną w swoim KRUPSIE długosc czasu mielenia pracy młynka ? -- ja mam na fabrycznej pozycji nr 2.... czy warto to zmienic ? na jakiej pozycji TY masz ustawione ? -- 3. postaram sie tez ustawic mlynek nieco mniej agresywnie, teraz po zaparzeniu w dolnym kociolku zostaje troche resztek zmielonej kawy, szybciej zapycha sie ekspres niestety :/ --4. czy w dolnym nierdzewnym kociołku zaparzacza kawy tez jest uszczelka, którą należy wymienic? , czy tylko w górnym tłoczku jest uszczelka tzw. "CREMY" i tylko to warto wymienic ? z góry dziekuje za Twoje odpowiedzi.... pozdrawiam piotr
@macgyverPOL4 жыл бұрын
Cześć. Czy da się do tego ekspresu wgrać inny Soft? Albo czy da się wyłączyć opcję aby się nie wyświetlał komunikat o płukanie przy każdej kawie...
@mailineromon36728 жыл бұрын
merci
@johnger8 жыл бұрын
help, a have Krups EA8255 Potencia 1450W and in lcd this mistake 5, what is this?? I need technical manual
@Soysarah157 жыл бұрын
y cuantas pastillas se usan??????
@alekseimyroniuk70937 жыл бұрын
Hi Mariusz, thank you for your kindness and expertise. My grinder runs much slower than it use to. It seems to struggle no matter what setting I put it to...fine or course. Because its running slower that causes the grinds to get stuck it the plastic wheel that feeds the shoot. When If the coffee doesn't make it down the shoot to the chamber that causes the machine to leak because there is no coffee to absorb the water. Is it possible the motor that runs the grinder is on its last legs? Will motors loose their power as they ware? Krups EA827E
@MariuszGrden7 жыл бұрын
I'm sorry I see such problem first time.I don't think that it is caused by the motor. More because of the jam inside or (what is worst) the elecronic board.. \Mariusz
@alekseimyroniuk70937 жыл бұрын
Thank you Mariusz. Your response and time is appreciated. All the best.
@antonioguimaraes44113 жыл бұрын
Awesome! I have a EA815050 and love it. Where can I get the screwdriver with the special tip you are using? and what is the model or part number for the screwdriver? that is all I need. Any info is deeply appreciated. Thanks.
@AnaSilva-tb5pc2 жыл бұрын
Tork 10 :) just got mine fixed
@franekw52742 жыл бұрын
A jak wymienić wyrzutnik do zmielonej kawy ten plastikowy pod dolnym żarnem w Krupsie EA8260?
@AndresRodriguez-ux4tr3 жыл бұрын
Hola. Se me sale el café por algún sitio, la desmonté y no veo avería. Me puede ayudar? Gracias
@otakarhamalcik11077 жыл бұрын
Hi Mariusz, thanks for nice video. I have older model I one I try to opened my self but I can get just to grinder. It has stone jam between stones. Twice the mashine has sevrice but the is alvays leaking water while is in operation. What you thing is a problem. There is so many o rings. Can be a specific what I need to look at it. Thanks Otas
@MariuszGrden7 жыл бұрын
Hi, there is only a few gaskets to replace and it is a good practice, to replace them all - than your machine will have full maintenance so will be like a new. Full set of needed gaskets cost about 20$ so it is worth this price. It is hard to judge which one cause a problem. However I'm sure that when you replace all of them, you will get rid of any problems for next ~two years. \Mariusz
@DroneMasterFilmariAeriene7 жыл бұрын
+Mariusz Grden, thanks for your time spent in doing these videos for free! I have an issue... regardless of type of coffee I grind (I tried 10+ types), all of them taste bad, all the same bad smell. I used cleaning tablets twice so far, in less than a year without noticeable results. Please advise what can be done. Thanks! Marius C.
@MariuszGrden7 жыл бұрын
Hi, three things you can do: 1. I strongly recommend to change entire piston. It costs the same as just two piston gaskets, but inside of the piston there is one additional gasket that is not available standalone on the market. It is called "cremy" gasket and is responsible for coffee strength and taste. This gasket has microscopic puncture inside and brewed coffee is pressed with high pressure through. With the time being the puncture is bigger and bigger so coffee just leaking through instead being pressed. 2. regulate the grinder to ground finely. but not to much - when it will be to fine, it will block brewing unit (you will see that the water will not come through. If you will do so, just turn the grinder one tooth back. 3. adjust time of grinding - you can choose from 5 to 10sec. Of course as much you will set, as strong the coffee will be. Here you will find the guide to set the grinding time up (page 9): www.repax.dk/files/EA8050%20temp%20mm.pdf Good luck \Mariusz
@mulpyk6 жыл бұрын
List Error Krups EA8080 Error 01 : Check operation of distributor switches Check distributor rotation (risk of drop in LV supply if distributor motor current too high). Check for wrong setting or position of motor in the distributor housing Add the spacer above the switches Error 02 : Concerns the ground coffee version Error 03 : - Fault in the actuator high position switch (mechanical or electrical) - Distributor switch fault - Faulty electronic boards connection - Actuator switch short-circuited Error 04 : Pump unprimed (start of self- priming cycle, fault 4 not displayed but recorded in memory of faults in line 6 of A-S mode) Distributor fault Error 05 : Flowmeter fault (wires reversed, connector offset, …) Switch or distributor switch control fault Drop of water on the flowmeter connector Pump fault Water flow blocked: hose caught, strainer missing (tank valve not actuated), tank badly connected Error 06 : Look for the leakage source: hoses, actuator, priming valve? Switch or distributor switch control fault: incorrect detection of cams error in distributor position in cylinder descent phase. Flowmeter hoses changed over Distributor problem (leakage at drain ..) Faulty connection between the 2 picto boards Error 07 : Ground coffee clogged up: Tamping head stuck Ejector blocked Tank badly connected Hoses caught (pump suction) Pump unpriming defect if filter installation procedure not respected Fault on the pump switch Switch or distributor switch control fault? (component or control via cake tray) Pump priming fault (in presence of filter? coffee-maker stored over a long period without tank or with tank empty?) Water-level board or bundle defective Flowmeter defecftive (indication of flow < reality, poor connection) Error 08 : Coffee grids plugged Creamy seal plugged Thermoblock plugged Switch or distributor switch control fault Tank removed during operation (pump unprimed). Error 09 : NTC fault (component, bonding, connector, wires…) Coffee leakage on NTC (resistor value) Error 0A : Thermoblock resistor fault (Faulty wiring connections) NTC unstuck NTC cracked
@octaviotabanez26533 жыл бұрын
Hi mariusz I have a krups xp 7200 and recently the red clean light start blinking and the machine doesn t work. Can you help me please? Thank you Octavio
@stacybertomen64436 жыл бұрын
Hi Mariusz, Thank you for your helpful videos. I am having a problem with the chute where the coffee comes out after grinding gets clogged. Also in your grinder cleanup video, what is the purpose of making a line on the plastic part of the grinder? Thank you for your time.
@MariuszGrden6 жыл бұрын
Hi, The line helps to assembly it back exactly in previous place. Instead of three grinding levels, you can adjust grinder base point on this step. \Mariusz
@stacybertomen64436 жыл бұрын
Thanks for the quick response. What about the chute getting clogged? The coffee grinds end up on top of the tamper and then it leaks water.
@saraymedina64096 жыл бұрын
Good afternoon my friend Please tell me What is de error code 14?! Best regards
@szkokastecz67335 жыл бұрын
Witam. Wiem, że od pojawienia się materiału minął długi okres czasu, ale być może będzie mi Pan w stanie pomóc. Czy ma Pan może wiedzę jakie wymiary ma ta sprężynka przy tłoku. Niestety zaginęła mi w trakcie demontażu i chciałbym dopasować w zamian inną, ale nie znaj jej rozmiarów. Z góry dziękuję za pomoc. Pozdrawiam.
@sniegslv8 жыл бұрын
Hi! Do you know how to adjust the grinder so it grinds more coffee? My coffee is always too weak - I have to use two-cup mode to make it a bit enjoyable. I would love to adjust the grinder so it grinds a bit longer (more coffee in the press). Thank you!
@MariuszGrden8 жыл бұрын
Hi, unfortunately I'm on vacation, so I can't check it, but I have explained it a few times before.So please dig into my comments - the answer is there
@benjaminbrekel72287 жыл бұрын
Mariusz Grden
@juanfernandolopez74574 жыл бұрын
Hola. ¿Te ocurrido que aparezca error 12.?
@jongsungyoon88532 жыл бұрын
thanks bro using T15? right?
@vessk0005 жыл бұрын
Can the grinder be modified to make a finer coffee by rotating one-step to the left before assembly?
@sarpijk5 жыл бұрын
Here try this kzbin.info/www/bejne/ioi3hIyce9Rqe9U
@brankodumanovski5 жыл бұрын
@vessk000 Did you try that solution?
@sarpijk5 жыл бұрын
@@brankodumanovski Hi, I did at first I caused the machine to block, grind was too fine as mentioned, but now I have nice froth and intense flavour.
@brankodumanovski5 жыл бұрын
You have moved plastic ring for how many clicks (steps)? @@sarpijk
@sarpijk5 жыл бұрын
@@brankodumanovski Not more than two. If it's too tight you will block it because it will be too fine.
@neilwarren7924 жыл бұрын
Be careful not to break the little wires on the coffee chute! Probably not a big deal but not that easy to see...for me at least
@yiselzapataa7 жыл бұрын
hi marius..thank you so much for your videos , i know that someone asked you about this before but i couldn't find the answer regarding this issue: my espresso is weak as a matter in fact it gets more foamy when i select coffee instead of strong espresso or espresso..what can i do? thank u again !!
@Poraqui3 жыл бұрын
You can set the grinder to grind finer by accessing it like in the video. Don't go more than 2-3 clicks bellow the finest factory setting. Assemble the machine again and pull 3 espressos on the new grind setting. This will recalibrate the grind time based on the new grind setting. On the 4th espresso you are ready to drink and test if the coffee is to your liking.
@dozer32816 жыл бұрын
Hi Mariusz, Thank you for your helpful videos. I dissasembled the grinder and found a plastic weel (looks like a child would paint the sun) which moves the coffee powder to the slide. the wings of the weel are very very short already. do you have any idea where to buy that weel ? I found in the internet only the metal parts of the grinder. thanks in advance
@MariuszGrden6 жыл бұрын
Hi, I was talking to somebody a time ago with the same problem - he has possibility to do new part by DIY from steel. On the after market there is a lot of spare parts so it shouldn't be a problem to buy used grinder. Even I have useless Krups XP7220 with burned electrical board that I am ready to get rid of. You can find some damaged machines that are sell for parts. Another idea is to ask on the place where do repair. I mean some servicing company (but not authorized) - they have for sure some second hand parts from damaged machines. \Mariusz
@brianstockford4 жыл бұрын
Did you ever find one?
@henrikzetterberg34184 жыл бұрын
@@brianstockford i second this. That part is broken on my machine, and i cant seem to find a replacement. Did you stumple upon something?
@brianstockford4 жыл бұрын
@@henrikzetterberg3418 I had one 3-d printed.
@henrikzetterberg34184 жыл бұрын
@@brianstockford sweet, thinking the same thing. Cheers!
@astras307 жыл бұрын
hi, great video, do you have any link of any company that are selling the grinders?
@MariuszGrden7 жыл бұрын
Hi, only second hand market - Ebay for example
@astras307 жыл бұрын
oh, no luck finding it on ebay :( i have an EA8050 but nothing
@korneliuszpawliczek58927 жыл бұрын
Hej Mariusz Podczas czyszczenia młynka, mimo iż robiłem to delikatnie, odpadły mi wszystkie plastikowe łopatki. Czy one są przymocowane do obudowy młynka, czy może kręca się? Czy młynek bedzie funkcjonował poprawnie bez nich? Pozdrawiam
@MariuszGrden7 жыл бұрын
Cześć szczerze to bardzo dziwne że odpadły - widocznie już wcześniej były wyłamane. Wydaje mi się, żenie nie są one do szczęścia potrzebne. Nie jestem pewny, ale zdaje się, ze te łopatki są częścią stałą dolnego korpusu młynka. Niestety w tej kwestji nie będę zbyt pomocny - nie spotkałem się nigdy z takim problemem. \Mariusz
@lubieautomatypl91357 жыл бұрын
Młynek nie ma szans funkcjonować poprawnie bez tych łopatek, służą one w końcu do wypychania zmielonej kawy z młynka do wsypu. Bez nich młynek zapcha się po krótkim czasie. Takie przypadki to norma jeżeli kawa zbyt drobno się mieli, lub np. jest aromatyzowana, a dodatkowy wpływ na to ma nieszczelność na elemencie tłoka (najczęściej wytarte uszczelki), a także niedrożny zawór 2 barowy w dystrybutorze, który nie zrzuca poprawnie ciśnienia po zaparzeniu kawy.
@korneliuszpawliczek58927 жыл бұрын
Dziękuję za odpowiedź:) Problem już rozwiązany. Łopatki dorobiłem z nierdzewki (tokarz i freze + trochę pilnika;)) same łopatki na necie za 100zł... Przy rozkręcaniu młynka należy uważać na lewy gwint! Oczywiście uszczelki też były wytarte i je wymieniłem:) Całość działa dobrze, a dziadkowie cieszą się pyszną kawą
@djiohio3 жыл бұрын
hello krups ea still writes me to clean the residue trap but i have cleaned
@Moro89038 ай бұрын
Co to ma być? Odetkanie młynka czy czyszczenie?
@stamentonchev8 жыл бұрын
My machine does some strange noise with the grinder and does not mill coffee whatsoever. Could it be a dirty grinder or is the grinder completely bust?
@MariuszGrden8 жыл бұрын
+stamentonchev Hi, For sure you have some problem with the grinder. There is no other way to check it than disassebmble it. This is really simple mechanism. For sure nothing serious happend. Good Luck
@kermitthefrog36855 жыл бұрын
Mine was doing the same. this method helped. there was a lot of fine particles and bean oil built up in the grinder and causing it to jam.cleaning made it grind properly again.. I realize this comment is 2 years old, but maybe it helps someone else.
@LaurM1233 жыл бұрын
@@kermitthefrog3685 bruh, u saved me with this comment 1 year later. Kudos
@zoltankovesdi47207 жыл бұрын
excellent video have error code 09any idea what it means and how can I fix it?thanks
@ryszardswiecicki1915 жыл бұрын
Ale po co czyścić młynek z kawy jeśli po pierwszym użyciu będzie identycznie?
@MariuszGrden5 жыл бұрын
Jeśli ustawisz młynek tak żeby mielił bardzo drobno, to może się zapchać. U mnie nie był na filmie zapchany, ale też mi się zdarzyło. Szczególnie kiedy kawa jest drobno mielona, a robisz sporo kaw pod rząd - wtedy wokół jest sporo pary i drobno mielona kawa klei się.
@costinescu998 жыл бұрын
The grinder on my machine stopped working completely. Shall i buy a new grinder or a cleanup would help?
@MariuszGrden8 жыл бұрын
+costin Hi, it is very hard to damage the grinder. It is often that the grinder is stoped by the coffee powder. Please clean it - it is costless but could help. \Mariusz
@astras307 жыл бұрын
i have similar fault, but the grinder plastic items that are inside are broken... any solution?
@brianstockford4 жыл бұрын
@@astras30 Any luck finding one?
@astras304 жыл бұрын
My friend made me identical one from steel and i replaced it...
@brianstockford4 жыл бұрын
@@astras30 hmm. ok, Looking all over the internet and I can only find one in Russia.
@hankvandenhoek68586 жыл бұрын
The same here as Dozer 5 days ago, also looking for a new plastic "wheel" that is underneath the grinder. Asked Krups but for vague reasons they will not cooperate. Please can some one tell where to get one
@MariuszGrden6 жыл бұрын
Hi, I was talking to somebody a time ago with the same problem - he has possibility to do new part by DIY from steel. On the after market there is a lot of spare parts so it shouldn't be a problem to buy used grinder. Even I have useless Krups XP7220 with burned electrical board that I am ready to get rid of. You can find some damaged machines that are sell for parts. Another idea is to ask on the place where do repair. I mean some servicing company (but not authorized) - they have for sure some second hand parts from damaged machines. \Mariusz
@hankvandenhoek68586 жыл бұрын
thanks Mariusz, I thought about that solution already but I rather have a new one. But I am afraid that's not going to happen
@brianstockford4 жыл бұрын
@@hankvandenhoek6858 Did you have any luck finding one?
@hankvandenhoek68584 жыл бұрын
Brian Stockford . Hi Brian, yes i did find one for €20,- ........in Moscow 😬. A colleague of mine who lives there bought it and sent it to me. Since then the machine was leaking while cleaning. I tried to fix that but after 2 or 3 times I was so fed up that i bought an other machine. A pitty, it was a fine machine as long as it worked
@louisdelamare843 жыл бұрын
Thanks ,i have repar m'y own machine with tout vidéo
@piotrkociub6705 жыл бұрын
Drogi Mariuszu, czy ta czarna kreska tonajlepsze ustawienie mlynka w KRUPS EA82 ? mój ekspres ma juz nastukane 6000 szt kaw,moje pytanie to: -- czy aby uzuskac dobra kawe z esencja i ladną pianką z góry filizanki to trzeba ustawic mlynek tak samo jak ty masz na filmiku ? -- moj model to KRUPS EA 8260 mhm. im z góry dziekuje ci za szybka odpowiedz.....
@MariuszGrden5 жыл бұрын
Czarna kreska to raczej punkt referencyjny przy składaniu młynka. Taki punkt odniesienia do zmiany ustawień względem tego punktu. Można ustawić drobniej lub grubiej mieloną kawę. Ale na jakość zaparzonej kawy mają wpływ trzy parametry, a grubość mielenia to tylko jedna z nich. 1. Aby kawa była mocniejsza, należy ustawić młynek na możliwie drobne mielenie - ale tu jest ryzyko, że zbyt drobno mielona kawa zapcha młynek. Jeśli się tak stanie, należy zmienić ustawienie o jeden ząbek tak aby była możliwie drobno mielona. 2. Drugi parametr to długość mielenia kawy a co za tym idzie ilość kawy jaka wpada do kotła - można to zmienić tak jak na tym filmie: kzbin.info/www/bejne/laKngXumj5eqnZo 3. Trzeci parametr to tłok - najczęściej to przez tłok kawa robi się lurowata i słaba. Każdorazowo przy wymianie uszczelek powinno się wymienić tłok. Kosztuje niewiele, a wewnątrz tloka znajduje się uszczelka "Cremy" - taka z mikroskopijnym otworkiem przez który przeciskana jest zaparzana kawa pod dużym ciśnieniem. Z czasem otwór powiększa się i kawa przelatuje przez niego bez oporu. Po wymianie tłoka kawa jest mocna, aromatyczna i ma charakterystyczną piankę. Ja polecam zrobić wszystko powyższe, a kawa będzie na prawdę smaczna. Pozdrawiam, \Mariusz
@piotrkociub6705 жыл бұрын
@@MariuszGrden dziękuję Ci za informację, wymieniłem uszczelki młynek też mogę sam ustawić ale nie dam rady wymienić tłoka, za dużo kabli pogubie sie, czy Ty wymieniasz tłoki odpłatnie, ile taki tłok kosztuje i ile robocizna ?
@piotrkociub6705 жыл бұрын
A czy wymiana samej uszczelki tłoka załatwi sprawę u mnie? Obecnie kawa jest zbyt mocna i zapycha się kociołek natomiast pianka crema jest znikoma
@MariuszGrden5 жыл бұрын
@@piotrkociub670 haha - właśnie że aby wymienić tłok, wystarczy odkręcić jedną śrubkę. Nie ma tam żadnych kabli. Kiedy zdejmiesz górną pokrywę ekspresu to tłok trzyma się na jednej śrubce. Uszczelki tłoka jeśli nie ciekną, nie trzeba wymieniać, ale wewnątrz tłoka jest uszczelka "Cremy" która nie jest dostępna osobno.
@piotrkociub6705 жыл бұрын
@@MariuszGrden aha A ha wymieniłem te dwa oringi na tłoku
@rzysk4 жыл бұрын
Moj ekspres mieli bardzo grubo kawe, przez co jest lurowata pomimo ustawienia na najdrobniejsze mielenie. Mam rozumiec, ze ten pierscien wlasnie ustawia poziom zmielenia i mozna "poprawic" fabryke. Czy jednak tego nie robic bo krups np. nie jest przewidziany do tak duzego zmielenia. Mialem inna marke i tam prawie krople bylo widac i kawa byla przepyszna i esencjonalna, a w krupsie leci jak z kranu. Nie wiem czy w fabryce sie pomylili przy skladaniu czy po prostu krups tak ma. Jest na gwarancji moze po prostu zglosic to zamiast grzebac, ale znajac zycie powiedza, ze cos wymyslam? Konkurencja miazdzy smakowo kawe z tego ekspresu, ale to za sprawa wlasnie tego zmielenia.
@MariuszGrden4 жыл бұрын
Można poprawić fabrykę i ustawić drobniej. Im drobniej tym będzie mocniejsza, ale można też ustawić zbyt drobno tak że woda nie będzie chciała przez nią lecieć. Ale jeśli ekspres leje wodą zamiast przeciskać wodę pod dużym ciśnieniem przez kawę, to raczej nie wina grubości mielenia, a wina uszczelki "cremy" - ale nie uszczelka kotła (po wpisaniu w google znajduje się uszczelka kotła), tylko chodzi o tą uszczelkę, która znajduje się wewnątrz tłoka. Ona ma taki mikroskopijny otworek przez który kawa przeciskana jest pod dużym ciśnieniem. Z czasem otworek powiększa się, a ekspres leje wodę zamiast parzyć kawę - kawa jest lurowata i nie dobra. Ta uszczelka jest dostępna wyłącznie z kompletnym tłokiem. Cały tłok nie jest drogi, a wymiana jest prosta i da się to zrobić bez rozbierania ekspresu (wystarczy odkręcić to miejsce gdzie się wrzuca tabletkę czyszczącą). Po wymianie tłoka kawa będzie mocna i z charakterystyczną pianką. \Mariusz
@rzysk4 жыл бұрын
@@MariuszGrden dzieki wielkie za podpowiedz. Udam sie do serwisu bo moze po prostu jest uszkodzony, a mam na gwarancji. No nic 14 dni bez kawy ;( jeszcze raz dzieki.
@jomecaar8 жыл бұрын
Good afternoon my friend Please tell me What is de error code 09?! Best regards
@MariuszGrden8 жыл бұрын
Hi, Error No9 means that the warmup time has been exceeded. This is one of the common issues, and is caused by unsoldered or unglued thermistor. You can find step by step repair explenation on my another video: KRUPS XP7200/EA8000 cz3. There from 6-th minute you will see what is the problem and how to fix it. I would like to send you a link to that video, but for Google sending links for own videos i SPAM spreading and they warn me that will lock my account out :) I hope You will fix the problem. Fingers crossed \Mariusz
@brianstockford4 жыл бұрын
Cleaned mine but noticed all the plastic tabs are broken....does anyone know where to get spare impeller
Hello, my machine is always performing the autotest, asking for water refill, could you help me? i would be very grateful, thank you very much
@MariuszGrden8 жыл бұрын
+Maria Teresa Seco Garcia Hi there, it looks like problem with the sink float or something with the float level sensor (inside the coffee machine - to see it, you have to disassembly the machine). If it is the float swimms well, you have to just disassembly the machine (this bigest black cover), and bend the sensor a bit closer to the float. Maybe the float is not totally sink yet, but is right on the edge. I will try to capture a short video with description how to dry the float. But in general - to dry the float, you have to put the entire tank into the microwave. Microwaves works only on water (only on wet things). So after one minute baking (not longer to do not heat to much to do not damage plastic tank. So put the tank into the microwave for a minute, take out and wait until it cools down and repeat it until the float will become totally dry (each time you can dry the float with thle napkin). I hope it is your only problem, because there is no error message that will mark something specific. Problem is not that obvious. The only path we can fallow is this message with the empty water tank. Fingers crossed \Mariusz
@Almnajed8 жыл бұрын
hi ... i have error coda 0A krups xp7220
@MariuszGrden8 жыл бұрын
+Aamer Almnajed Hi, Error 0A means: heating time exceeded Detailed problem: Heating is on, but the temperature wasn't changed Probable cause: - heating unit damaged - damaged heating unit wires - NTC sensor I know that it sounds bad, but for sure it is very simple - unglued or unsoldered thermistor (NTC sensor). Please have a look at explenation here: kzbin.info/www/bejne/pnnWnqeqf5xssNEm40s Fngers crossed \Mariusz
@andreiivan24925 жыл бұрын
Aparatul meu krups ea 8180 nu mai porneste stă aprinse becurile din dreapta
@ekspertklinikaagd48724 жыл бұрын
Bardzo profesjonalnie wykonana naprawa gdyby kogoś interesowały części do tego modelu zapraszamy do sklepu www.klinikaagd.pl www.klinikaagd.pl/czesci-agd,czesci-do-ekspresow-do-kawy,krups,ea8000,EA8000E1700/
@andrzejkrol72655 жыл бұрын
skad mam wiedzie w jakim kierunku przesunac pokretlo? w lewo czy w prawo? ma to znaczenie?pozdrawiam
@MariuszGrden5 жыл бұрын
kręcąc da się zaobserwować że górne żarno młynka przesuwa się w górę (grubo mielone) lub opuszcza (drobno mielone).
@andrzejkrol72655 жыл бұрын
@@MariuszGrden dziękuję.
@andrzejkrol72655 жыл бұрын
@@MariuszGrden witam, to jeszcze raz ja. dzisiaj skrecilem swój ekspre Krups - wczesniej wymieniajac uszczelki - jednak nie wszystkie, zabraklo mi na ten moment chyba odwagi. wymienilem uszczelki zaworu 2-barowego, tloczka oraz ta mala w piecyku. wczesniej mi mocno cieklo pod ekspresem i ciagle sie zapychal przy odrzucaniu sprasowanej kawy do pojemnika. wracajac do tematu - skrecilem moj ekspres i po wlaczeniu naprawde duza roznica - pieknie mieli mynek, kawa goraca, intensywna ale troche cieknie.... woda zaczyna lekko sie wylewac w momencie gdy kawa jest juz zrobiona i w fazie koncowej gdy sprasowany kawalek jest odrzucany do pojemnika nie jestem przekonany, ale chyba z wezyka ktory jest podlaczony do zaworu 2 barowego, ktory oddaje koncowke cieczy do pojemnika ze zlewka:) byc moze zle go umocowalem i sie wylewa poza pojemmnik...? ma Pan jakas teze na ten temat? pozdrawiam serdecznie.
@MariuszGrden5 жыл бұрын
@@andrzejkrol7265 Szczerze to już chyba ciężko mi będzie pomóc - zmieniłem ekspres na inny i nie mogę sprawdzić jak to w tym Krupsie jest. To co mogłem to udokumentowałem. Pozdrawiam, \Mariusz
@thierryrompion85422 жыл бұрын
Juste où un
@icinemagr46213 жыл бұрын
Worst Coffee maker ever. I had the quetro 450 euros and i send it back. after 30 coffees had problems with strange messages I bought a la pavini and now i am happy. Thsi crap is full of plastic.,