Maintenance Tip: How to Install a Packing Gland

[@jimnowinski2247]

was also curious about the location of the lantern ring, always on exams - thanks for showing procedure clearly!

[@ntwadumela374]

thanks for up-load. it's done well and gives a good fundamental on seeing what is going on when you need to adjust pump packing. thanks again

[@markthechiller83]

thanks a lot....i have always been confused about lantern ring...this made it clear.

[@GemmyHeart]

Main products: sealing gasket,gland packing,PTFE/graphite/asbestos products, ceramic fiber products, high temperature heat insulation and fireproof material. Free technical support (sealing, heat preservation, heat insulation, fire prevention problems) All products 1 piece can also be customized, 30 years of service experience, fast and safe shipping anywhere.😇

[@tonywong6026]

This job is called repacking the stuffing box(of a pump/a valve), not installing a packing gland .To do the job, new packings are pushed into the stuffing box and then held by the gland .🙂

[@hard6guard]

It is called " Gland " , to tight on and pressing the packing forward to seal on the shaft sleeve when leakage occur . I wish my answer helped you ..

[@robbiehobbs2009]

Looks to me like the guy knows exactly what he's doing. Id say he's done it a time or two. And I bet its done right.

[@GemmyHeart]

Main products: sealing gasket,gland packing,PTFE/graphite/asbestos products, ceramic fiber products, high temperature heat insulation and fireproof material. Free technical support (sealing, heat preservation, heat insulation, fire prevention problems) All products 1 piece can also be customized, 30 years of service experience, fast and safe shipping anywhere.

[@rk2045]

Those glands should be with lubricant or graphite impregnated. or with high temperature resistant grease.

[@ccmss45]

Great video. Thanks Guys

[@persianprinceG]

what is the metal thing that goes ontop of the last packing ?

[@renehernandezbenitez3529]

para mayor sellamiento en el presa estopas se coloca la unión de lada tira a 45 grados

[@9j4a2mz]

thank you ! this was helpful wrt lantern ring.

[@VannilaLotte]

hello i curios the tool you used to tighten the long bolt, you use drill and what??

[@dereck377]

Do you only have to stagger the stuffing packs 90 degrees from each other if there are 4 +? I noticed you did 180 degrees from each with 3

[@mysterion5312]

just make sure it will not make passage for leaking

[@jjyatuts3532]

thanks,a lot where is best place to buy good queilty gland packing in doha ?

[@黄翠玲-o8t]

we sell gland packings by good quality and best price in China!My email:[e-mail]

[@topsealing851]

Good idea!

[@feedyourfaith7392]

What is a stuffing box??

[@dixiegriffinjr.267]

Why not have the top 3 pieces of packing at 120 degree offset ?

[@suryakiran.ssk1972]

yeah why not? it makes symmetry

[@rohanmowatt3725]

Where is the best place to buy packing gland, in a walk in store?

[@黄翠玲-o8t]

we export gland packings!Email:[e-mail]

[@17SAIMPOINT]

THANKS ALOT, BUT YOUR SHOP IS TO CLEAN!!!!!!!!!!

[@darylsuarez5919]

whats tha color white seal? lantern way??

[@this_Is_n0_One]

Lantern ring... The lantern ring is used to distribute cooling water to all packing rings as well as keep the stuffing box clean of containments . Since the packing “grips” the shaft to limit leakage, even though the pump shaft is rotating and the packing is stationary, this can cause wear to the pump shaft.

[@berniejoyce5741]

How to replace seal in a motor on a shaft

[@tuhoangminh672]

rất thíc! xin cảm ơn các bạn..

[@kenhmaybomnuochanoi]

welcome to my channel water pump video

[@elleblommor9237]

You didn't do a stive cut this will leak horribly

[@MorapeliPakane]

❤❤❤❤❤

[@tinram745]

your packing ends are cut on the wrong angle.

[@dennyyang4508]

where do i buy yr pump?

[@maliksajid5157]

DENNY YANG hvvvvvvgv

[@fernandofilipinas1171]

👍👍

[@seanbirish]

It's the packing glands...

[@sunildhiman96]

not a prefect way to install gland, glands are not cutted @45 angle, second insert glands by gland follower only, not by rod as shown

[@thewarlordscalling6537]

They dont have 2 b @ 45°.bt your 2nd point is valid.

[@persianprinceG]

i handed my coursework in 5 months ago lol! But thank you

[@nikos27p]

The packing ring are poorly cut . The procedure is correct

[@Dwainpipe21]

They are not engineered studs just cheap nasty pieces of threaded bar! that's not good practice and what about using washers for christs sake you carn't just have a nut acting on a rough cast surface also why bother putting the shaft sleeve in when you fit the gland packing? it just makes it harder to fit, fit the gland packing first (firmly) put the sleeve on the shaft then fit the seal housing/stuffing box . when you tighten the gland it will compress the gland packing anyway.

[@arayamekuria2890]

He talks to his own he can't to explain by touching the parts we couldn't to identify the items he was explained very poorly.

[@darylsuarez5919]

whats the name , next to the packing gland , you didnt mention it (2 peaces oI= metal) pls dont make avideo iI= you dont know how to label it;s components