Who ever watches this: Never do it this way. do it properly and switch the backplate (it's around 30 bucks for the plate and some for gasket maker). Besides there is a little drain tunnel under backplate which helps draining the V-room from water and leads under the engine. So if you skip changing the plate and do only the rear main seal, your engine might still be leaking oil cause it will leak through that tunnel if the old gasket went bad under neath.
@JodyBaxmeyerPresents Жыл бұрын
I was just going to comment the same thing. This is how you repair: if you WANT YOUR CAR TO START LEAKING again in months. If that plate (crankshaft seal retainer) is not removed and replaced using gasket sealer, that new installed engine seal will 'shift' and in some cases will cause an even WORSE leak, not to mention the job is worthless and has to be done again, with a new engine seal and retainer clip.
@sassanettekal14906 жыл бұрын
This is a hack job. It is a must to replace the backing plate where the seal is installed on and you don't use tools to remove the seal because if you damage the crank shaft you are screwed. There is a special too to install the new seal at worse you use a piece wood and a light hammer to push the seal in place. gently
@Musclman78TA18 ай бұрын
Thank you very much for the advice it’s more like the GM backing plate that you have to replace every time
@rl48895 жыл бұрын
Too bad you didnt show disconnecting the cooler lines lol. Really needed to know that part. Great video though
@youtoobe1693 жыл бұрын
Why would you go through all that trouble just to take shortcuts and potentially mess things up?
@jonathanandivannacobb27793 жыл бұрын
Good video, thanks for the details.
@ozelot2509 жыл бұрын
Did you need to drain engine oil and transmission fluid before removal?
@LynxStarAuto8 жыл бұрын
Engine does not need to be drained. Transmission will lose some oil due to the cooler lines being disconnected. Otherwise, no other point on the trans itself will leak fluid.
@tonychavez2083 Жыл бұрын
the nice thing is that you dont have to drop the exhaust to remove trans..
@anibalnikov475 жыл бұрын
is this a 722.6 transmission?
@teespeed5 жыл бұрын
Total hack job.. Back yard mechanic. There's a reason he only shows part of the video. That seal needs the entire flange with it, you just scratched the ****out of that crank removing it the careless way
@hunterharison3 жыл бұрын
exactly ...KZbin butcher video of how not to...lol
@Motorsportsgeek7 жыл бұрын
Im about to attemp this on my 2008 c300...4matic. It relativly looks the same as in this video other then the driveshaft going to the front transfer case, is it that easy? Also my main seal doesnt come as a single round gasket but a whole timing cover tip assembly, is it as simple as changing a front timing cover ?
@youtoobe1693 жыл бұрын
OMG I just noticed they list the shop name. Good advice to never go there LOL
@HamidRHariri10 ай бұрын
Why didn't he replace the plate rear main seal goes on? It should have been replaced with a new one and sealed using a gasket maker.
@raiden40044 жыл бұрын
How many hours would u say it takes to do this?
@k0712s7 жыл бұрын
What is the white ring inside the new seal, he is tapping on it to seast the seal in? I didn't see that on the new or the old seal.
@A.Musa768 жыл бұрын
I'm getting ready to do mine on my CLK500. Is there any stretch bolts I need to replace? If so which bolts are they? my last question is when putting the sealant around the new rear main seal plate. How long do you need to wait before putting the transmission back in? I heard there is a curing dry time for the sealant from other MB forums but no one specified how long and why is there a curing time. Can you please explain this.
@miketshotwell3 жыл бұрын
The flexplate bolts are torque to yield "stretch" bolts that need to be replaced
@mustnoor9 жыл бұрын
Good video thank you
@Hmmm3134 жыл бұрын
what about the rear plate???? why doing half job???
@hunterharison3 жыл бұрын
forget that ... does not matter anymore ... " this is a perfect way to scratch up the crank while removing the old rear main seal video " lol
@davejohnson38602 жыл бұрын
@2:26 sould'nt that be a rubber mallet?
@georgeanddaddecker7563 Жыл бұрын
Hack!
@shwndh9 жыл бұрын
So, removing the whole plate is not necessary? Nice!
@LynxStarAuto8 жыл бұрын
The plate should always be replaced with the seal. Trust me, its for piece of mind. I have had them return with small leaks 2-3 months later. Replacing the plate along with the seal results in the best quality repair for the customer for not much more money. I also like to upsell the transmission pump seal and drain/refill the torque converter.
@zeomarmob6 жыл бұрын
Not to reseal the cover and not changing the transmission seals is a waste of chance.. also you don’t know if the cover is already leaking. Plus it’s a lot easier to replace the seal with cover off.
@Elchullaquiteno17 жыл бұрын
does anybody know how much is just labor $$$$$$
@teespeed5 жыл бұрын
Ask the person who might do the repair, they would know best... Not us. All we know is how much labor it takes us is to watch this video