Thank you SO much for this. It worked ! The fet was just displaced, re-soldering it was all that was needed. This little grinder has been so useful to me and as they only come to lidl occasionally, it means I can wait now instead of spending four times as much on one that is not as good. Many thanks. (I soldered a 30mm copper strip onto the pad to disperse the heat. Seems to work. )
@zana35873 жыл бұрын
thank you
@zenonaspetkinis947911 ай бұрын
@@zana3587 Žinai, vaikine, negaliu atsistebėti Tavo žiniomis ir gabumais....turbūt, nėra pasaulyje įrangos, kurios Tu negalėtum pataisyti....sėkmės... linkėjimai iš Lietuvos....
@boozramos1402 Жыл бұрын
I was very doubtful at first but then I understood you, very good job !congratulations!
@fildancingio982 жыл бұрын
you know your job well so you have brilliant ideas! Compliments
@rolandocorrea12044 жыл бұрын
Mi querido dahen ,cuando vayas adesoldar piezas en una placa electrónica usa pasta para soldar es más efectiva. saludos desde República Dominicana
@zana35874 жыл бұрын
Gracias señor, mis saludos a Dominica
@ضياءابراهيمحمد Жыл бұрын
احسنت دائما مبدع اخي العزيز زانا هل استبدلت الموسفت ام بقيته على حاله؟وعندنا في بغداد نفس المواصفات موجود
@ضياءابراهيمحمد Жыл бұрын
تغير الموسفت لأجل ان يبرد؟
@villalbar4 жыл бұрын
Tank you vert Munch!!!! Now my minidrill work better: it works !!!!😁😁🤙🤙🤩🤩🤩
@zana35874 жыл бұрын
Thank you sir, very good
@Holanduzo Жыл бұрын
the screwed rod has just gone for use, where can I get a replacement?
@mtn_sivliu4 жыл бұрын
There are many models of the same Parkside drill tool, mine was the version with two M7 Diodes in Parallel connection and a CSD30N70 N-Channel Power Mosfet. First if the tool does not work,check the voltage of the battery,must be around 12v fully charged, check the pins of the drill if they make contact on the battery or not. Take off the PCB, inspect the two M7 Diodes (mine were a little out of place,probably they got hot,and got desoldered, so i measured them ,one was dead short,the other was fine at 0.6v) the M7 diodes are smd version of the 1n4007 1000v 1A, so i replaced both of them since i had already some 1n4007, but if you can you could also use a Schotty diode like SK56-DIO 60V If:5A,the schotty diodes are optional only if you want your drill to last a bit longer. after replacing the diodes,insert the battery ,then if the drill works immediately without powering it on after inserting the battery,this means the mosfet is probably dead. Desolder the mosfet. Measure the Source (right most pin, pin3) and the Drain( middle pin , or pin 2, or the cooling tab)> if the value is close to 0 OHM( mine was 1.2ohm) then the mosfet is dead,replace it with any 30v VDSS , ID bigger or equal to 55A and preferably low RDSon smaller than 9mOHM. I had a AUIRFR3504, rated 40VDS but works ok i guess.
@zana35874 жыл бұрын
thank you sir for your info
@ianvicedomini26485 жыл бұрын
Pretty damn good job there my friend
@zana35875 жыл бұрын
Thank you my friend i hope it's useful for you
@chakibebrahim35484 жыл бұрын
Cleaning and lubricating the Parkside pass 3.6 b2 gearbox thanks
@zana35874 жыл бұрын
ok
@ohranitel3 жыл бұрын
HI.Great video.Mine has burned the small chip and i can't read what it is.Can you help me? i need the label on the small 8 pin chip.
@Tefery Жыл бұрын
Thanks man
@pippoduro735 жыл бұрын
ottimo lavoro bravo
@zana35875 жыл бұрын
Grazie Signore
@940azh7 Жыл бұрын
Peace be upon you I have a question is Parkside company good or not
@mattiaatzeni95032 жыл бұрын
Hello, I’m Lussorio, an italian hobbist, not a tecnician I have a Parkside PFBS L A1 mini drill, the one with the removable battery. It doesn’t work anymore but I’d like to repair it. It seems that this tool is manifactured by Grizzly tools company. The problem is that the tool won’t turn on and I don’t really understand the reason why. I opened it and nothing appears. So I tested the motor first and it works fine. I thought the problem was on the control board marked AO5316. It has a round red switch to turn the tool on and off. On the board there are an IC controller marked S69-2LF (think from Delta Electronics but not sure of this), a switch mosfet marked CSD30N70, two M7 diodes and a toroid ferrite ring, as principal parts. First I replace the two M7 diodes whenever they seemed in working order and the tool won’t turn, then I replace the CSD30N70 mosfet (unfoundable yet) with a DD3906 with similar features and the tool still won’t work. I also replace the S69-2LF IC (also unfoundable) with a MAX4391 with same features (read it on the web but not sure of this). Unfortunately, no one of those paths solved the problem and the tool is still mute and won’t work. I need help and I ask you if you can do that telling me where should be the problem. Otherwise I ask you if you can inform me about a place, a site where to buy the complete control board. Any help is welcome. Thanks. Photografies of the tool’s control board (switch and IC unmounted), the housing’s drill and the battery are attached. Please let me know about. Address mail: zopdur20@yahoo.it
@zana35872 жыл бұрын
sorry sir no idea
@74871709q4 жыл бұрын
Eres un genio grande ,gracias por compartir maestro.
@zana35874 жыл бұрын
gracias Señor
@joseponcedeleon5196 Жыл бұрын
PREND UN CHALUMEAU
@madhukeshnp2 жыл бұрын
Use flux to ease the process of removing the mosfet. Also use an hot air station for this kind of job. It makes things easier. By using flux the solder melts and flows easily.
@zana35872 жыл бұрын
thank you
@jusb10667 жыл бұрын
very good fix Zana, only problem is, charger may take many days, they take 10hours just to charge the 9v square battery, the lion is much larger. much better than throwing away, i cannot believe the mosfet melts from the board! bad design
@zana35877 жыл бұрын
thank you man - i know the charger very slow but i don't have another one - yes bad design
@jusb10667 жыл бұрын
do you buy broken tools because you enjoy sometimes repairing them? i have often bought rusty hand tools for the fun, an old plane was fun to restore to shiny and sharp blade, handles were split, chrome was bad, it looks very nice now, and works great, i enjoyed doing it
@zana35877 жыл бұрын
I like repairing stuff - yes I bought all to fix it - good job I love RC and rusty hand tools
@zana35877 жыл бұрын
I have old RC engine but its not work - i think need more parts to work
@jusb10667 жыл бұрын
maybe use a $1 dollar dc-dc boost converter and an old phone charger to charge the device? you can accurately set the converter to match the near fully charged voltgage on the lipo, maybe use a resistor to limit max current for empty battery, even some resistance wire on a metal case, about 1 ohm should match it well
@valterf.52284 жыл бұрын
You did a great job but you need a new soldering :-)
@zana35874 жыл бұрын
thank you sir
@uwew61266 жыл бұрын
Testing not this Maschine on Factory ? Sorry that's Pfusch ! Great Video Thanks. My Maschine go 2 sec and than out, and the next on/off Button go 2 sec and then out.
@zana35876 жыл бұрын
This seems to have not been tested at the factory. Test the mosfet
@roterStern19174 жыл бұрын
Finest german english skills.
@user-fafa7204 жыл бұрын
WOW....This is so good drill !!😍😍😍❤❤❤
@zana35874 жыл бұрын
Thank you
@anilbasher87603 жыл бұрын
Nice bro but from where do you find these old tools
@anilbasher87603 жыл бұрын
But I also need some of these machines
@zana35873 жыл бұрын
Don't you have a Friday market in your country?
@zana35873 жыл бұрын
in old market
@canindelopes91384 жыл бұрын
O senhor é muito criativo.
@zana35874 жыл бұрын
obrigado senhor
@ThePawelekPawelek2 жыл бұрын
Using hot glue to fix hot transistor in place?
@zana35872 жыл бұрын
no sir
@baltikumer894 жыл бұрын
Thanks, very helpful.
@zana35874 жыл бұрын
thank you sir
@DashCamSerbia Жыл бұрын
How can I remove the gold colored shaft from the motor shaft?
@DashCamSerbia Жыл бұрын
I need to replace the motor, but how do I detach the shaft from it?
@antenisca13 жыл бұрын
A good job, but 2 things: terrible welds and use a little shrinkable sheath ... ;-)
@zana35873 жыл бұрын
thank you sir
@electroniquepassion6 жыл бұрын
👍👍👍👍
@zana35873 жыл бұрын
thank you
@IRILPRL6 жыл бұрын
Dahen Zana describe muy bien cual es el problema de esta herramiente y me parece interesante su aportación para mejorar la refrigeración del mosfet
@zana35876 жыл бұрын
Yes I try to reduce its temperature by fan
@zagranichnaja_zhizn6 жыл бұрын
thanks! very interesting video!
@zana35876 жыл бұрын
Welcome
@virgisvanagelis32612 жыл бұрын
super👍
@KarwanShkur4 жыл бұрын
زور جوانه ئةيشةكانت زوريش بةروفيشناليه باور ناكةم كورد بيت
@zana35874 жыл бұрын
بةريزى
@AdelyDeni4 жыл бұрын
Next time please use flux it will be so much easier.
@zana35874 жыл бұрын
Ok
@IRILPRL6 жыл бұрын
Tengo varias herramientas Parkside pero esta me ha decepcionado. El producto es de muy baja calidad. Sin someterlo a un gran esfuerzo de poca duración, el mosfet se ha desoldado en dos ocasiones. El diseño es incorrecto, no han considerado el excesivo calentamiento y deberían haber mejorado mucho la refrigeración Por otra parte el cojinete del eje soporte del mandril no ajusta bien y desde nuevo, la máquina vibra mucho a determinadas revoluciones El cargador es malísimo. Para evitar nuevas decepciones, he comprado un Dremel 4000 con el que estoy muy satisfecho
@zana35876 жыл бұрын
Yes, your saying is true. It's not good. I also bought a lot of it. But I bought the used and broken to fix it
@rolandboyle25335 жыл бұрын
Mosfet OK. Switch on lights up. Turn up speed lights go out. Motor does not run.
@zana35875 жыл бұрын
Take out the DC motor and battery and check them with together with wire
@SblackangelC5 жыл бұрын
I have the same fault like Roland. I took out the motor and connected to battery and it doesn't run mosfet is ok, motor with 5volts runs, battery voltage is normal. I can't for the life of me understand what's wrong.
@rogertyler32373 жыл бұрын
Why Don't You Just Use A 9 Volt Power Supply?
@neozalman5 жыл бұрын
mosfet solder back is easy
@zana35875 жыл бұрын
Yes
@garyt11195 жыл бұрын
Save the planet dude. Repair recycle etc (LoL)
@sirwann833 жыл бұрын
دەست خۆش 🙏🙏🙏
@zana35873 жыл бұрын
بەریزی
@ardeleanist4 жыл бұрын
How to change the bearing ?
@zana35874 жыл бұрын
i don't know . sorry for late
@جنوبيالهواء-د3ي4 жыл бұрын
ممتاز جدا
@zana35874 жыл бұрын
اشكرك سيدى و اسف فى التاخير فى الرد
@جنوبيالهواء-د3ي4 жыл бұрын
@@zana3587 شكرا لك صديقي
@mike-jo6lb4 жыл бұрын
Zana how much you buy the all machine..
@zana35874 жыл бұрын
1$ to 5$
@xinixxagnix2015 жыл бұрын
clean tip is half the work, thnx anyway.
@zana35875 жыл бұрын
Thank you
@DashCamSerbia3 жыл бұрын
Not a good idea. Freestanding MOSFET is a bad idea. Airflow alone is not sufficient to cool it. It needs a heatsink. They way it was from factory, the circuit board is used as a heatsink, but not enough copper plane.
@zana35873 жыл бұрын
This is just an idea
@عليالرسام-ي7ط4 жыл бұрын
سوءال اخي ليش البارك سايد مشاكل في الجهاز و البطاريه
@zana35874 жыл бұрын
لا ادرى !!
@geoffankrett70124 жыл бұрын
You want to find a good soldering iron
@zana35874 жыл бұрын
thank you for your info
@practicallab4 жыл бұрын
Good
@zana35874 жыл бұрын
Thank you sit
@practicallab4 жыл бұрын
@@zana3587 welcome sir plz sub my channel
@mareoman15593 жыл бұрын
احسنت
@zana35873 жыл бұрын
اشكرك اخى العزيز
@bassambarakat91906 жыл бұрын
No I did not test it!!
@zana35876 жыл бұрын
+bassam barakat Check MOSFET as I did in the video by the way it's mosfet not transistor . if you have any question i am ready
@bassambarakat91906 жыл бұрын
Thanks, I will buy the gadget (mulimeter) to check it and will let you know the result also will buy the mosfet just in case.