I've also put few centre pop marks in worn area as well as using retaining compound in other situations
@biarbisa26292 жыл бұрын
Hingga sekarang loctite apakah tidak ada masalah
@friendsylz10384 жыл бұрын
Thannnksss for the vidéo
@rechtsgelijkheidvooriedere94193 жыл бұрын
RTFM: apply on both sides!
@ahmedhaiba-ng8dzАй бұрын
Does it fasten it or just prevent shaking
@pilotsrc-aeromodelismo6 ай бұрын
Hello, what's the difference between the 638 and 648?
@adamwallis21406 ай бұрын
Not sure to be honest with you mate without looking into it but I would guess they'll be a different curing time or higher working temperature 👍
@mudslinger1m2 жыл бұрын
Any report on this repair? Thinking about doing this on my Snowmobile, PTO Bearing has some slight wear in the case. was going to just put a LIGHT little coat....
@adamwallis21402 жыл бұрын
Sorry for the late reply mate taken me way too long to get it out and ran in but so far so good seems to have done the job ✊🏻
@FIRE-tv5ox3 жыл бұрын
Why use 638? Loctite 620 is meant for hot temperatures
@giannhsst2 жыл бұрын
Loctite 2620 is even better
@johnnielsen5076 Жыл бұрын
Agree. I have used 620 forever no issues. Loctite website even states for transmission housing bearing retention etc. Higher temperature resistance. 638 should work o.k. though.
@CortezMotoX3 жыл бұрын
How this work out? Going through the same thing I spun a bearing on the case
@adamwallis21402 жыл бұрын
Sorry for the late reply hope you got yours sorted, mine has been spot on still running fine 👌
@bigbert1119 Жыл бұрын
How is the repair holding up? My Driveshaft bearing is rotating in my case
@adamwallis2140 Жыл бұрын
Yeah still going strong no problems so far and it's been ridden hard 👍🏻
@MyJordan201 Жыл бұрын
how long time can use for the bearing house on the crankcase??
@adamwallis2140 Жыл бұрын
Not too sure to be honest this has been in now for just over 2 years and still fine but would depend on how much it gets used as well I guess 👍🏻
@j.young_rass81982 жыл бұрын
Wondering if this have worked out ?
@adamwallis21402 жыл бұрын
Yeah worked a treat still going strong, the bike was out again on Saturday just gone (17,9,22) 👍🏻
@hur00043 жыл бұрын
How did the bike go mate? looking to do the same thing on my Sherco 300SER
@adamwallis21403 жыл бұрын
In all honesty mate I've still not had it run in yet I've had it fired up a couple of times and it's been fine but obviously not the same as ringing it's neck round the track. it's deffinatly worth a try 👍🏻
@dale2079 Жыл бұрын
Having the same problem with a gearbox, how did this repair hold up?
@adamwallis2140 Жыл бұрын
It's been spot on mate still going strong now, hope you get sorted 👍🏻
@dale2079 Жыл бұрын
@@adamwallis2140 hi thanks for replying your video and info has helped me alot.
@troymortimer34873 жыл бұрын
If you need to remove the bearing in the future, will it still be pullable? Or is it glued tight
@petermelnikov6822 жыл бұрын
there is a loctite 641 that has medium strength, so you can remove it with manual tools
@LBCAndrew2 жыл бұрын
Apply enough heat and it will come right out. Operating temperature of Loctite 638 is 180'C. So above that and it will begin to soften.
@dejv11112 жыл бұрын
Yes, you can disassamble the bearing later. You have to heat up it with higher temperature.
@AAhshitsun2 жыл бұрын
Do you think this will keep my inner race from spinning on my ski doo pto bearing? Its a low mile sled but went to grease the pro and noticed the inner race moving.
@adamwallis21402 жыл бұрын
Couldn't say 💯 to be honest depends what's taking most the load the inner or outer race? On mine the inner is taking majority of the load and I've glued the outer, if your inner race isn't supposed to spin an the outer is taking the load its definitely worth giving it a go. Mines still working a treat 👌. I've no experience with a skidoo though 🙆🏻♂️. Hope you get sorted 👍🏻
@richardhill2836 Жыл бұрын
Look at Loctite 680
@juras92414 жыл бұрын
It's still working? or have any problems?
@adamwallis21404 жыл бұрын
Hi, I've had it fired up once and it was fine I'm just waiting to get out and run it in, as soon as I do I'll put a video together 👍🏻
@alexrands25803 жыл бұрын
@@adamwallis2140 and... Where's the report back son?