Nice looking hinges. However, method # 2 is a complete FUBAR. Do NOT install legs using Method #2. The legs wont lock, and screwing into the end grain of the legs is all but guaranteed to fail.
@jinavacana25104 жыл бұрын
Finally I found it thanks to you..!!!
@cathymcdougall98782 жыл бұрын
As far as I can tell, only method one actually locks the legs in place once the table is set up. Method 2, the legs would swing in if you picked it up to move it. Or am I not seeing this right?
@wrknmama2 жыл бұрын
This would be genius for a collapsible wall table.
@adamhenderson74845 жыл бұрын
Thank you for this, just what I am looking for
@laylamorgan40183 жыл бұрын
Yipeeeeee I've finally found the little locking thingy ma giggy I needed... Thank you 😊🎉🎉🎉🎉🎉🎉🎉🎉🎉
@gargipatilganjare33123 жыл бұрын
Where did you got this pls share the link
@laylamorgan40183 жыл бұрын
@@gargipatilganjare3312 go into the video discription he's added the amazon link
@goodwillmahto48432 жыл бұрын
Contact no send
@ibringthelastwords13584 жыл бұрын
Thanks! I need these on my project :)
@crazycrab8578 Жыл бұрын
just what I am looking for, to make a small table for me camper van :)
@adri07377 ай бұрын
is it possible to bend this outwards 180°?
@riakeinert3 жыл бұрын
Super helpful. Thanks.
@tengoats03 жыл бұрын
Great Video , I just ordered 4
@sabilfikri3 жыл бұрын
Exactly what I need. Much thanks!
@gargipatilganjare33123 жыл бұрын
Where to buy from
@Gardo09PR2 жыл бұрын
@@gargipatilganjare3312 Amazon
@sledtrash5 жыл бұрын
I'm looking for a similar hinge that has 2" offset built into it. I'm wanting a hinge that will work for a 2" slab drop leaf table. I want the leaf to flush out under the edge of the table. Do you have anything that would work for that?
@robira13133 жыл бұрын
Would those be good to hold up a 12-inch wide shelf?
@E3CB5 жыл бұрын
Awesome product!
@omarsh823 жыл бұрын
yes, was looking for this too
@SilverMiraii3 жыл бұрын
good solution
@saa-rahadams13104 жыл бұрын
Can this be used on a thick perspex?
@ayushjain79812 жыл бұрын
where can I order it from in India, need it asap????
@HeriPurwanto-ki4nz3 күн бұрын
Cek hrga bos. Psennya dmna
@jackduplechain75924 жыл бұрын
if I use these for bench press workbench would it be safe?
@codys75913 жыл бұрын
For weight lifting!!! Absolutely not I hope you are still alive and did not attempt this.
@jackduplechain75923 жыл бұрын
@@codys7591 ha I'm still here. didn't use them after all but almost did a few times.
@antoniolagahit76273 жыл бұрын
where can i have this?how much is this?
@vijaydwivedi31933 жыл бұрын
where can I get the CAD file for this
@fsmith31603 ай бұрын
These are NOT 90 degree locking hinges. While they open and lock at 90 degrees, when you closed them the will not lock in the closed position. The supplier said "just raise the hinge on a block". I tried adding a 1/2" block and that did not make it lock. I then went to a 1" block and that didn't work either. Even after adding a block height of 1.5", the hinge would not lock down. It appears that the hinge may have to get closed to a 115 degrees or more before it will lock in the closed position. That being the case I would have to add upwards of 2.5" of block to raise the hinge enough to make it fold and lock. In turn, it your looking to get a flat leg fold, that does NOT work. When shown both the video and raise block pic, the response from the supplier was "Just send them back". TOTAL WASTE OF TIME WOR THESE HINGES.
@akshaybhau51814 жыл бұрын
Please tell me name of this hinge👈
@nowthenad32864 жыл бұрын
Why would anyone want to make a table with legs that are locked in the folded position but not when the table are erected?
@junebarcega59804 жыл бұрын
anyone knows how much weight it can support?
@jaschaschaub6763 жыл бұрын
I'm concerned about this as well.. Not shure if I should use those for a ramp
@codys75913 жыл бұрын
Site claims 500Lbs...however it is a bracket and I assume this is based off a vertical load factor
@karaleigh_eva3 жыл бұрын
Does anybody know how strong these are? Could they work as a bracket to support a shelf?
@sentradynamics88893 жыл бұрын
These are strong but really too short for a shelf. Look for folding shelf brackets 😁
@sz41794 ай бұрын
Amazon ad says 500# but thats downward pressure. Not sure if suitable for a shelf.
@vishalsahu27883 жыл бұрын
Ye clip kha milege
@thesultanmerchant3 жыл бұрын
THE QUALITY OF HING SAME AS SHOWN IN VIDEO IS I RECEIVED IS VERY BAD AND NOT VERY FRIENDLY USER. FIXING OF SCREWS AND OPERATING HINGES IS VERY CUMBERSOME. I INSTALL 4 HINGES IN U SHAPE U SHAPE OF MY FOLDING TABLE AND CANNOT OPERATE ALL 4 HINGES SIMULTANEOUSLY. AND HAD DIFFICULTLY IN INSTALLING SCREWS BECAUSE THE LOCATION OF SCREW HOLES ARE NOT PROVIDED AT CONVENIENT LOCATION. OVER ALL DESIGN OF HINGE REQUIRE PROPER DESIGNING AND GOOD FINISHING. CAN YOU MAKE VIDEO SHOWING INSTALLING 4 HINES ON U SHAPE LEG AND SHOW OPERATING METHOD.?
@vijaydwivedi31933 жыл бұрын
your website is not working
@RajeshKumar-tm1jw5 жыл бұрын
Name and prise of this bracket in india ?
@fredmccrimmon743 жыл бұрын
Amazon
@ohcrapitsmrG5 жыл бұрын
lock in one direction
@ercanimer4864 Жыл бұрын
He is using pliers to make the product seem stiff :D
@dynoman7 Жыл бұрын
(i think there is something wrong with the person in this video)
@tomekapompey5633 жыл бұрын
My adventure with woodworking started with Woodglut.