Laser Duct Fan Upgrade | AC Infinity A6

  Рет қаралды 4,464

3DHP

3DHP

Күн бұрын

Пікірлер: 18
@mikedoyle5362
@mikedoyle5362 10 ай бұрын
Great start! Always good to have a laugh!
@pcvanvliet
@pcvanvliet 10 ай бұрын
Looking good Jerry, good airquality is important in your makerspace when you spend a lot of time there.
@mikedoyle5362
@mikedoyle5362 10 ай бұрын
Really like the ac infinity. I use the 6in hose up until the last 5 in and have a reducer for 6 to 4.
@LSEngraving
@LSEngraving 10 ай бұрын
Looking good Jerry as always I love that unboxing knife
@KRich408
@KRich408 10 ай бұрын
I might upgrade the Hon&Guan 130 CFM it's Junk for my Roly 20w , I just etched a bunch of mirrors today. my basement smells like a plastic factory.
@3DHP
@3DHP 10 ай бұрын
Well that's no good.You don't want to be breathing in anything that might have harmful chemicals in it.
@mgl_angel0542
@mgl_angel0542 4 ай бұрын
Great System set up! 🫡
@chrislmink
@chrislmink 10 ай бұрын
Make sure you keep that back door locked if you have a waste gate open it sticks out past the door when open lol. I didnt think it was that loud at all.
@3DHP
@3DHP 10 ай бұрын
It easily turns at the Y. Thought about when I screwed to the wall.Louder than the smaller one,but ok.
@mikedoyle5362
@mikedoyle5362 10 ай бұрын
Do you use a window to vent
@3DHP
@3DHP 10 ай бұрын
lol,,you didn't watch the video.
@BLUEMOONENTERPRISES
@BLUEMOONENTERPRISES 10 ай бұрын
When you removed the fan, were you able to continue to use the same exit fitting minus the fan to attach the hose? Was it difficult to remove the fan? My Lasermatic should arrive soon and I'm trying to sort out an exhaust for it, which is going to be very similar to yours. Thanks.
@3DHP
@3DHP 10 ай бұрын
I just used shorter bolts and put the duct back on. Once you unplug fan,wire with connector will slide out of the aluminum channel,no reason to try and pry it off.Its very easy to do.I also left the fan screen on the inside.
@BLUEMOONENTERPRISES
@BLUEMOONENTERPRISES 10 ай бұрын
@@3DHP Thanks! Great explanation!
@TheLouisianaHobbyGuy
@TheLouisianaHobbyGuy 10 ай бұрын
I had one of these, and it seemed the only settings that worked were the last two. Should just be High/Low.
@KRich408
@KRich408 10 ай бұрын
I just purchased this fan its great! 👍 im still trying to figure out how to remove the factory fan without cutting the wires or damage the condit or orange plastic? The fans cord won't fit through the Condit Roly used.
@3DHP
@3DHP 10 ай бұрын
Unclip the fan,the wire is like 6 inches long.Do not remove the silver metal duct.The wire and connector will slide through it.Then use shorter bolts for duct with grate. Save fan and screws,if you ever sell it,you can put back to stock.
@KRich408
@KRich408 10 ай бұрын
@@3DHP ok thanks 👍👍👍👍👍
AC infinity Cloudline T6 vs Spider Farmer® 6 Inch Inline Fan
7:17
Jaidarman TOP / Жоғары лига-2023 / Жекпе-жек 1-ТУР / 1-топ
1:30:54
Office Build Begins: Solving 2nd Floor Heat w/ AC Infinity T12 fan!
22:31
Why you should get a FIBER LASER
26:49
Matt Estlea 2
Рет қаралды 5 М.
Laser Ventilation with Acrylic Window & Infinity S6 Duct Fan
7:00
NovoWorks Color Imaging
Рет қаралды 1,6 М.
Is this the Quietest Fan? | AC Infinity Cloudline Series
7:28
Inline exhaust for better laser smoke extraction
20:06
Vintauri
Рет қаралды 7 М.
COMPARISON & TESTING  THE BEST  6 INCH INLINE FAN FOR INDOOR GROWS
11:23
Shop Talk -  Fume Evacuation From Lasers and 3D Printers!
7:43
DIY3DTECH.com
Рет қаралды 67 М.
AC Infinity Cloudline S4 | The Inline Fan for your Grow
5:52
Happy Hydro
Рет қаралды 44 М.
Choosing a fan for the Glowforge
6:09
Martinson Manufacturing
Рет қаралды 117 М.
How to Make a Real Diamond - (Not Clickbait)
8:51
JerryRigEverything
Рет қаралды 3,6 МЛН