LED Strip Dimmer Circuit

[@Creativecreator]

Hope you will Like this Easy Circuit Visit: circuitbest.com/led-dimmer-circuit/

[@noobsaibot7877]

LOOOOOOOOOL NOOOOOOO. WE NEED 240 VOLT DIMMER NOT 12V OR 6 VOLT.

[@lubomirnovak9628]

This circuit can not and will not work properly. You clearly do not understand how this things work...

[@DubaRuf]

Hi, thanks for video! Imade the circuit, it kinda works, but, the problem is the led is not as bright as connected straight to power supply when turned full power. Any solution?

[@John1960Video]

I found that the circuit needs 4 volts to open fully, so my 12v power supply goiong thru the circuit only outputs 8 volts. "This circuit uses 4 volts to open the gate, so my 12v power supply delivers only 8 volts to the LED strip. It seems to me that a MOSFET requiring less voltage to open the gate would be much better for my application."

[@jastriarahmat8813]

Is this energy efficient? Compared to using pwm?

[@makoado6010]

haha. nope.

[@gaurangvarawdekar2022]

Will led glow full or 10% less?

[@engician7620]

Is this voltage based dimming or frequency based dimming ?

[@jovanzacevski]

Hello Can i use this on automotive bulb ? I want to run with this one bulb of 12v H1 55W but at 6V, is it safe ? That would be 23W and 9 amps right ? I will put a heatsink on the transistor though. Thank you!

[@brx5067]

Can i use IRF520 instead of IRFZ44N?

[@Creativecreator]

If it is n channel mosfet then yes

[@buas7]

Also works with 24v?

[@oliverlow5349]

@buas7 I was wondering the same. Did you get any results?

[@John1960Video]

This circuit uses 4 volts to open the gate, so my 12v power supply delivers only 8 volts to the LED strip. It seems to me that a MOSFET requiring less voltage to open the gate would be much better for my application.

[@TheMdahora]

Is the mosfet really necessary? I wanted to use this circuit only with the potentiometer. Would it work?

[@MiftahulHD]

Potensio 250k di ganti 100k bisa ?

[@sfh294]

No need for a DM13A unless using PWM on the gate pin to control a higher voltage /current source than the PWM can out put.. kinda like a relay.. not trying to be mean just stating the obvious

[@yprastyo33]

can we use led SMD5050 or SMD4014 (12 v also ) ?

[@ayushdev4834]

My led has white, red, green, yellow 4 wire, how do i connect these?

[@rajamohamed319]

Hi hello dimming control working in put v12. the output volt not coming 12v volt draping..? ?

[@tkalcec874]

I created the circuit but it's not so bright when it was only connected to the power source

[@freekingawwsome]

That would be cool for under a car

[@darkgift3127]

*Elıneze sağlık teşekkürler*

[@wyatt6905]

I have also built it and it works I am so happy

[@Creativecreator]

Thank you so much 🥰

[@wyatt6905]

You do it soooooo well stay the way you are

[@wyatt6905]

I would even send you a picture of the circuit and maybe 20 minutes of it and it works

[@Creativecreator]

Send me on my instra id or fb. I willl be happy to see 😁

[@wyatt6905]

And can delete it immediately afterwards Hann you have it then

[@Davi-te2mi]

Can you use it also for RGB ?

[@caddyguy5369]

That's what I'm working on figuring out. I need to dim custom RGBW with the factory dimmer switch which is a 0 - 5 v potentiometer. have my doubts based on my experiments. I tried just putting a 5k pot on the 12v and it worked to an extent, but the problem with RGB was it would only dim to an extent then all colors except red cut out because the voltage gets too low. I replaced the pot with a PWM fan controller and had better success since it maintains enough voltage to fire all colors. I am doing more experimenting. I am using a combination of RGBW for the cluster and other backlighting and RGBCCW for dome lighting / interior lighting.

[@PrajeshMishrikotkar07]

What is downside of using mosfet and potentiometer to dim 12 v led strip. (comparing it with pwm dimming)

[@swalker157]

It’s not as power efficient. He’s just using the mosfet as variable resistor.

[@gloria0356]

Mas gimna klo lampu 12 v dn rakainx gimana itu untuk di motor yag tdk pake AKI MOTOR

[@gooddesign9991]

i dont get it why you put positive on drain and source in N channel mosfet

[@KY-ep6yh]

muy buenos videos... podrás hacer uno para el auto 12v de una tira Led que prenda con una intensidad y al apretar el freno se intensifique... 👍👍👍

[@jorgeraulalderete9821]

Eso es fácil. Si querés mándame un mail a [e-mail]. y te mando un esquema.

[@valerylovehouse]

Здорово! А какую нагрузка держит?

[@MACYNET323]

How much max current this mosfet support?

[@ElectricCreative]

mosfet it's so power full

[@Creativecreator]

yes

[@puneetpal6539]

Why mosfet is required?

[@АндрейТитов-г2б]

Эта громкая музыка заставляет меня страдать.

[@narayanarajugvvss7839]

Bro to reduce 12volts to 1.5 volts which value potentiometer we have to use

[@Creativecreator]

100k to 200k any

[@ericcaldwell3584]

Does it use PWM?

[@georgementzikof3549]

No

[@ahmeddahmani2662]

bravo morroco

[@electronic7979]

Very useful project 👍

[@Creativecreator]

Thank you so much friend!! 😃

[@senjolken9079]

Можно и без мосфета, биполярного транза, и потенциометра на 10ком за глаза. Мосфеты дороже раза в 3

[@Creativecreator]

да, вы правы, Mosfets дороже, но вы можете использовать биполярный транзистор. но текущая пропускная способность будет низкой.

[@Vlad_4572]

@@Creativecreator , мосфет же эффективен только в полностью открытом состоянии.

[@Садитесьиставьтеногинапедалиуп]

Ты крут.

[@Creativecreator]

Большое спасибо, пожалуйста, подпишитесь ..

[@vlastelin_dobra]

Мосфет не греется?

[@prabha2z649]

This circuit only 8 volt output , I required 12volt 2 amp

[@MH_1624]

बेक ग्राउंड ऑडियो इतना कातिल है की.. वो सुन सुन के...मैने आधा विडीयो बीच मे ही छोड़ दिया। 😂

[@pendekarzabong1160]

what video editor u use?

[@Creativecreator]

FCPX and Adobe softwares

[@pendekarzabong1160]

ok.thanks

[@freekingawwsome]

@@Creativecreator it's ok if these are a year old . Your videos are well watched by myself . Very nice soldering . I've never been so neat at soldering . Ever since electronics in school almost forty years ago I still never purchased a nice soldering iron lol

[@dhimande2646]

Nice

[@Creativecreator]

Thanks

[@niteshjaiswal3263]

Sir ji aap zero point pcb pr banaya karo ...

[@Creativecreator]

ok

[@Creativecreator]

Dot call me sir I am as your friend Dear.... 😀😀

[@niteshjaiswal3263]

Bro mujhe apka channel achha lagta hai.. best electronic gadgets .. me sirf 3 channel dekhta hoon electronic gadgets ke liye 1 . Aap ka 2. How to bro 3. Electric creative

[@anirbanmajumder2035]

How to work this

[@joaoreinaldo1213]

Cara acredito que você não sabe o que está fazendo, esquema diferente do que você tá fazendo, não foca a câmara direito, e não responde as perguntas.

[@ashiyadav8697]

Ok

[@drssound5273]

ජයවේවා යාලුවනේ කස්ටිය අපේ පැත්තෙත් එන්න ආවට පාඩු නෑ

[@dyushametelkin]

Че это за каракули?

[@drssound5273]

@@dyushametelkin Hi frend ...nice vedio Watch my channel Good luck 🙏🙏🙏🙏🙏 🔉🔉🔉🔉🔉🔉🔉🔉🔉 🎛️🎛️🎛️🎛️🎛️🎛️🎛️🎛️🎛️

[@ritaisabel8665]

Good

[@Creativecreator]

thanks

[@juniuschristianh.1693]

12v in drop to 8v out😂

[@sfh294]

I was hoping to find a good video on dimming using the Gate pin of a MOSFET and PWM instead, we've got this guy over here soldering a potentiometer directly to the MOSFET 😅

[@bassmekanikproboosterz7791]

Soporta corriente d 24v?

BassMekanikPro Booster search the spec sheet for the mosfet.

[@Vlad_4572]

Автор, а что за бред на превью? Только из-за него зашёл посмотреть. Кстати, видео не информативное, припаиваешь проводки, которые идут, не понятно куда. Нет наглядности. Зачем ты это сотворил? Короче, видео никчёмыш.

[@SRCN999]

its not working....