This is a video showing the cheapest way to lower an 86 Chevrolet C10 pickup truck by flipping the rear axle installing drop spindles and cutting the front coils
Пікірлер: 180
@dirtyburd712 жыл бұрын
Someone might have mentioned this in the comments already but drilling a new hole in the spring perch, moving the axle back about an inch and a half, would have centered the rear wheels in the fender opening and kept the drive line modification off the table. :)
@Sleeperdude2 жыл бұрын
That’s true thanks
@new_oldstock Жыл бұрын
Around the time you were lowering this, I was un-lowering a squarebody suburban. I had a heck of a time finding stock spindles, ended up using some from a G20 van. Love the videos!!!
@Sleeperdude Жыл бұрын
Oh man we could have traded spindles
@crbarreno23113 жыл бұрын
Great video watched it a few times before I tackled mine. It was super easy after watching this video.
@headlesnorseman7012 жыл бұрын
the most impressive part is that you got those leaf spring bolts out without cutting them lol
@Sleeperdude2 жыл бұрын
Yeah they can be a pain
@TC-dw6wg Жыл бұрын
Josh glad you didn’t let all the negative BS get to you. Keep being you brother!
@Sleeperdude Жыл бұрын
Thank you
@hdsquarebodyandmore.35923 жыл бұрын
Hey just found your channel enjoyed the tips especially the TSC flip kit... keep the videos coming.
@LKRS1112 жыл бұрын
I cleaned spark plugs 2wice a day just to get to work and get home my 305 was burning oil... So I saved up and bought a new 350 worth every penny .
@Sleeperdude2 жыл бұрын
350 is a much better setup for sure
@siberian08433 жыл бұрын
Bro that truck looks so good man, I just bought a 81 custom deluxe for restoration keep it up!
@erichuff25382 жыл бұрын
Dude it sets good. I never knew how to shorten a drive shaft like that 👍-- thanks for the lesson.
@Sleeperdude2 жыл бұрын
No problem thanks for watching
@pontiac411 Жыл бұрын
Lowered vehicles are really good for looking at
@hippiemiller4 жыл бұрын
Very nice bro you got lucky I had to buy all new brakes and barrings on my 89 with ruff country drop spendals
@RyanRyker Жыл бұрын
Thats a great looking truck, i love all the older models.
@Sleeperdude Жыл бұрын
Right on
@TheREALOC19724 ай бұрын
To avoid the tire ride cut out a couple inches further back from where its and then add a 1/4" tall of steel to the piece you cut out and weld it back in, you CAN just heat it up and hammer it up out of the way but that looks like hell, by adding metal it just looks cleaner and looks like something the factory might have done.
@Sleeperdude4 ай бұрын
Ok thanks
@TheLaidbackBiker3 жыл бұрын
You did a great job! Truck looks awesome.
@Sleeperdude3 жыл бұрын
Thanks
@robertroth6183 жыл бұрын
I had a similar setup on my 86 long bed For tires, I ran a 245/60/15 in the front and 275/60/15 on 8inch rally rims.
@tom-ehill2713 Жыл бұрын
Just found this one!! Y'alls videos just pop in out of thin air!😁😂😂😂
@Sleeperdude Жыл бұрын
That’s funny.. you should go to my channel click on the video button then scroll to see which ones you may have missed!
@tom-ehill2713 Жыл бұрын
@@Sleeperdude OKee dokers!
@joshschonfeld3675 Жыл бұрын
That's pretty typical for AutoZone to sell you Autolites for a Chevy and to have a missing plug wire lol cool video though and I've never heard of that trick you did to shorten the driveshaft! I'm buying my old 79 squarebody GMC back this weekend and doing pretty much everything you did in this video 💪🏼
@kbtruck65blair643 жыл бұрын
If that truck starts to run rough, change the plugs to AC plugs. Autolite is mainly a Ford plug.
@bobtucker8875 Жыл бұрын
The truck looks good. But now it's only good for hauling a half gallon of milk home. Thanks for sharing 😊.
@Sleeperdude Жыл бұрын
🤣
@coreycoate2910 Жыл бұрын
Love this video. Truck looks great!!
@Sleeperdude Жыл бұрын
Thank you
@exb9sx2 жыл бұрын
Thanks for the great video , really helps for a newbie.
@Sleeperdude2 жыл бұрын
No problem thanks for watching
@wsttxC10_454 Жыл бұрын
Don't take this as criticism I enjoy y'all's video content but that is totally the wrong way to measure how much to cut gm coil springs LoL 😂, the proper way is to take them both out then measure with a measurement tape and start from where the coil starts running it around till you get to the number of inches you want to drop it- 1.5 at the coil is 3 inches at the body. That's definitely a creative way to lower the rear and the fix the driveshaft problem never seen it done before that way I was impressed, I wish I knew how to weld lol 😂 Great video other than that keep it up brotha the truck looks great 👍
@Channel5053 жыл бұрын
looks great it sits just fine,, I'm going with 6-8,
@hoodmukbangs99933 жыл бұрын
Just bought a 87 c10 for $1300.I also have a long bed on mines but definitely looking to drop it quite a bit
@tommyhobbs75512 жыл бұрын
Good work. Looks good and it's worth a shit load more now than before!
@TimothyHigdonHiggs Жыл бұрын
You did a great job!
@juandunas2381 Жыл бұрын
Thanks for the info I got a 77 C10 that I will be doing this setup mine is long bed too 😎😎😎
@Sleeperdude Жыл бұрын
Awesome
@mattpack76602 жыл бұрын
I was scared watching you remove the rear springs...I thought they were under pressure and it would spring out...scary...a...oh and Autolite (Ford) plugs in a Chebby!? Champions...I think. If we don't learn anything else from you it's stick-to-it-tiveness and patience. Congrats on the 1 Million views on the tractor!!!
@Sleeperdude2 жыл бұрын
That’s funny thank you I appreciate it
@erichuff25382 жыл бұрын
Breather loos good ... drop spindles are awesome keeps the geometry right with a lowered stance. Love um..
@Sleeperdude2 жыл бұрын
Thanks
@slowshedgarage74093 жыл бұрын
Nice lookin Ol truck. New Subscriber
@cgnieves13 жыл бұрын
Definitely you did not needed the drop spindles.
@TheTileplace2 жыл бұрын
looking good rock on man
@Sleeperdude2 жыл бұрын
Thank you
@jmrramirez13 жыл бұрын
I luv it.it looms great
@Shadetreejr19672 жыл бұрын
My granddad had a 79 Silverado with a 305, out of 8 Cylinders 5 of them had anti fowlers on the plugs....lol motor was weak as crap and smoked like a train!!! Great memories though!
@Sleeperdude2 жыл бұрын
Yeah I am not a fan of a 305
@toddjohnston4788 Жыл бұрын
Looks great 👍
@Sleeperdude Жыл бұрын
Thank you! Cheers!
@JUSTPEED4 жыл бұрын
Afro wheel love it that's what I call it too!!!!
@michaelreece4583 жыл бұрын
Very cool indeed. Nice job.
@Sleeperdude3 жыл бұрын
Thanks again
@ihatesjws66910 ай бұрын
For those of you who want a real answer, for every 1 inches of free height cut at the spring is two inches at the body.
@Sleeperdude10 ай бұрын
Ok thanks
@Dallascowboys962762 жыл бұрын
looking good bro superdude
@Sleeperdude2 жыл бұрын
Thank you
@kCI251 Жыл бұрын
You succeeded in lowering the value, that is for sure.
@darrenredenbaugh10123 жыл бұрын
If you buy a flip kit you dont have to weld new perches, or shorten the drive shaft, and the added bonus of new u bolts, instead of reusing worn out factory u bolts from the 80's
@Zanehoward883 жыл бұрын
If you he would have just drilled a half inch hole behind the center hole in the new perches you dont have to do anything to the drive shaft.
@marcushopkins59822 жыл бұрын
I just seen this and thank the lord haha I’m lowering my 87 and I didn’t want to shorten the shaft! Thanks!
@andrewp.15563 жыл бұрын
Great video! Now go get some air bags and make another video installing them so I see how its done Lol
@brianbvachek32193 жыл бұрын
Fuck yeah man! This video was legit exactly how i slammed my 88 s10. Couldn't fit a pack of smokes under the front bumper lip on pavement lmao That truck turned out sweet man!
@Sleeperdude3 жыл бұрын
Thanks.. I love a lowered truck
@douglasbrodock5732 жыл бұрын
A long time ago an old friend had an s10 blazer we put a vortec 350 in a lowered it LOW. Had to c notch it. It would wheel hop terribly..... I had 2 nice xjs at the time. One day we were sitting having a drink. And I had an idea. I told him to go to the local offroad shop and get a used set of xj springs. We used the main leaf from the blazer and then used the rest of the xj leafs and was able to rid of the lowering blocks. It never even rode that good stock and it launched great with the xj leaf pack.
@mackjenkins77212 жыл бұрын
Man you did a real good job on Lowering the truck man. Man she look real good. For somebody doing it for the first time you did excellent job man. Sleeper dude I have a question man? Is Your town Riceville located off of Interstate 75 down by Chattanooga Tennessee? I did enjoy watching you lowering that truck man.
@Sleeperdude2 жыл бұрын
Yes that is where it is thanks
@mackjenkins77212 жыл бұрын
@@Sleeperdude oh man I just came by you last night on my way to drop a load off and my wife in New Orleans for the hurricane victims. Man I had driven by you so many times. I just drove by you two weeks ago on my way to Alabama when they got hit by the hurricane. Interstate 75 and 40 are my traveling interstate. Man that is so awesome. Man I would love to meet up with you someday that will be so awesome.
@oldschoolman65722 жыл бұрын
Love the video, I had a question about the spindles, what brand did you get? I know they were inexpensive I’d like to get the same ones Amazon?
@Sleeperdude2 жыл бұрын
It’s been so long I don’t remember sorry
@johnnywrench55793 жыл бұрын
I use to run mine with no springs at all on the bumpstops and flip the rear .1/4 steel bent on both ends get welded under the saddle with the hole drilled putting the pin toward the front or you will blow the tailshafts off
@anthonymccoy87713 жыл бұрын
Again that’s stupid riding on the bump stops that will knock parts off
@joeroe28393 жыл бұрын
@@anthonymccoy8771 i lower trucks as full time job and i see this all the time on these c10s lol i was just guessin they were dropped back in the 80s but now we got full kits 🤦🏽♂️🤦🏽♂️
@robquest64992 жыл бұрын
@@joeroe2839 hi joe , what drop kit do u recommend for a 82 chev short bed ,I want to do a 5/6 drop ,I want to install some staggered 22” AR salt flats wheels ,,what drop kit should I go with and should I do the c notch?
@joeroe28392 жыл бұрын
@@robquest6499 I just did a 6-8 drop w a small rake outback ..and yea I recommend a notch if goin that low just incase u fill.up the back w something heavy . I like crown suspension if u on a budget or belltech springs/mcgaughys spindles
@PhillipHall01 Жыл бұрын
Good job! I am getting ready to do something like this to a 77. I don't want to spend a lot of money on new modified aftermarket parts as recommended by another channel who is sponsored by those parts companies. There is nothing wrong with replacing everything with new modified parts designed for this purpose, 'if' one has the 'much' extra money to buy those parts but money can be a hurdle at times.... It's nice to know it can be done this way. How does the truck ride now? I know you learned a lot by doing this one, this way. If you had it to do over again would you go the same route, or would you recommend going the high dollar new parts way ? I trust your judgement and experience which you have gained 'by doing'! How does the truck ride? I hope you can find time to answer my questions which will be 'very' helpful. PS How is Ralphie's Camaro coming along? Yall are a blessed family. Keep up the good work and God Bless!! Phillip Hall
@Sleeperdude Жыл бұрын
Yes I would do it the same way. It rode pretty good actually
@PhillipHall01 Жыл бұрын
@@Sleeperdude Thank you SO much!!! Phillip Hall
@pandaliquidationaz80332 жыл бұрын
great video thank you
@Sleeperdude2 жыл бұрын
Thank you for watching
@leviblocker1761 Жыл бұрын
Did you c notch the rear ? If not … what kind of clearance did you end up with ?
@dontasmith22413 жыл бұрын
You have a link for the drop spindle
@bonethang3744 жыл бұрын
How do you line up the pigtail on the coil spring with the D in the crossmember if you cut a coil and a half? Wouldn’t it be misaligned if you cut more then one whole coil increments? Thanks in advance
@Sleeperdude4 жыл бұрын
You can spin the top of the spring in any position to make it line up with the groove in the lower control arm
@GreggGonzalez-ei1gu2 ай бұрын
Awesome 👍
@EFTProf Жыл бұрын
Can someone please tell me what is so wonderful about dropping the height of vehicle suspension, when it is set in the factory @ the optimal height for the car/van/pick-up?? They look awful and perform even worse!!! My opinion I know, but yo don't find anything like that in the UK. See you soon (if I can work out the name-changes..... 🤓
@gunnerkemp77053 жыл бұрын
Did you use the stock shocks in the front in rear?? Watched the video a couple times, sorry if I missed a part where you said it!
@Sleeperdude3 жыл бұрын
Yes I used the stock shocks
@BornToBeFamed2 ай бұрын
Im shocked you didnt cut those front bump stops🤣 but might as well buy new tubluars at that point. Im riding 295/50/15s i cut 2 coils. Im 5.5/6 easily . Looks sick but I need tubulars. I love my tiny rake.. mine doesnt rub at all.
@rc4lifebnsf Жыл бұрын
Link for leaf spring perch’s?
@stevonkoch80023 жыл бұрын
guess you should of cut coil after drop spindles. half coil and you wouldnt have rubbed.
@davidnelson1872 Жыл бұрын
I would've left the front were you had it first
@oldmanintheshopbuiltnotbou87263 жыл бұрын
subbed back truck looks good
@MrHross083 жыл бұрын
Did you ever find a wheel and tire combo that didn’t rub top of the wheel well? Just did 2.5” spindle and 3” drop springs on my 82 and having same issue.
@Sleeperdude3 жыл бұрын
I ended up putting some spring rubbers in the front springs and that fixed it
@joeroe28393 жыл бұрын
Do some slosh tubs look em up , i drop trucks as a full time job and when i go beyond a 5 drop we install those to clear any setup there perfect or take off your innner tubs and ride
@garfixit Жыл бұрын
Nice
@Sleeperdude Жыл бұрын
Thank you
@luperojas2817 Жыл бұрын
Thanks
@shartne Жыл бұрын
Looks good. I would not want to drive it on a rainy day though probably might flood out with no inner fenders.
@Sleeperdude Жыл бұрын
👍
@davewallace82192 жыл бұрын
re coil the front.. end... add 2 inches back..the geometry has been radiclly changed..
@Sleeperdude2 жыл бұрын
Yes
@oldschoolman65723 жыл бұрын
Sweet video, I’m going to lower mine , long box I got Belltech 6852 kit I’m not notching, I don’t want to ruin the frame. Is it worth lowering does it Ride better?
@Sleeperdude3 жыл бұрын
I like how it rode but I am used to lowered vehicles
@oldschoolman65723 жыл бұрын
Did you have any clearance issues without notching it?
@Sleeperdude3 жыл бұрын
No I didn’t
@oldschoolman65722 жыл бұрын
I lowered mine still lots of clearance, not notched, rides soft which was my goal. Used shorter shocks
@stephenhester41182 жыл бұрын
I want to do the same to my pickup, but I thought I had to do a c-notch. How does it do without the c-notch?
@Sleeperdude2 жыл бұрын
Ours did fine … if you went much lower than what we did you would have to
@itsmephil22559 ай бұрын
Daaaaaaaamn that looks good slammed
@Sleeperdude9 ай бұрын
Thank you I liked it
@itsmephil22559 ай бұрын
@@Sleeperdude where is it now? Hope it's still being used
@lenghtofpull Жыл бұрын
Be careful using a grinder like that or you'll end up eating it l. Good looking truck
@Sleeperdude Жыл бұрын
Yeah for sure
@timbollinger32098 ай бұрын
That was the quietest I have ever heard Ralphie. So, did y’all sale this truck ?
@chuckh.22279 ай бұрын
I always drop my new spark plugs to adjust the gap
@refugio9539 Жыл бұрын
🔥🔥🔥🔥
@joshuajames39963 жыл бұрын
Put stock springs back in it and save yourself the headache
@davewallace82192 жыл бұрын
re build...and poss. re jet the carb...reset the choke also
@Sleeperdude2 жыл бұрын
👍
@GregFarrell-jp7im Жыл бұрын
Take the fat end of a baseball bat and roll the car truck for forward and backward and let the baseball bat top ride up on the fender well and I’ll push the fender. Well I’ll just enough to get tired of clear.
@davewallace82192 жыл бұрын
phosphoric acid is a good etching solution
@Sleeperdude2 жыл бұрын
Ok good to know thanks
@erichuff25382 жыл бұрын
Did you use marhide trim black ?
@Sleeperdude2 жыл бұрын
I honestly don’t remember
@troymccoy26542 жыл бұрын
I didn’t use the 2inch spindles it was low enough and I don’t want to take out the inner finders
@Sleeperdude2 жыл бұрын
Good call
@ethancroppermusic90832 жыл бұрын
I’m not gonna do the spindles but you best bet imma drop my c20 make it look like this.. I’m going for 3/5
@Sleeperdude2 жыл бұрын
Awesome
@johndaigle68285 ай бұрын
Did you leave original coil springs on?
@davewallace82192 жыл бұрын
good h.d. shocks will do...
@Sleeperdude2 жыл бұрын
😀👍
@jimthomas7772 жыл бұрын
SO ! Try R44TS AC Delco spark plugs
@Sleeperdude2 жыл бұрын
Ok thanks
@jimthomas7772 жыл бұрын
@@Sleeperdude , Oh yeah , Those two push bars on the front bumper or as I call them broken Teeth , I removed mine from my 78 Chevy Silverado and threw them on the shelf in my garage , it looks so much better and if I ever decide to sell it I will give them to the next owner and if he or she decided to put them back on its their choice , but as for now and it's mine , they are going to stay off , Nice looking truck Sleeperdude
@rc4lifebnsf Жыл бұрын
Link for the drop spindles?
@Sleeperdude Жыл бұрын
Sorry man its been awhile but I do know they were the cheapest ones on eBay
@TC-dw6wg Жыл бұрын
This video was done 2 years ago! No way I would remember or probably be able to find on flea bay. Thanks Josh for great video.
@dontasmith22413 жыл бұрын
What drop shocks did u use
@Sleeperdude3 жыл бұрын
I didn't change the shocks
@dontasmith22413 жыл бұрын
@@Sleeperdude do you know the brand you have
@Sleeperdude3 жыл бұрын
I'm not sure they were just what was on the truck I sold that truck months ago
@stevonkoch80023 жыл бұрын
why not clean up and paint the control arms once you had em out.
@Sleeperdude3 жыл бұрын
It was just a quick job to resell the truck
@johncantley78803 жыл бұрын
This video makes me not wanna lower my 85 anymore.
@gageandroshak4911 Жыл бұрын
Bruh why it isn't that much work
@timmiegregory6216 Жыл бұрын
@@gageandroshak4911 a1111111111à
@franciscogonzalez10943 ай бұрын
😂😂😂 lazys
@ryanbeyea28343 жыл бұрын
Hi
@Anders.W. Жыл бұрын
You said the T-word .
@mikerollins82724 ай бұрын
💯👍🙏
@johntoney-sn1fe Жыл бұрын
DUDE! forget the work on the truck!!! Please move those 4 gas cans outside BEFORE you start grinding!
@Sleeperdude Жыл бұрын
Good idea
@MrRickarriaga9 ай бұрын
autolite plugs?😒
@erikestrada293 Жыл бұрын
Auto lights? Why? ACdelco is for Chevy's
@edmunger5595 Жыл бұрын
Why would someone want to?
@oswingomez98123 жыл бұрын
Salta más que tú hermana
@johnnywrench55793 жыл бұрын
I can show you how to slam it without spending a dollar
@kevingarnet68223 жыл бұрын
Show us
@roywimsett28809 ай бұрын
Why would anyone want to do that it's not a Honda. So now it makes it as a truck useless.
@robertmoreno38683 ай бұрын
mine is lowed and still able to use it as a truck just brought a pallet of sod home
@raywilson800 Жыл бұрын
Way to ruin a survivor truck.
@thomaslyon2112 Жыл бұрын
You ruined that Chevy,unless you are going to sell it to a mexican😮
@Sleeperdude Жыл бұрын
Ok thanks
@bobbysilvers72132 жыл бұрын
Mess that truck up should have left the drop spindles off
@douglaslambert5793 жыл бұрын
Lot of work to make it un drivable. I know it’s popular but I don’t care for a truck sitting this low.
@Sleeperdude3 жыл бұрын
The guy that bought it drove it 3 hours home with no problems
@IronChief3 жыл бұрын
How to make your truck completely undriveable in just 25 minutes.