Lazy saturday afternoon | DE Noveske MWS with HPA Adapter

Some more Nyvång airsoft pew with the double eagle noveske combined with a T8 HPA adapter. Pretty slow afternoon and a lot of the players leaving early.

[@OperatorJackYT]

*GBBR is Meta* You cannot change my mind

[@Basterds_Airsoft]

😄

[@sagaliv8864]

Kul med gbbr och bra videos med schysst bakgrunds musik. Skulle vara intressant att se lite mer av vapnen och kanske någon video med vilka gear som du/ni kör och gillar. Keep up the good work.👍

[@Basterds_Airsoft]

Tack!

[@centurygaming3374]

Hey awesome gameplay got one myself used it in a fair few games and it's awesome just curious what hpa adapter are you using with it? Keep up the awesome content

[@Basterds_Airsoft]

Cheers! It’s the T8 one

[@oxApplePkerxo]

Where did you buy the adapter? Have you had to do something to get it to work properly?

[@Basterds_Airsoft]

It was temp in stock at Weapon762. I had to modify the BB channel and "feed entry" into the adapter. I superglued some plastic strips on each side of the channel to make it more narrow as the stock width was too wide and would jam frequently.

[@PROPHET-47]

Did you shim Adapter? I have the same Set, and IT shoot properly, only when i hold the Mag, so I shimmed Adapter for Little bit higher position

[@Basterds_Airsoft]

I have replaced the gas router / gasket with a guarder airtight + some shimming yes.

[@davidsarafi9624]

@@Basterds_Airsoft what kind of adapter are you using?

[@Basterds_Airsoft]

@@davidsarafi9624 T8

[@jakubziak3404]

Hi, great videos. Your gameplays and the fact you seem satisfied with DE MWS were one of the main reasons for me to buy it too. I played 2 games with it and it was awesome. Since when in stock, it shoots too hot for my field, i changed nozzle for RATECH but it broke after 2 games, and during install I had to file down some material for it to fit. Do you know good nozzle or nozzle/ bolt combo that will fit and work without modding? Or can you tell me what you upgraded in yours?

[@Basterds_Airsoft]

I can highly recommend the Federal Concepts NPAS. It takes the good bits of the angry gun MPAS nozzle and the Ra tech valve and comes at a good price. (google federal concepts) Did your nozzle break from a missfeed or did the ra-tech break? If you got a missfeed nozzle break (where the nozzle slams into the hop house). You might need to shim the bottom rear of your magwell with some velcro or something to avoid the feedlip to drop low during firing. Especially if you are using TM or G&P mags. If you need a new complete nozzle a stock TM nozzle would be ideal but are hard to find. I have heard good things about the guns modify and the unicorn nozzles. Avoid BJ Tac nozzle. I had one and it snapped. Seems to be bad quality plastic. The angry gun complete nozzle is ok aswell. Hope you figure it out and thanks for watching!

[@jakubziak3404]

@@Basterds_Airsoft I am using Guns modify magazines. The RATECH nozzle is the one that broke. The lower half of the part that is pushing gas to chamber broke inwards, but I don´t know the cause. I will buy the new nozzle and NPAS or entire new BCG. Where I live is a little tricky to get certain brands of stuff. Most of the shops here have Angry gun nozzles and Angry gun aluminum BCG and one site has the G&P aluminum BCG (G&P is without NPAS). Are these OK in your opinion? Because I was dissapointed with RATECH because it had bigger diameter than stock one and I had to file it down to fit it in bolt. BTW I looked at the Federal Concepts NPAS and it looks nice. I will try it when I get my hands on compatible nozzle

[@Basterds_Airsoft]

The angry gun nozzle is ok. I have 2. I also have 2 angry gun high speed aluminium bolts and the DE noveske hates them for some reason. Very easy to get missfeeds. They are also quite fragile and show alot of wear now. So IMO. Avoid the lightweight bolt. Buy the angry gun nozzle if its easy to come by. (or get the federal valve)@@jakubziak3404

[@jakubziak3404]

@@Basterds_Airsoft I was looking at non hi speed angry gun BCG and they are the same price as the gun itself. So I will buy angry gun nozzle and try to put in in stock bolt and hope it will fit.

[@Basterds_Airsoft]

worst case you might have to sand the nozzle body abit if its too tight. I had to do it on the BJ tac nozzle in the DE bolt. Never tried AG nozzle in DE bolt but I dont see why it wouldnt work. I currently have the stock nozzle with a Federal Concepts valve installed and it works great.

[@maglicairsoft4183]

What pistol are you using

[@Basterds_Airsoft]

Tokyo marui M&P9