Make this BEAUTIFUL Walnut End Grain Cutting Board (Good Beginner Project)

[@daveconneronline]

Nice work!

[@susanhughes9139]

It really is beautiful!

[@patriot-maker]

Thanks!

[@ReedAllen162]

That looks very awesome. I really like the way that grain looks. But most beginners can’t afford that much Walnut . Heck even I can’t afford that much Walnut.😂

[@patriot-maker]

Ha! That’s probably true.

[@ericsyvertsen5880]

Great job, I have 2 pieces of walnut I've been holding on to for a while, maybe I'll borrow your design...LOL. At 11:37 where you're putting in the feet I see separations between some of the boards, next time, before you oil, fill that in with CA glue (brown), you won't even see them.

[@patriot-maker]

Good idea. Thanks!

[@wcroach1]

Looks great - I like the grain.

[@patriot-maker]

Thanks!

[@10001gunner]

Perfect, video......best iv seen, thx U...

[@patriot-maker]

Awesome! Thanks!

[@Ngry_W]

Nice job

[@patriot-maker]

Thanks!

[@leonardolunetta3222]

Belíssimo trabalho. Parabéns 👏👏!!! Ganhou mais um escrito. 😊

[@paulbeaver2918]

I see you’re running your boards through the planer and then right to a glue up. I have the same planer but I get terrible snipe. Even after ensuring the in feed and out feed tables are flush. How do you do it? Thanks YT BeavWod

[@patriot-maker]

I have a helical head on my planer that helps a lot. I did a video on it if you want to check it out. You may also want to try a planer sled. Hope that helps!

[@HearGear]

Great video... your DeWalt thickness planer, does it make snipe with that short wood ? or any snipe at all on any wood ? Thanks..

[@patriot-maker]

Thanks! It makes minimal snipe on short wood, but now that I switched to a helical head blade it’s nonexistent. I made a video about it if you want to go see it.

[@SkydiveDriver]

That board looks greet. Thank for your tips. By the way how do you handel your sales of cutting boards. Do sell out of state.

[@patriot-maker]

I’ve mostly sold to people I know. I don’t really ship but could if I needed to I suppose.

[@cjdrumstud]

Hey man that board looks awesome! I also really like the way your crosscut sled looks do you have plans for it? I have the same table saw haha

[@cjdrumstud]

Just noticed it's in the bio

[@patriot-maker]

Thanks! I’m glad you like it! You can get a discount on the plans if you join my email list! patriot-maker.ck.page/6ec995bca7

[@manuelkong10]

SO Beautiful ! WHERE DO YOU GET THE WALNUT....I looked up walnut on ebay and it's WAY more expensive than what you were paying I think

[@patriot-maker]

Thanks! Most of the time you have to get stuff like walnut from a local hardwood dealer. I’m sure there are some places that will ship, but I prefer to see it before I buy it anyway.

[@frogman5956]

How do you recommend getting all the dust off before oiling it? Mineral spirits, water, or just air compressor

[@patriot-maker]

I like to hit it real good with an air compressor then mineral spirits.

[@nevrynkinori3627]

It would be far better if it was backlit. Can it be used for hot pans?

[@patriot-maker]

I’m sure it could, but it would probably scorch it.

[@PapaBig91]

What size was the walnut board you used?

[@patriot-maker]

I’m sorry, I don’t remember.

[@bad26498]

Anyone watching DO NOT put end grain in your planer

[@patriot-maker]

Thanks for the tip.

[@jamesl7440]

Why would you use a jigsaw and THEN take it to the miter saw? Do those three seconds really make you more money? They make you look like an idiot.

[@patriot-maker]

I did it for safety reasons. My miter saw at the time couldn’t support a board that long.

[@robertsmith3518]

Jet's and garbage music is a cutting board ? . Try again

[@patriot-maker]

??

[@robertsmith3518]

Garbage starts at .011 seconds , I never made it past it, I tuned in to see a cutting board ,not a jet launching from an carrier plus the music sucks,it too starts at 11 seconds , maybe with a only 15 people commenting maybe I am alone maybe not . Next@@patriot-maker