Great job thanks.....the check valves are cupped though make sure the green/blue strip is up.
@605BOLT Жыл бұрын
Yes. I didn't see any cup on mine but def that's the way to do it. I will pin your comment in case anyone misses that. Thanks for the kind words!
@insanevtec9200 Жыл бұрын
Great video! Will help out with my carb rebuild this weekend! Thank you !
@605BOLT Жыл бұрын
My pleasure. Remember to stay hydrated! 🍻
@neppy511 ай бұрын
@605BOLT thanks for this video! you explained things so clearly and great close ups/camera angles and everything, easily the best rebuild/pop off video i’ve come across and i’ve been using it as a guide to rebuild my dual carbs on an xlt 800 basically identical setup to yours i’ve got this baffling issue where i can’t build pressure above 40psi during the pop off test, i have the same tester and it goes past 100psi with just the hoses blocked off up to the carb inlet, don’t see any signs of a leak in the needle/seat, no bubbling, really at a loss as to why it won’t build up higher pressure
@605BOLT11 ай бұрын
I have another video coming out later where I needed to adjust these settings. It had a bog off idle that I couldn't fix. I got a bigger needle and seat and pulled pop off back to 45 and it cleared right up. Assuming it will help you too. Thanks for the kind words. Could be not building pop off because the needle and seat are wore out.
@neppy511 ай бұрын
@@605BOLT thanks! i’m subscribed and looking forward to that video. My needle and seat is actually brand new oem mikuni, and i used the oem rebuild kit as well. Decided to think out of the box a bit and found that air is actually leaking from the other side!! (pump side?), so weird, i tightened up the screws but it’s still leaking, made a short video of it kzbin.info/www/bejne/r4qqc5qNbdqZpM0si=xZu5CcGbfQNIXnoN the carbs are from 20 year old machine, wondering if they’re still fit for service
@605BOLT11 ай бұрын
@@neppy5 I'll check it out.
@alfredorodriguezjr86604 ай бұрын
Hello my guy..... Greatly appreciate your videos I might be needing some of this information in the near future
@605BOLT4 ай бұрын
Thank you for the kind words. Ultimately I hope you don't need it!
@alfredorodriguezjr86604 ай бұрын
@@605BOLT you see the thing is I just picked up two free jet skis 1996 Kawasaki one of them is a 900 the other one is 750... They've been sitting for a few years... I'm going to start working on them seeing if they run
@605BOLT4 ай бұрын
Right on. Sounds like a score!
@richardanderson8588 Жыл бұрын
Great video bud/ Your hose to the Accelerator pump has a check valve inside it. Do not throw away the hose. look inside for jet style check valve. Reinstall it! I set my Pop off at 35 psi
@605BOLT Жыл бұрын
I just went and checked the hoses. I actually kept them. No check valve😬. I wonder what is going on there?
@kyleroman9326 Жыл бұрын
@@605BOLTI just checked my 98 gsx l (5625) none either
@605BOLT Жыл бұрын
@@kyleroman9326 idk then. 🤷♂️ I'm glad you commented though because I feel like people will be curious
@AchikSarih4 ай бұрын
Merci beaucoup ❤❤❤❤❤❤❤
@605BOLT4 ай бұрын
You're welcome.
@EEI605 Жыл бұрын
Nice. Liked the video
@605BOLT Жыл бұрын
That was a crispy pop off though.
@vitaminp5793 ай бұрын
Just found this...Thanks. it's helping me out big...One question...If you kept the same spring and needle, how did the pop off get to 80 psi? What changed? Thanks ..
@605BOLT3 ай бұрын
Idk. That's why in the next video I ended up changing some pieces around per sbt. It ran on plane ok but wouldn't hole shot well.
@guerosern Жыл бұрын
Cool 😎
@605BOLT Жыл бұрын
🙏
@omerbbM55 ай бұрын
13:25 The gasket and plastic sheet in the picture on amazon is not the same as yours
@605BOLT5 ай бұрын
True. But it's just a picture. As long as you get the Mikuni kit you're good.
@nickmocilan9067 Жыл бұрын
Do I have to adjust the idles and lows and highs or if they look right then don’t even touch them
@605BOLT Жыл бұрын
If possible, don't mess with them. If it runs, leave it.
@605BOLT Жыл бұрын
The settings are highly dependent on where you live and any mods or not.
@nickmocilan9067 Жыл бұрын
@@605BOLTI got my needle and seat out but then that the 2 screws to get to the jets it looks like the last people who did it stripped them pretty bad any ideas how to get them out?
@605BOLT Жыл бұрын
@@nickmocilan9067 shoot that's gonna be tough. Could try cutting a little slit in the screw to make it a flathead. Might work. Otherwise just leave it maybe. That's from somebody not using those Japanese screw drivers I bet.
@nickmocilan9067 Жыл бұрын
@@605BOLTI ended up drilling the head off real risky but worked out thanks for the help though