LED Transformer teardown and repair - is it fixed?

  Рет қаралды 8,550

backofficeshow

backofficeshow

2 жыл бұрын

LED Transformer teardown and repair - is it fixed?
If you would like to buy me a coffee or support the channel you can do so via Patreon at / backofficeshow
I do have some bits and pieces on my web store at backofficeshow.com
Please note: As an Amazon Associate I earn from qualifying purchases. As such links to Amazon products within this video may fall under this. Thanks to all of you who use these links and help support the channel - you are fantastic!
Thanks you lovely people, and keep on tinkering!

Пікірлер: 14
@naynayeaves1342
@naynayeaves1342
Thank you for such a helpful video
@wimwiddershins
@wimwiddershins 2 жыл бұрын
If it's flicking on/off, it's often the switching chip reboot looping because its own little power supply is failing (small capacitor).
@oluwasegunoladapoemmanuel3693
@oluwasegunoladapoemmanuel3693
100wt bulb driver giving out low voltage , can capacitor cause it
@pa4tim
@pa4tim 2 жыл бұрын
Simple, measure the cap with a real LCR meter at 120 Hz, note the Dissipation factor stated as tan delta. Look up the datasheet, there they state the new DF and the "bad" value at 120 Hz. This is the only good way. ESR is not stated in the datasheets because DF is used for decenia and does a better job. ESR at 100 kHz is sometimes used in datasheet for SMD caps. In most datasheet nowadays they also state the impedance at 100 kHz. For bigger caps the reactance is very low so the impedance is for most made by the ESR. However, ESR is frequency depending and at 100 kHz big caps can be inductive instead (look up SRF, self resonance frequency) On average, a very rough estimation, the ESR is at its lowest value around 30 - 40 kHz but can vary wild because of the many sizes.
@Mentski
@Mentski 2 жыл бұрын
Rubbing his hands all over the caps like some kind of MAD LAD.
@rhiantaylor3446
@rhiantaylor3446 2 жыл бұрын
I must admit I thought that was the only electrolytic cap on the line side of the regulator (i.e. after the rectifier and common mode filter inductor) and so I thought it would have 340v across it and, given that the replacement was rated at 50v, I rather expected it to go bang.
@andreiciora2765
@andreiciora2765 2 жыл бұрын
Wath happened with your shugon t26
EEVblog #1091 - LED Studio Light Repair
18:39
EEVblog
Рет қаралды 82 М.
Exploring a faulty LED driver (with schematic)
15:34
bigclivedotcom
Рет қаралды 89 М.
Clowns abuse children#Short #Officer Rabbit #angel
00:51
兔子警官
Рет қаралды 79 МЛН
Useful gadget for styling hair 🤩💖 #gadgets #hairstyle
00:20
FLIP FLOP Hacks
Рет қаралды 9 МЛН
LED Driver Teardown and Repair - Let there be light!!!
14:40
One Electron Universe
Рет қаралды 10 М.
Transformer Repair {Depotting} Lets Look Inside!
47:13
Mr Carlson's Lab
Рет қаралды 194 М.
How to Troubleshoot LED Drivers
4:18
Magnitude Lighting Inc.
Рет қаралды 18 М.
LED Driver 101
7:14
ACIPOWER
Рет қаралды 165 М.
Fixing my bench light
9:49
bigclivedotcom
Рет қаралды 80 М.
Failed 24V 10A power supply repair
22:11
DiodeGoneWild
Рет қаралды 88 М.
(Flashing content.) Repair of strobing LED power supply.
12:44
bigclivedotcom
Рет қаралды 292 М.