I found it easier to put the piston in the cylinder before putting the wrist pin in. Less screwing around i think.
@ChadMyers734 жыл бұрын
Thanks for the tip.
@daynemartin18073 жыл бұрын
I have buddies that are harley guys and they all put the piston in the jug just to the bottom of the oil ring land, seems to make assembly a lot smoother and less time that the flywheel is exposed.
@luisrey965 Жыл бұрын
What is the gap on the cam?
@draggerlane040904 жыл бұрын
So you rebuilt this with 94mm bore and left the top end stock. Wouldn't that choke the motor? I would go with kibblewhite diamond valves, kibblewhite diamond spring kit, with a stage 2 hotcams, Keihin FCR Carburetor. And for the exhaust I would do a full aftermarket replacement like a Big gun or Yoshimura RS-2 Series Slip on muffler with a FMF Powerbomb header. Then that upgrade will be complete. My experience you can't just change the jug and piston and expect performance gains.
@ChadMyers734 жыл бұрын
Stock cams and bigger piston and cylinder
@corylangille18698 ай бұрын
J/W, Have you done this already?
@ElioDiMaggio9 ай бұрын
I would like to get an LTZ 400, could you tell me what extraordinary maintenance it has? and every how many hours? for example piston
@ChadMyers739 ай бұрын
I didn’t care for those engines at all. Parts are becoming harder and harder to find.
@ElioDiMaggio9 ай бұрын
@@ChadMyers73 I come from the world of motorbikes where a piston is changed about every 60 hours, but with an LTZ I would use it in the countryside and in the woods, so I wanted to know if it is necessary to change the piston every few hours, and if so how often?
@ChadMyers739 ай бұрын
Just like all other 4 strokes they need changed about 50 to 75 hours. With 2 strokes being about 25 hours
@lt-z-quadnation66443 жыл бұрын
How was the chain to do? I’m wanting to do mine but reluctant to do it. The bike has very low hrs and I’m not sure it needs it but I know it couldn’t hurt.🥴😬
@ChadMyers733 жыл бұрын
I found it fairly easy to do just make sure and count your links
@emfl44374 жыл бұрын
Thanks for the video, this is an excellent resource.
@ChadMyers734 жыл бұрын
Your welcome!
@ltr_madness86864 жыл бұрын
I just rebilled mine and the anifrez part of the gasket broke and it is burning anifreaze
@GuitarGuys72994 жыл бұрын
Will there be a part 2 video?
@ChadMyers734 жыл бұрын
Yes ran into a issue...
@bayouboattrash5 жыл бұрын
YAAAAY TOOL TECH TUESDAY!!!!!!
@ChadMyers735 жыл бұрын
Will have some Olsa tools on today!
@jameshoffman82234 жыл бұрын
Chad Myers73 is there any bottom end rebuild video on the z400 I’m working on mine and running into problems assembling the transmission
@bayouboattrash5 жыл бұрын
Dude, as far as the weather it's not much better down south. I'm north bound in the Mississippi River and as soon as I came through I-10 bridge it was like someone flipped a switch. From heavy fog to 35 mph winds and holding. Mother nature is angry.
@ChadMyers735 жыл бұрын
Gotta love Ohio weather...
@bayouboattrash5 жыл бұрын
Lol, Louisiana isn't much better.
@GuitarGuys72994 жыл бұрын
Forgive me for the noob question, but what does the big bore kit bring the CC's up too?
@ChadMyers734 жыл бұрын
It makes it a 440 and the only dump ? is the 1 that is unasked.....
@germansantini25144 жыл бұрын
How much is the camshaft torque
@ChadMyers734 жыл бұрын
The caps get torqued to 10nm or 7ft lbs.
@luisrey965 Жыл бұрын
Grate video
@ChadMyers73 Жыл бұрын
Thanks for watching
@chrisd33993 жыл бұрын
Heyyy i have a question (might be stupid question) my exhaust cam was causing a ticking noise on my LTZ 400 i figures since im going in the engine and replacing it id doo a top end, does my cylinder have too be Rehoned ? Or am i aloud too just throw a new OEM piston in there with fresh rings
@ChadMyers733 жыл бұрын
I would say it probably depends on how much where are scarring is in the cylinder
@chrisd33993 жыл бұрын
@@ChadMyers73 thank you!!
@tobiasneureiter76255 жыл бұрын
Nice vid but where is the testfire?
@ChadMyers735 жыл бұрын
Well we found another issue with the engine that needs to be addressed with the cases. I will have more info soon. Thanks for Watching!
@danpmatz4 жыл бұрын
I have a Z400 that was parked about 4 years ago I drained all the gas and clean the carburetor could not get it to start I put a compression gauge on it and it is reading 0 I don't see how it could have blown up not running any ideas?
@ChadMyers734 жыл бұрын
Did you put oil in the cylinder and do a compression test that way also. If you do that and you then have compression then the rings are rusted and stuck. You'll just have to re-ring it. Hope this helps and thanks for watching!
@danpmatz4 жыл бұрын
@@ChadMyers73 do you think just stuck Rings would have it reading as low as 0
@ChadMyers734 жыл бұрын
Dan Matz Yes it is possible. Put a tablespoon of oil in the cylinder and recheck if still no compression than there is a valve issue.
@troymcconnell61474 жыл бұрын
i would put some pb blaster in cylinder and roll it down hill in highest gear without a spark plug ... should a break loose without any damage... works for me
@troymcconnell58323 жыл бұрын
@@danpmatz add oil to cylinder, with spark plug removed, find and transcend down big hill in gear, 3rd gear preferably, insert spark plug and wire, should fire up and be good
@jordanstanga13714 жыл бұрын
The Cummins intro😂
@ya_plohoy87174 жыл бұрын
Спасибо! Ты мне помог найти свою ошибку.
@nicolaealingna91704 жыл бұрын
hey nice video !!!! keep it going ...i just buy one ltz and anything you do can help me in having a good working atv
@ChadMyers734 жыл бұрын
Thanks for watching! It will be back in the shop soon for more work so stay tuned....
@the_ltz_guymaster79124 жыл бұрын
Who buys the cheapest piston always get weisco
@ChadMyers734 жыл бұрын
I did haha
@chrisd33993 жыл бұрын
I got weisco piston mine came un marked cant tell which in take or exhaust so idk if im putting my piston in backwards
@tfawcett025 жыл бұрын
I’ve been told Namura is a bad brand anybody else think 🤷♂️. Jus sayin
@ChadMyers735 жыл бұрын
I’ll be the 1st to admit I really don’t know much about the aftermarket world of these bikes. I found it on Facebook marketplace. 🤷♂️ Thanks For Watching!
@troymcconnell58323 жыл бұрын
i have been running Namura big bore kit for some time now ... no complaints here