KUKIRIN G3PRO - Introduction P Settings - Speedhack- Zero Start - Cruise Control

[@Natsukashii1111]

thanks a lot for this video, my G3pro came by default with PA at 5 and I didn't know that so it was way too powerfull. Tonning it down helped me appreciate it a lot more!

[@SYTROP14N]

That's correct my is also preset to 5, way too powerful for two motors, each start its almost spin the wheels, now set to 1 and is where it supposed to be.

[@JohnOLooney]

@@SYTROP14N same here , mine was set at 5 , its way to harsh, i set mine to 1

[@itaco8066]

Great video Thank you!

[@BössTöyö888]

Is that PA is the acceleration? What is the highest accel. 5

[@otakarlibal]

Thanks for the video! Is there any way to keep the full power and full speed, but just improve the throttle response. It is way too sensitive. It feels like you go from 0 to 15% throttle and nothing happens, then you go from 15 to 16% it jerks forward and gives you like 70% and then the remaining 17 to 100% throttle just moves you from like 70% engine power to a 100%. If there is any way to make it linear and easier to control i would really appreciate

[@JohnOLooney]

the throttle is adjustable in the parameter settings , its set at 5 by default, toggle it down to 1 is my advice - its jsut too spicey bny default and youll pull your arms off

[@Prodigee1979]

Why you want to leave Pb off (0) ? It's the E-brake strength and it's very important to have it ON if you want to brake/stop fast. If it's on 0 you will only use the normal brakes (front and back) and will have to buy new brakes too often, the e-brake is really important!

[@clementevillalobos345]

The ebrake on this is way too powerful and unsafe. I barely squeeze the brake lever and it locks the brakes almost throwing me off. I have it set at 1 the minimum too. I don't like. Its very dangerous when front brake engage. The stopping is way too abrupt for normal riding around 15 mph. It's unfortunate it can't be set to activate at higher speeds. I might disconnect the electronic if I continue to experience this problem. I just feel safer in braking. The hydraulic alone suits me just fine. Light riders be aware of this problem.

[@ladehier]

if the battery is full and your first drive are down hill mean you drive from a mountain down then possible also your battery get damaged. some battery have this problem. also you are right with other arguments.

[@kendallleary9991]

Once driving how do you activate cruise control

[@ricobico1872]

It does it automatically....do not recommend....

[@faridskafee5392]

I just want this monster to run without pushing. Help me with that through the settings

[@abbiesekoum2249]

What is the PA about ?

[@JohnOLooney]

acceleration

[@James-b5u1w]

Bu doings po 7 dose all the gears go to Max speed? Or only gear 3?

[@ggale1]

PB Not work. Why?

[@linqu69]

I’d like to know that too, on the manual it says it would work, that would be important to work, without it brake pads wear out quickly.

[@robertcseh4619]

My Pb brake is also not working

[@robertcseh4619]

Who know what will be the problem please.

[@Prodigee1979]

Why you want to leave Pb off (0) ? It's the E-brake strength and it's very important to have it ON if you want to brake/stop fast. If it's on 0 you will only use the normal brakes (front and back) and will have to buy new brakes too often, the e-brake is really important!

[@Prodigee1979]

Set it to 5 or 4 then you feel it.

[@BössTöyö888]

Psettings For kugokirin g4pro plsss

[@ua2924]

Hello! Please tell me, is there a recovery on Kugoo Kirin G3 Pro?

[@octavioborda3767]

p07 work for only 1 of the 2 motors . so impossible de control speed on second motor …. useless

[@ladehier]

Yes you are right. But the price is really ok.

[@iphone-repair-fuengirola]

Good video

[@Nutrient16]

This doesn't work for M5 pro

[@ladehier]

Ok let me try out byself. Our tean was sick last 2 weeks. Let me come back to you with good news ;)

[@maximljubavin9156]

Thank you we are waiting

[@JohnOLooney]

this is for the G3 pro, why would it work on a M5 Pro ?

[@alexanderthegreatest5336]

My G3 has a speed issue, it doesn't go faster than 15mph though i switch to mode 2 or 3, still same speed. Who can help me out?

[@ricobico1872]

Go to setting PO7....Set it to 100....Long press

[@deijannoreiga3924]

@@ricobico1872mine is set to 100 and is still doing that

[@SYTROP14N]

P7 is useless. I've set 33 as P7 value, and 2nd gear two engines still goes to 45km/h but 3rd gear is limited to around 35km/h. xD

[@savas0012]

This doesn’t work for m5 pro

[@ladehier]

its an G3 Pro. not all scooter have same functions and also not same way how to come inside the hidden settings

[@alexandresquare]

same, but you still have part of the settings like cruise controll