Le Nouvel Antminer S19 Hydro : Performances Ultimes et Refroidissement à l'Eau

[@kadizmad5081]

Merci pour l'explication

[@angeloanjos2477]

Hi, awesome video! The 1st good one on the S19 Hydro! Well done! I have a question about S19 Hydro, i know it has a Low Power mode with the latest firmware, can u tell me what Hashrate and power consumption we get on that mode?

[@miningdelta]

hello we haven't tried the low power mode yet we are rather overclocking to have more hashrate

[@dhanbadkikudi]

@@miningdelta can you please make video how to overclock s19 hydro and how much overclocking is safe for s19 hydro without changing psu

[@asmr-xuanzi]

please tell me if the radiator is placed outdoors, the liquid temperature will be lower than 20℃ for low temperature protection. Is there any way to heat the liquid in winter?

[@miningdelta]

you can put antifreeze for the winter

[@phillipjung4889]

Good video. My miner has red blinking on the first right signal where the short 4 hoses in & out. And machine is not mining properly. Do you know why it happens? 😅

[@miningdelta]

hello we tell me that one of the hashrate cards is flashing red, what does the asic interface say is which channel is the hashrate card or not?

[@kitewinds663]

Why mix air into the cooling liquid? If you feed your reservoir from the bottom upwards by an extension pipe on the inside two thirds up in the reservoir, and the the liquid out in the bottom too, then the air stays out (bubbles do not reach the bottom outlet). Just rebuild the reservoir to a better set up. Also, wouldn't it be nice if you could cool from two points in the miner? So that heat from one PCB didn't feed over heat to the next PCB board? For that they need to use two separate radiators. But the temperature of the miner chips would be more even? In this S19 it would mean that you took out a stream after the PSU in addition to the current outlet. No one?

[@miningdelta]

the radiator works this way, it starts in the tank --> goes into the asic power supply --> goes through the three hashrate cards --> comes out of the asic --> enters the radiator ( to cool the liquid) --> exits into the tank (upper part)

[@AR-ol4yf]

Dear which liquid do you use? Only water would be not enough?

[@miningdelta]

you have three possibilities: demineralized water, watercooling liquid (for custom computers) or ethylene glycol.

[@lucamazzo3626]

Great video! Where did you get the hose that connects to the ASIC?

[@miningdelta]

we supply the pipes with LIANLI 12KW radiator

[@alecsandrolima]

hello. Very good video. What system do you use to manage this Asic Hydro? I'm thinking about using Hiveos, but I'm getting Hiveos firmware installation and there's some problem.

[@miningdelta]

I use the classic Bitmain interface

[@alecsandrolima]

thanks@@miningdelta

[@YannDadia]

Très bonne vidéo! Est ce qu'on peut mettre du liquide diélectrique aussi?

[@miningdelta]

Oui bien sûr qu'on peut mettre du liquide diélectrique, c'est juste un peu plus cher comme liquide pour faire du watercooling, vos mieux le mettre dans l'immersion cooling.

[@coinboxmining]

ERROR_TEMP_TOO_LOW: Water temperature is too low! stop_mining_waiting: Water temperature is too low! any idea?

[@MartinErrandonea]

Très bonne explication ! Combien d'appareils (S19 Hydro 198th) peuvent être connectés à un radiateur ? Quelle est la vitesse de pompage (litres/m) ? Merci!

[@miningdelta]

Un seul S19 hydro peux être connecté au radiateur, si vous souhaitez brancher plus de S19 hydro il faudra le mettre dans l'armoire watercooling: miningdelta.com/fr/immersion-cooling/142-armoire-lianli-watercooling-120kw.html

[@jean-makensondsance4363]

Je peut commandé sur quel site ?

[@miningdelta]

Bonjour notre site web est miningdelta.com

[@lebeg59]

savez vous la consommation du radiateur svp ?

[@miningdelta]

Bonjour la consommation électrique du radiateur LIANLI 12Kw est de 60w, il fait tourner une pompe et 12 ventilateur 120mm.

[@sahilthakur5444]

ENGLISH VERSION PLEASE!?!?

[@dArmenn]

Im a seller also, this days ill do in spanish in my chanell. if you interested let me know, thank you

[@s.a296]

Are you cooling it with tap water?

[@miningdelta]

No, not tap water, you have three possibilities: demineralized water computer water cooling liquid ethylene glycol

[@rappelz7109]

Jai une problem de temperareur psq jais uliliser 2 antminer en 1 radiateur est que il ya un solution?

[@miningdelta]

Il faut mettre 1 radiateur par antminer (il chauffe énormément) ou alors acheter l'armoire pour avoir 4 unités antminer.

[@akshaychandela7769]

Сэр, какой из 4-х портов на порту питания машины является заземляющим/нейтральным?

[@miningdelta]

Здравствуйте, загрузите наши инструкции по установке (на французском языке), и вы увидите, как подключить Asics к трехфазному сети. Ссылка здесь: miningdelta.com/fr/index.php?controller=attachment&id_attachment=24

[@akshaychandela7769]

Sir which is the earth /neutrat port from the 4 port on the machine

[@miningdelta]

hello download our user manual for the Antminer S19 hydro to know how to connect it in three-phase. here is the link: miningdelta.com/fr/index.php?controller=attachment&id_attachment=24

[@alexivancamachomorales2039]

Bonjour, quel câble utilisez-vous pour connecter l'asic au courant?

[@miningdelta]

Bonjour un câble propriétaire a Bitmain en triphasé

[@khalilbelkaid394]

Est ce qu'il y a une solution pour diminuer le bruit des ventilateurs ?

[@miningdelta]

Oui avoir une pièce climatisée il feront moins de bruits

[@JafCo-r6d]

bonjour je voudrais connecter mon asic sur du monophasé, existe t il des adaptateur triphasé vers monophasé et est ce que cela convient pour la machine ?

[@miningdelta]

Bonjour il existe des transformateurs de 380v en 220v pour des machines semi- industrielles, je ne sais pas s'il pourrait marcher sur un Asic.

[@mrlowplayer4106]

What is the name ob this power cable typ?

[@miningdelta]

it does not have specific names "the antminer hydro cable" it is only manufactured by Bitmain.

[@MariaClara-zq8on]

Bonsoir mon ami, quel type de connecteur as-tu utilisé à l'entrée et à la sortie du système de refroidissement de la compagnie minière ?

[@MariaClara-zq8on]

so sorry about my bad frech , i wanna know what types os connector you use in imput and output watter in s19? thanks.... if you can send a link of this connector , i will so glad.

[@miningdelta]

hello we have created a connector in 3D printing to connect to the S19 Hydro

[@MariaClara-zq8on]

@@miningdelta did you have a model? or image?

[@miningdelta]

here is the link to download the STL of the connector www.thingiverse.com/thing:6153921

[@MariaClara-zq8on]

Thank … I Will make some 10 kkkkk

[@lebeg59]

savez vous quelle est le meilleur liquide à mettre dedans ?

[@miningdelta]

De l'éthylène glycol

[@lebeg59]

@@miningdelta et est il disponible a la vente au particulier ? et avez vous un endroit ou le trouvé svp ?

[@lebeg59]

@@miningdelta il ce met pure ? ou juste que c'est le même liquide que l'on met dans les radiateur de voiture ?

[@miningdelta]

Nous ne vendons pas de l'éthylène glycol, chercher sur internet

[@miningdelta]

Il existe de l'éthylène glycol pure ou coupé directement, le pure il faux le dilué a 60/40% avec de l'eau déminéralisée. Ce n'est pas du liquide de refroidissement d'une voiture, mais ça doit aussi marcher comme l'eau déminéralisée, le liquide de watercooling.

[@brunosfreis]

I drew your attention to the connection error, are you misleading all users into burning their machines and deleting my post? I think it was the right attitude....

[@miningdelta]

what a connection error!!

[@brunosfreis]

The instructions on bitmain are very clear, the cooled water first enters through the ashboard area and then comes out hot in the PSU area, in your video it's the opposite, you put the cold water through the PSU first, this will cause greater heating in the end of the ashboard circuit. I found your video to be one of the best on the internet, but this error could cost some less attentive users dearly. especially those who don't look at the official instructions.@@miningdelta

[@guillaumew627]

bien mais ton circuit est plein d'air et ça ce n'est pas terrible pour le refroidissement

[@miningdelta]

C'était juste pour la présentation il faut juste bouger l'asic et remplir complètement le réservoir.