Make your ER holder hydraulic and enjoy multiple benefits!

With the ETP ECOGRIP ER hydraulic sleeves you can easily turn
your standard ER collet holder into a high precision hydraulic holder. Thus you can easily enjoy all the positive benefits of hydraulic clamping such as easy handling and precision, at an
impressive competitive price level.
This enables more users to benefit from decrease tool wear and
increase productivity compared to using ER collet holders. With the use of the three axial screws an adjustability of the run-out is
achieved.

[@wrecking_havoc586]

These tools work great on our DMG NLX2500SY Lathe! This holder also helps increase tool life because it is more rigid than a ER collet. 🔥

[@etptransmission]

Thanks for the great feedback! / The ETP Team

[@MASwebvideos]

Great solution!

[@etptransmission]

Thanks!

[@jwoodshed1108]

How can I make that inside collet? Show us how to make it hydraulic.

[@josehernandez5671]

Very good solution specially for right angle heads.

[@etptransmission]

Thanks for the great feedback! / The ETP Team

[@markenriquez6937]

Probably the best use case.

[@hemantnikam6501]

What is cost saving wet buying new one

[@sidhivinayakindustries2637]

Can I get it in Pune India...

[@Saigonletterpress]

Very good , how to buy them in Viet Nam , I want to buy item for ER16 , ER 20 , ER25 . Thanks.

[@etptransmission]

Thank you Minato, for sales in Vietnam please contact our sales department at [e-mail] / The ETP Team

[@minatostamps134]

how many rpm was ETP ecogrip ER system banlanced ?

[@etptransmission]

After assembly of ETP ECOGRIP ER we reccommend a final individual balancing of the complete holder. Regards / The ETP Team

[@SuperYellowsubmarin]

Ok, but how cost effective versus buying a complete hydraulic holder ?

[@etptransmission]

30-50%. And re-use your excisiting basic holder!

[@guadalupemunoz9920]

Can I get them at Mexico? or even at USA Do works for ER40 ?

[@etptransmission]

Sizes available for ER40 -Yes!. For sales in Mexico, contact our US/Mexico sales office at [e-mail] Regards / The ETP Team

[@praveenrajbabu2790]

How to buy this in india

[@etptransmission]

To find your nearest representative in India please visit www.etp.se/en/about-etp/main-offices-power-transmission-representative Regards /The ETP team

[@DT-gm2zi]

Any Malaysian distributors?

[@etptransmission]

Of course, contact our customer service at [e-mail] for your local distributor. Regards / The ETP Team

[@cyber2526]

accepts reduction collets i asume?

[@etptransmission]

Correct, reduction collets can be used in any ETP holder!

[@cyber2526]

@@etptransmission awesome

[@cyber2526]

I’ll keep this in consideration when starting my own shop someday. I hope

[@rajashekarm.s.rajashekar6970]

Can I get contacts details in india.

[@etptransmission]

India sales rep available at: [e-mail] Regards / The ETP Team

[@justin_704]

3 thou TIR for a hydraulic holder when you can just use a normal holder? Why pay extra and get the same results?

[@etptransmission]

Hi Justin, the main purpose of this product is to eliminate runout in your existing ER collet holder and also in your machine’s spindle for drilling and reaming applications. Or for easier tool changes on live ER spindles. It is not meant to convert all ERs or replace hydraulic chucks. It gives you the ability to turn your ER collet chuck into an adjustable or steerable holder. Here a short summary of different tool clamping techniques at www.etp.se/en/content/the-evolution-of-toolholders

[@chodge9461]

Etp are swedish so that will represent 3 microns. If your tool is running out 3 thou, you need to change your holder and check your spindle