Learn Electronics | LED chaser with 555 & 4017

Рет қаралды 15,756

Күн бұрын

A video tutorial showing you how-to construct a simple LED chaser circuit on a breadboard using a 555 in astable mode and a 4017B as a decade counter.
Please check back regularly for more content and updates. If there is a specific topic you would like me to cover in future videos, please let me know in the comments. Thanks for watching, and please don't forget to click like and subscribe!
/ electrobench
#LED #Chaser #555 #4017B #Breadboard #Project #How-To #Electronics #Learn #IC #Integrated #Circuit #Tutorial #Learning Electronics #Learn Electronics #Basic Electronics #Astable Mode #LED #LED Chaser #4017 #4017B #Running LED #Moving Dot #Decade Counter

Пікірлер: 20

@MrPhatNOB 3 жыл бұрын

As this channel's number 1 fan, I am very happy to see a new upload! Glad you're still kicking! If you start a Patreon I would gladly sign up!

@Richie_ 3 жыл бұрын

I've only been learning this stuff for 4 weeks and every video I watch adds another item to my shopping list. I like the way this video is done.

@rromano158 Жыл бұрын

Do you have a downloadable schematic diagram for this circuit? AAAAAGH, I really needed this LED circuit to work!! Following your instructions on the video, I put everything on the breadboard. The ONLY way I could get the group of 10 LEDs to cycle is to MANUALLY twist the variable potentiometer back and forth. The only thing the LED attached to the 555 timer would do is brighten or dim but never flash. I've tried around 6 different 555 timers, but still cannot get the LEDs to cycle on their own. If I remove the LED attached to the 555 timer I cannot get the other 10 LEDs to do anything. What am I doing wrong?

@joshuahawking6577 9 ай бұрын

Use a smaller capacitor for the 555 to flash to improve its frequency I used 2.2uf

@primalvengence8443 16 күн бұрын

i know this is a old thread but do u remember what value trimpot u used?

@tommstanley6021 Жыл бұрын

I am using a potentiometer to control and slow down the speed of the 555 and the LM4017 outputs. I'm wanting the LED's to fade when they come on and off and I am experienced with many different circuits that fade LED's. I have tried basic cap and resistor pairings at the LED's and also by using the 4017 outputs to drive bc547's transistors that turn on the LED's, again with different arrangements of caps and resistors on the base and/or emitter sides and I've also tried resistor/cap arrangements that can turn square waves triangle or sine, with and without the transistors. In all cases, I can get a very controllable fade out of the LED's but cannot get them to fade on. Is there something about the output of an LM4017 that will not allow it's waveform to change or for a capacitor to slowly charge? Or something else that I just can't figure out?

@stephenwarren6539 Ай бұрын

what values are the components on the 555 please ?

@justinindustries 9 ай бұрын

Nicely explained!👍

@itsmegrace1028 9 ай бұрын

Greatt info. I'm building a diy synth with 4046,4093,40106,4017,4060 etc cmos chips. just worried about connecting my LEDs to the chips and harming the cmos. My 5mm green, yellow, blue, white are 3-3.2V and the orange and red ones are 2-2.2V. Will these harm my cmos chips. I'm getting some 470k resistors, so that should help. But would I need resistors if the LEDs are 3.2V? Also should I only connect these to the outputs of the cmos chips? Many thanks for a great video!

@primalvengence8443 4 ай бұрын

what a great video. excellent explanation. Question what if i wanted to use only 5 leds do i take output 6 and send it back to 13?

@Anton-wc7lb Жыл бұрын

Hi! Thanks for the video, very cool! :) Do you know if there is a way to modify the circuit to make the LEDs give of a short flash instead of being turned on for a duration of time? Or in other words, shorten the duty cycle of the 4017 for when the LED is shining?