Massey Ferguson 65'ere - Veteran Pløjedag 2018 - Del 1

65'erens 60 års jubilæum til Veteran Pløjedag på Hinnedrupvej

[@marlonmendez8755]

Excelente tremendos tractores lo mejor de lo mejor 👍

[@brianmarshall1637]

Yes the mark two had the direct injection engine,better starting in cold weather.

[@claudioevoracharlon364]

Excelente Trartor mi padre compró uno en Enero 1959 lo tengo Original y trabajando esta

[@stevedelarre7494]

Just bought a MF65 Mk2 and stumbled upon this film. Pure tractor porn😄. Love it, thanks for posting

[@russellclement2058]

The MF 65 Mk 2 was the perfect tilling tractor I've spent thousands of hours on them,,

[@fredymanzano1075]

k hermosas makinas😊

[@danielmckay3458]

Had 65 Massey used a three bottom Massey blow with tripping bottom back up to relock great compensation

[@goias64henzovinicius95]

Bão demais .

[@donaldthomas5852]

65 Massey Ferguson a very good all round tractor. I have a IMT 539 it's the same as the TO35 Massey Ferguson they are good little tractors after adding some weight to them.

[@rajuseervi2896]

Good work

[@culmalachie]

Great variety of Little & Large - so many variations. Once again , it is such a pity that few seem to know how to set up a plow on a Ferguson - so simple - NO Tail wheel needed to adjust on a Plough. The Tandem seems to be doing better with that different plow though. Funny how some have so much front end wiight and others not at all, how track width varies so much etc ....Just shows you!! good to see. Cheers

[@rajuseervi2896]

Very nice

[@diegocampos1006]

In brazil we have a big lie of tires wide. Sorry my bad inglish. Good movie. Beautfull

[@arthurdewith7608]

At the time the mf65 was built no other tractor could match the hydraulics gear box or Perkins engine international had grinding gears and Smokey engines

[@denismcmanus8740]

The mf 65 was a tough work horse unbelievable grit

[@thodoris3790]

my fathers tractor .still working

[@garycase5666]

What about the transmission if it won't come out of reverse I have to open the transmission manually move the gear

[@user-vz7ld6lf8n]

You will have to unscrew the oil plug on the left side of the gear lever. Then you will see the large gear in the gearbox. You take an iron rod and press the clutch you try to bring it back to gear by leveling it vertically ... If the gear does not move, you must rotate the drive shaft through the gears and then try to equalize the gear.

[@seunheinlein336]

Do you people fill the rear tyres with water for more traction?

[@culmalachie]

Well if they knew how to set up the plough combo PROPERLY : ie how to use DRAFT /Draught Control and have the correct track width, plow weight / Number of furrows ( at least 3 ) and THREW AWAY he Wheel on the Plow - It's a FERGUSON, remember? - they SHOULDN't be using a depth control wheel. Heavens to goodness, I've used a 4-F 14" with full disc coulters and Auo-reset trips without using a depth control wheel.( not on a 650 - but had a 3-F on a148MP -no bother at all. Water( + Salt) was fine because it APPEARED to allow the tyres to Hug the ground better than Hi Air PRessure with wheel weights. Problem with UK MAsseys, they ALWAYS came as standard with Narrower t tyres and lower PRs compared with the opposition. 11/12.4 -28 or 32 or 36 whereas Ford & IH used 12/13.6-28 or 32 or 36 with 6 or maybe even 8PR whereasMF sold 4PR as standard. It was interesting to see the variation in wheel setups: Std 32" optional 36" and the Hi-clearance Front axles with 38" wheels:Just a pity that most only seemed to have 2-Fur ploughs: Put a SINGLE Furrow plow onto a big tractor and mamke a fool of it - more draft than weight transferred onto rear axle. Hope this helps

[@martinejoseph1644]

Tous des 65 mark II 56 cv sauf un , celui qui a la calandre et voiles de jante gris blanche 52 cv / mark I ... Vu carter moteur différent court demi longueur , tandis que les autres le carter moteur fait la longueur du bloc moteur avec les renforts avant arrière .....

[@culmalachie]

NIce video but: IF they knew how to set up the plough combo PROPERLY : ie how to use DRAFT /Draught Control ...... see detail in a reply below! Some people still have to learn a lot!

[@jordanterzic4834]

Very deep🤣🤣😂

[@denizozdemir1513]

Uu00

[@user-se3bn8vz9t]

ยากได้แต่ไม่มีตัง

[@serafettinyalcn5119]

Sizin yaptığımız aptallık manyaklık çocuk mu var karşımızda biraz akıllı olun biraz mantıklı olun ya

[@mojsijeaha2624]

Who are the strongest?🤣