They ruined that pin before they even got started.
@ES-ii7xn9 ай бұрын
It looks like the spindle is cracked
@brianvaughn929910 ай бұрын
Power steering or not that is going to be a monster to steer.
@larryssnova7610 ай бұрын
No new bushings just drive a new king pin in and your good when I’m done doing king pins you can move the knuckle with one finger !! Not one ten pound sledge!!!
@user-dh3md9cy6u8 ай бұрын
Всё он испортил
@jano2010 ай бұрын
Según mi experiencia está mal hecho el cambio de pasadores y bujes de muñones
@ANTiKillER14210 ай бұрын
Замена шкворней, без снятия цапфы, и без замены втулок, оригинально
@user-sx6cl8yq5j10 ай бұрын
А втулки, какие втулки не не было
@user-qb3gr6pt4n10 ай бұрын
Ага не опорный подшипник не поменяли не регулироаочные шайбы не поставили в таком случае можно было и старый палец оставить
@user-qb3gr6pt4n10 ай бұрын
Пальцу та в большинстве случаев вообще нечего не делается
@user-qb3gr6pt4n10 ай бұрын
Это как заменить тормозные диски а колодки старые поставить😂
@user-qs1gd5kh8o10 ай бұрын
Я за это и поставил дизлайк!!!!
@arthurpacis701010 ай бұрын
now that the new spindle is set, the driver will be complaining about a hard steering wheel.
@andresrattero96 ай бұрын
Ñ
@andresrattero96 ай бұрын
Ñ
@lloydprunier441510 ай бұрын
A late friend and mentor of mine lost an eye by hammering on a kingpin. People don't know how lucky they are sometimes!
@sidallen68510 ай бұрын
I knew a guy who hammered a u-joint and it fractured and imbedded in his eye, it blinded him.
@user-cm1qt8cg1i10 ай бұрын
Как же гидроусилитель руля будет визжать это ах😅😂 водитель будет в шоке
@1GR-FE10 ай бұрын
они про развёртку не слышали
@tarkia23910 ай бұрын
@@1GR-FE Развертка не на долго, я лично сам в натяг забиваю, ну естественно не так чтобы кувалдой, но чтобы монтажкой 50см повернуть можно было, и шкворня ходят года 2-3, а если развёртка то год и все , а то быстрее,все зависит конечно как честно ездить
@dannylinc624710 ай бұрын
There's a tool for that. Too tight, Toulouse
@ajones869910 ай бұрын
Rough enough is good enough.... Just grind off the damage😂
@joseantoniocastillarodriguez11 ай бұрын
Le tenía que echar un poco de aceite hidráulico y ya verían como entraría mejor
@juliancleary283110 ай бұрын
Good job its got powered steering ! ! ! ! swivel so tight ! ! ! !
@neilmchardy906110 ай бұрын
If you want it any rougher you’ll need to get someone else
@brianbidiuk312510 ай бұрын
Hilarious!
@airat36026 ай бұрын
Держите шкворню 1час в морозильники и он туда упадёт
@xxkingslayemxxgamer555310 ай бұрын
That should turn free by hand not have to beat it to move it
@larrysorenson478910 ай бұрын
Just beat it Beat it
@markpoehler745910 ай бұрын
A pigpen deserve new bushings I'm glad they aren't working on my stuff
@ernestimken696910 ай бұрын
Those men are truck mechanics, not auto mechanics.
@user-wy6zt9dt9p8 ай бұрын
Главное резаком погреть чтоб с кувалды вбить
@Yalguzag6810 ай бұрын
Без помощи кувалда не было бы техники на земле
@angelaguilar900110 ай бұрын
Mal trabajo tanto de instalación como de quien metio los bujes en el mgo y el eje
@j.onofre661310 ай бұрын
Y los bujes..?? No los cambiaron??
@jaimemonzon60439 ай бұрын
Por eso le lima el pasador,eso no se hace tiene que poner bujes nuevos,es como bañarse y no cambiarse calzoncillos.
@salomonreynoso73011 ай бұрын
No es correcta esa labor
@krzysztofstepien66679 ай бұрын
Nigdy nie dalbym wam zasrancy auta do naprawy
@mariomoreno995410 ай бұрын
China tales...quality!
@user-qv5gt5yp3c10 ай бұрын
Развёртка?Не,не слышал 😂
@alejandro61bo6 ай бұрын
Se usa una barra de bronce para no golpear el eje directo hierro con hierro y deformar el pasador
@justocastaneda37796 ай бұрын
Bueno, esa gente trabaja con lo que tiene, o sea mazo y cincel.
@error_glitch90710 ай бұрын
Rush & muld shall be cleaned to make sure there is no impurity material inside of grease
@aureliozacchi65376 ай бұрын
Que Horror, esse tipo de mão de obra desanima qualquer dono de caminhão.
@gnomoboy837110 ай бұрын
😮😮Браво зачем цапфу снимать райбировать втулки подберать шкворень ремонтный,проще взять и забить кувалдой и обсиратся за рулем😂😂😂😂
@georgerivera922010 ай бұрын
Long at the wheels on the jack. Must jacks are made in China but have steel wheels. I'm changing over.
@enriquemiras520111 ай бұрын
Una. Diosa. Hunika❤😂
@thomaswilliamfirby18010 ай бұрын
Anyone noticed the cracks in the casing ?
@DilipPradhan-nn8lz10 ай бұрын
Great engineering.....
@brarautorepairs9 ай бұрын
Torque specs, yes😂
@dontcallmemarty217711 ай бұрын
Never seen a torque wrench in ANY videos
@enriquemiras520111 ай бұрын
Diosa meka. Hunika❤
@garagenhuttv20957 ай бұрын
Làm xong lái xe khỏi đi tập tạ
@PedroGonzalez-sv1zi10 ай бұрын
Si se fija bien donde montaron el pasador tiene una fisura.........
@andryha1616110 ай бұрын
Втулки на следующий день скажут давай до свидания.и шкворень кстати тоже.привет капиталка
@lukaschabotier40976 ай бұрын
Oui ! ben ! bon courage !! voilà voilà
@screwyoutube.10 ай бұрын
Hacks
@antonjensen754611 ай бұрын
Uhh...this technique of yours...
@Day12310 ай бұрын
Good job
@sampsonsunny629810 ай бұрын
No self centring steering there.
@user-zh7yy9nu4u10 ай бұрын
Одно дело когда выбивают
@RONALDOBIKE260110 ай бұрын
👏🤝🥇🏆🙏🧑🔧
@arielmenga91479 ай бұрын
Que duro que entro la dirección va a hacer un cascote
@alwellygunawan99236 ай бұрын
Kamu tahu..palu nya spt punyaku 😅
@tompolomchak907910 ай бұрын
Thay used the wrong touch.
@dwmcever10 ай бұрын
NOPE.
@juanasanelli683110 ай бұрын
Menos mal que tiene dirección hidráulica
@juantrevino684911 ай бұрын
Like your videos. Talking like chipmunks is a plus….👍
@garazh-241010 ай бұрын
Азот в помощ😉и портеть шкворень не пришлосбы😏
@thelinh_tv76017 ай бұрын
dùng búa 🔨🔨🔨🛠đóng mà không kê dễ gây gãy hỏng trục