Amazing Motor Greder Operating Techniques - Skilled Operator

This is the Amazing Motor Greder Operating Techniques - Skilled Operator safety first at work.
this videos for learning tools.
Thank for watching my videos!!
Please: SUBSCRIBE for more!!

[@lamarpye]

I’ve run graders 20 years and this is laughable 😂

[@darea4559]

I just started doing dirt 3 months ago and this is funny😂

[@ridgedbullet2420]

​@@darea4559I haven't even touched a grader and I know he's fuckin it up

[@rossfry1618]

Every bounce of machine is another corrugate .Slow down

[@brucedemchek3002]

15 seconds into the video I can tell you that this is NOT a skilled operator. At best he is just a "driver". Watch the machine bounce. He is traveling too fast. Improper machine placement, improper circle and moldboard position, no wheel lean. Pushing a large windrow, he should have had some articulation.

[@trvpgame7710]

Yeah lol this looks like a beginner really, it’s not even on a slope either so no risk in using articulation / wheel lean

[@هدالمطوف]

الشمري

[@daeeunkim1554]

Only past. . . No good.

[@alanlambert-bz4to]

Operator still learning. His teacher is in the cab with him.

[@brucedemchek3002]

@@alanlambert-bz4to Then why didn't this "teacher" tell him to slow down? Plus all the other things he was doing that needed attention. Believe me, I know that there are no two operators that do things all the same way, but there are things that ARE standard techniques. Those are all things that his teacher should have been addressing. You could read some of the other comments, and they were saying basically the same as I was. Some were nicer than I was in their critique, some weren't. I mean if your video is going to say "Amazing operating techniques, skilled operator", you should have had the "teacher" operating.

[@steveg2509]

What’s so extraordinary skilled about this?

[@NakedDave100]

Exactly, ground speed to high and machine was bouncing, wheels were not leaning towards the discharge side, skilled my ass!!!

[@kenwiese4828]

Just a dirt pusher. Final trim and and a water binder and there cutting to tolerances is a gun operated I should know my old man was one. No Lazer bullshit he needed

[@MrMan5014]

A good blade man never lets tailings roll off the leading edge of his blade…maybe if you are bulking and hitting piles but never when you’re finishing…this guy is doing good for just learning but he’s not an experienced finisher by any means!..these are the things you must go through as you learn…I was there too when I first started!..

[@arthurtomczak8474]

Trying to wear out the dirt?

[@lovejcdc]

Yeah that is just some dude that learned what lever did what and jumped out there lol and the guys on the rollers are hilarious 😂 they have no clue WTH they are doing 🤣 😆. Looks like an amusement park but the rides are equipment instead of carnival rides 🤣

[@Sugertoes420]

That's f×cking hilarious 😂 😃 And they have the sheep's foot packing gravel 😅

[@michaelburt1370]

The new graders are pretty quiet. I miss the loud roar of the older caterpillars.

[@callmewheels4806]

*SKILLED!? Are you kidding me!? This is a What Not to do video. Blade speed is Twice what should be (he’s BOUNCING!) , putting the windrow back into the previous cut, making passes on top of passes with NO SIGHNS of ANYONE OR ANYTHING checking grade (WHERE ARE THE GRADE STAKES!?) and the list goes on…*

[@adelarsen9776]

I'm not a grader operator but I have watched plenty of them over the last 30 years and this guy is rough.

[@woody5109]

A skilled grader operator makes sure the mole board is rolled back all the way, the machine stays intimate with the surface and there’s always material rolling off the end of the blade. This guy is a rookie at best.

[@seanduke2478]

I don't see the skill

[@لاالهالااللهمحمدرسولالله-ط6ذ9ذ]

kzbin.info/www/bejne/jaHKhpd5f9h7kMU👈

[@scottcampbell7513]

The only “amazing” thing about this is how much that poor grader is bouncing.

[@Sugertoes420]

Apparently they dont build anything to spec in what ever country this is

[@jenterasalimpodonpitas1786]

Support

[@alanlambert-bz4to]

You can see the instructor in the cab with the driver all through the vidio.

[@mohmmadjaseem5022]

Bhaiya hmm bhi grader operator h fast chalane ko bola jata h. Sub..Top nhi bn rha h.

[@hrv0.-]

Guys with sakai and hamm behind grader are not skilled,they dont drive their machine properly...

[@mandlenkosilucky9005]

Inexperienced contractor 😂

[@pdias3755]

I call this, roush to do slow work.

[@dwaynemarkowski8139]

Rough operator

[@OwenDowner-do6kn]

I love thi

[@babarhussain8811]

Good operator exelent 👍

[@UK.officia1997]

म I am a high scale grinder operator

[@رابحدرقاوي-م1ت]

Coman réparer les vérins de rotation du nifleuse chonpion

[@Polysingh_]

Conditioning. That's the standard bro

[@carolinesousa3747]

I love to watch the grader

[@Ardiofficial-tv8wb]

Sangat bermanfaat

[@JoseCarlos-gt7jd]

José Carlota Oliveira Reis

[@luisaguabil3239]

6años bem e você não vai dar clase virtualea me dijo q vaya 6años y no me voy a 9

[@hamzabenz6839]

My dream grader

[@OuedraogoPhanuel-vq7xd]

Cc moi je suis un conducteur de niveleuses mais je suis au Burkina Faso

[@MadanKumar-mk2fl]

Excavator operator ki vacancy h kya

[@duniakita1302]

Work for v ditch

[@UKMechanic-mr2kv]

not even spelt right! As for the workmanship...

[@JessicaClayton-d6x]

Yes I agree not an old school grader man. They don’t go fast but they only go over it once

[@alexmakau367]

Why the hell is he cutting a ditch like that.... This is laughable at best....😂

[@stevenblue3126]

Sorry, but I don't see a skilled operator

[@fidelmontollaiii7866]

sad part is he has a trainee riding with him. gonna have 2 non-operators now.

[@evildotirarentes5023]

esse emilho não deixa ninguem concluir seus pensamentos , mucha a oreia e fica calado emilho

[@elvispresley3234]

Horrible operator.

[@brianholland2916]

CAT lives matter!!!

[@ITSanART_WORK]

fastforward video😊

[@HilalNaddah]

لك ايرك معلم اه يا نمر

[@happymann839]

Ausgezeichnet 👍👍👍👍👍👍

[@josephpineda7442]

aingk....no good.

[@Josephpaulight-gv1pd]

Please i need grader to buy

[@رائدعمران-ح9س]

komatsu 655❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

[@carloslopes9514]

Muito bom mano

[@seanduke2478]

Try doing that North America

[@bjornjohnson6629]

My problem was digging to much but think I got it appreciate the video!

[@felipeflorentino1339]

nice work🎉

[@AZQ991]

mantap 👍

[@gayomeprosper8836]

Good job 🙏🙏

[@vtamilmaahren]

Good Job. Thank you brother. God bless you 🙏🏽

[@azizchkour6106]

Buen trabajo

[@taiseerhssn3979]

It is good operator very much good hi is skilled operator and cayenn

[@traoreadama7397]

Very well

[@blake7749]

The bouncing was cool. But hey, you got a army of rollers following