HP CQ42 DEAD HOW TO READ SCHEMATIC DIAGRAM | ENGLISH | VIN Section OF 3V 5V Jugaad |Chiplevel Repair

[@manojsahu6840]

Very knowledgeable cashstudy sir . Jab ve aap naya video dal te he us me na kuch na kuch naya chik ne ko mil ta he. Thank you for sharing this amazing information.

[@laptex1377]

Really appreciate your true feedback. Aise support krte rhe r video share krte rhe.

[@trisztan_]

Laptex is the best🙂🙂🙂

[@laptex1377]

Thanks bro. Keep supporting and sharing our videos.

[@YogeshKumar-vh9zn]

Excellent job sir 🙏🙏

[@laptex1377]

Thanks bro. Keep supporting and sharing our videos.

[@herbethjumanne2983]

Real its exceptional knowledge. Clear explaination , nice work Sir

[@laptex1377]

Thanks bro. Appreciate your support. Keep sharing the videos.

[@dollarbillbolaji7855]

Great job sir, I really enjoy the video keep it up sir

[@laptex1377]

Thanks bro. Keep sharing our videos.

[@laptechworld7155]

Rocking sir as always.

[@laptex1377]

Thanks bro. Keep supporting and sharing our videos.

[@mr.hahmed138]

VERY GOOD AND LOT THANKS MR NASER

[@laptex1377]

Always welcome dear. Keep supporting and sharing our videos.

[@crazykhushal1.717]

Deep knowledge 👍

[@laptex1377]

Thanks. Keep supporting and sharing our videos.

[@PcRefixSystem]

Best knowledgable video

[@laptex1377]

Thanks bro. Keep supporting and sharing our videos.

[@mugabirapaul8653]

That's great sir because that case for crystal input side oscillates once has been a challenge to me. and I had thought that it's normal for one side of crystal to oscillate. But now I have understood that logic that I should use ground which comes with probe. I really appreciate your help

[@laptex1377]

Seeing comment like this we get motivated to excel our knowledge and works. Thanks to encouraging out true efforts.

[@manishchauhan1447]

Very good video sir ji

[@laptex1377]

Thanks bro. Keep supporting and sharing our videos.

[@biegame9santiago919]

Hi thank for sharing a wonderful and helpful video to us. Sir can u give me a advise what is the problem if i can get only 3volts from second mosfet before the current sensing resistor

[@laptex1377]

Thee is leakage in the MOSFET or MOSFET channel is not open completely...that is the MOSFET is not working fine. Or sometime leakage from the auxiliary component of the circuit.

[@Godunjoify]

I like this video.

[@laptex1377]

Thanks bro. Keep supporting and sharing our videos.

[@naf4494]

Nice conceptual, Sir if flash (8mb) was written successfully but not verified after written (using ch341a device and programmer) and board does not trigger, so is the flash corrupt or something else? (acer aspire one]

[@laptex1377]

Both possible.

[@devichetan]

Sir did you need to reprogramme the I/o , or we can directly install new chip?

[@laptex1377]

If SIO is programmable then it needs to be reprogrammed.

[@prashanshan7125]

Keep it up..!

[@laptex1377]

Thanks bro. Keep sharing

[@mugabirapaul8653]

Please sir slightly, I would like to inquire from you I want to buy my first sio programmer but sir from your experience which one do you recommend for me ENIT OR SVOD WHICH CAN PROGRAM ALL LATEST NEW SIO CHIPS

[@laptex1377]

SVOD

[@mugabirapaul8653]

@@anshadedavana OK that's great idea, please thanks alot

[@mrmilan2012]

Sir microscope ki light thoda increase hona chahiye...board thoda dark nazar aata h... Don't mind plz

[@laptex1377]

Okay bro. We will try to improve. Thanks for your feedback.