KTM LC4 640 chain and sprockets replacement

[@markmckell8817]

Good vid. Thanks for making. Couple of observations - Rear sprocket - torque wrench goes on the nuts - not the bolts. And chain too tight.

[@codenamenoob4973]

Always stick abit of grease on the countershaft spines before putting the sprocket on, keeps them intact for much longer 😉

[@Roadified]

Can front sprocket be replaced without spiting the chain and just loosening chain tension on the back wheel?

[@olajfa11]

yes, possible

[@Roadified]

Thanks, I will change mine today. Will go from 42 x 16 to 42 x 17

[@emreakpinar8730]

@@Roadified arazide bu ölçüler sıkıntı yaşattımı

[@c.j.o8]

I have a 2001 KTM 640 E. Quick question: What is the name of the plastic piece or guard that lays on top of the swing arm preventing the chain from rubbing. It is the piece closest to the front sprocket.Maybe called the chain sliding guide? After a long time, mine finally wore and fell off. Thank you, ahead of time.

[@olajfa11]

Its name is chain sliding guard. Original part number: 58307073000. Chechk in google :)

[@emreakpinar8730]

Disli ve zincirin adresini gönderirmisin bende almak istiyorum .birde uzun vites aralığı olması için dişli seçimi kaç olmalı teşekkürler

[@olajfa11]

www.supersprox.com/

[@nyndmrts]

Ön dişli orijinalinden 1 dış fazla alın toplamda 1 vites kadar farkeder.

[@R3D.X]

Hey Buddy ! your videos are really awesome . how do you reach the slave cylinder on those bikes ? i guess i have to remove the front sprocket, right ? but it seems the small oil filter lines are in the way , do i have to lose oil as well ? my clutch isnt keeping the oil i put in it , i am guessing the slave cylinder is leaking , what do you think ?

[@AMBULL4X4]

Great vídeos! What brand and reference are the chain, front sprocket and rear sprocket that you are installing?

[@nyndmrts]

A late reply but, i know only that the rear sprocket is Supersprox stealth...i use the same.

[@eyeflynoosa]

@@nyndmrts you wouldnt happen to know the correct torque for the nut holding front sprocket in place? i have a 07 625sxc lc4 assume its probably the same as this bike.

[@nyndmrts]

@@eyeflynoosa 90 nm for the back 100 nm for front. This is for my 990 adv. If you write me your e mail, i can send you repair manual s and owners manual both for lc4 and lc8 bike.

[@eyeflynoosa]

@@nyndmrts left a couple of replies for you, they get deleted. cant leave a email address I guess. we`ll see if you get this reply. but, i found the torques specs for the 625 sxc sprocket nut on a forum, 60nm. which makes sense to be somewhat less than the bigger bikes

[@eyeflynoosa]

@@nyndmrts if you get this , you could send the manuals to iflyfpvaustralia atthe normalgmailaddress`

[@zsoltlazar4770]

Jó videó! Köszi a feltöltést! Épp egy lc4 640 supermoto vásárlásán gondolkozok! Esetleg írnál pár sort ide, hgoy mik a te tapasztalataid a géppel?! Megéri egy jó állapotút venni, nem költöm rá a nadrágomat? Tölthetnél fel több lc4 karbantársról szóló videót! ;) Köszi előre is a választ! Gumi fákat!

[@olajfa11]

Nem volt vele gondom. Önindító reléjénél szakad el egy kábel, más hibája nem volt. Érdemes utolsó szériást venni és rendszeresen áthúzgálni a csavarokat az egész motoron a rázkódás miatt.

[@zsoltlazar4770]

👍 oké, köszi!

[@adrian3385]

Kette viel zu stramm. Da ist ein lagerschaden vorprogrammiert....

[@linusbylund9461]

Clip in wrong direction =)

[@nyndmrts]

He did correct

[@linusbylund9461]

@@nyndmrts Yes he did, donno who i wrote that 1 year ago

[@vitvit4183]

колхоз!