Let's Resin Epoxy Resin Box!

[@michellegarza9541]

This is super cute! All the people I watch that do resin use the isopropyl alcohol. They spray into the mold, they spray after putting the resin in, squish the sides of everything, some have the bubble machine, I can't even remember the name of it 🤦...bubbles are everyone's nemesis! You did a great job!

[@judy1111]

Love the box. So cute. That would be a cool nail set. 🩷🩷

[@Sabyscorpioncina]

so cute... simple and charming... well done you are a beautiful soul, it shows in all your works!

[@robinrowe8025]

Love the box you did a great job

[@ajax3630]

too cute ❤ Next time, after you mix the epoxy let it sit for about five mins. The epoxy will degas to the top and pop on their own. Then you can pour. Spray with 90% alcohol or a heat gun if need be. I work with resin.

[@KitschyKittenStudio]

Hi! You can try a few things for bubbles. You can let the resin sit for a bit to let the bubbles come to the top (not too long, though, or it will cure in the cups). While it’s sitting, you can spray the top of the resin with isopropyl alcohol every once in a while. You can spray your mold before you pour, too. They will always stick to edges, so doing this helps with that. For the rim of your box mold, you could separate the sides and spray down into it. Alcohol isn’t great for silicone, but I’ve not had any issues this far. Using a heat gun/ hair dryer/ long-neck lighter after poured can help with any bubbles that come up. 😊 Hope that helps! This is a beautiful project! I love the Mylar flakes!

[@KitschyKittenStudio]

Oh and you can run a small brush or a small stir stick around the rim to help dislodge those bubbles.

[@marthatownsend7702]

turned out very cute, love the flowers!!!

[@georgiastewart4479]

Shared. Love the box, and the mylar. I've seen some people spray isopropyl alcohol on the resin after filling the mould, or use a micro brush and go all around the edges with it to remove bubbles. I hope this helps!

[@Thebutterfly2018]

So beautiful! 😍 you did amazing with the resin and art 👏

[@MsFresh619]

Great box love the design on the top

[@martinaritrovato3261]

Missed you Natalie, hope you are well. God bless you

[@amandahales3331]

Love it, the mylar looks awesome xxxxxxxxx

[@rhondaarmstrong1405]

Great video. Love the resin videos. ❤❤❤

[@angelarobertson7004]

Super cute!!! I love it!

[@jacquelinedimattia774]

Super duper cute Nat !

[@sherryskewes]

I dont do resin crafts but my daughter in law does & everyone I have watched use a lighter for small molds or a butane torch for bigger molds❤

[@melissaguthrie1254]

Never torch a mold hun, it can fuse the silicone to the resin and ruin the mold.

[@BogArt1]

To avoid the bubbles holes in the border of the boxes, just put a little stick around the ledge to help

[@Ladymaskt]

Oh!!! That box is Soo pretty 😊Great job Natalie 💜💜!! You always have such great designs for all the work you do!! 💜💜🔥💯🔥💯

[@carronmoreton9385]

You did a lovely job of that x

[@leannenolan4181]

I thought those flowers were stickers! They amazing!

[@poohbear5007]

Oh my gosh!!! I love the box. The mylar with designs you did is amazing. It's so cute!💐❤ 🌸

[@Pheonixnailz]

The mat with the texture is to face the table. If you don’t need it to hold a project steady and a long neck lighter go over lightly to pop the bubbles

[@laviniacontraro4705]

I'm new at resin, I've found sitting the cup of resin in a bath of warm water or a heating mat for a couple minutes

[@marthafinizio5865]

❤❤❤

[@nailsbybramble]

Cute 😍

[@cindybrienze8723]

Beautiful work on this! Love the hand painted flowers! I am going to make this as a case for dominos, but I need to know before I pour them which one is the cover. Is it the deeper one or is that the bottom?

[@craftingheaven2501]

Heat gun gets rid of bubbles easily

[@FabulousLife615]

Love!!🩷🩷

[@alicemoore930]

I've seen other resin artists use a heating gun to remove the air bubbles

[@soniabird6951]

Hi Nat, I watch a lady called Julie, look for pouring your heart out, 🥰🥰🥰