Mini T 2.0 aluminum upgrades with 0808 motor 5300kv and Mamba Micro X update

Heres an update on my Mini T 2.0 that i just finished pretty much fully upgrading. I installed: Hot Racing aluminum front knuckles and Losi aluminum rear camber caster blocks, GPM aluminum front bulkhead, GPM aluminum front camber block, MIP CVDS, rear hot racing aluminum shock, front losi aluminum shocks, castle 0808 motor 5300kv, hackfib carbon fiber front and rear shock towers, mamba micro X esc for 3s power, losi aluminum front pivot block, losi aluminum bell crank and drag link, losi rear aluminum pivot blocks

[@ClevelandRips]

Just got my Mini-T 2.0 and love it! Great vid! New SUBSCRIBER here!

[@sandman503]

Mip sticker placement is on point homie

[@matthorseman2008]

I also recommend dailing down the punch setting with the esc programmer because my latrax Teton 4x4 with the same brushless setup eats diffs & craps glitter on every run

[@reitplace4765]

Nice upgrades!! new sub.. good content... Thanks for sharing.

[@benscootin4329]

I have those hot racing shocks and that motor on my latrax teton, I love them.

[@mgscheue]

Happy to know I'm not the only one who had a difficult time filling the Losi shocks. If there's a trick to it, I'd like to know.

[@therealteja]

Yeah. I’m got a fresh set of all 4 from a friend and idk they are setup really nice from the factory. Incredibly smooth and excellent damping and spring rate. I tried my best to replicate that with the hot racing shocks but i couldn’t. Maybe with more experience maybe but Yeah if i ever find a trick to filling the losi shocks then I’ll make a video

[@OpLapDancePikachu69]

LETS GO

[@jeremymarano4866]

Sweet, I was thinking of switching out the brushless with the same castle setup you have if it would make a real improvement. Waiting for speed runs thanks for the video

[@therealteja]

Absolutely monster improvement

[@therealteja]

I have the stock gearing from the original brushless and i run mostly 3s now. Incredibly bullet proof. I run back fo back to back to back 3s and no heat issues just at opersting temp. Now I usually drive in the afternoon when its a coolish California temp to be outside. Id be more cautious if I was driving in the 90 degree heat like maybe 5 minute break in between packs

[@onkelleuchte2616]

@@therealteja I use the 0808 4100KV with 3S in my Losi Mini B It is very nice but i have many issues with the orginal differntial ballbearings and the ballbearings on the rear tires. How often you repair the diff ?

[@therealteja]

@@onkelleuchte2616 so you diff i dont run the stock diff anymore but id be sure to check your slippper pad wesr and clutch tightness to start with.

[@therealteja]

@@onkelleuchte2616 i currently run hot racing spool diff in my mini t as i have its suspension and chassis tuned more for off road chassis balance. The mip diff. I had it setup really well for a short bit of time but i guess i didnt do something correctly and the diff failed. I was super careful with my replacement but it also failed but hot racing no issue after i fixed slipper clutch by replacing slipper pads

[@sTuPiDiScOoL_]

Nice man how has it held up with this system in there and also what are these like maintenance and reliability wise mate pretty much nothing or they bit more complicated mate

[@mojojoji5493]

You need stiffer shock fluid to get the stock shocks to bounce normally. stock it’s set very soft

[@mojojoji5493]

Glad you saw this

[@aguyinnc2865]

Do you have a part number for the wider esc/radio tray? Having trouble finding it. Thanks!

[@therealteja]

eaglesviewaerial.com/?page_id=283#!/Mini-T-2-0-Aluminum-Electronics-Tray-Battery-Hold-Down/p/430885458/category=75551068

[@kennyperson6844]

I have the mip diff and with this same setup and it sucks you have to lock the diff or it will slip you better off with the hot racing diff

[@Letsgetitdonesparky]

I just got my miniT2.0 is that on Amazon where you’re getting all your upgrades ?

[@therealteja]

Ebay, local hobby shops, theres a lot of after market support for the mini t

[@billyjoe6314]

Cool truck! What’s the motor mount? Max size motor it can take? Thx!

[@therealteja]

I run the hot racing motor mount which is basically for stock size motor. The mamba 0808 fits it. U could put a “big block” motor mount but u have to consider the rest of the chassis balance. A bigger motor will rear bias the weight. In later vids i show weights i added below the servo and battery tray and hot racing brass front pivot block. This chassis the fun comes from tuning it to handle big power

[@lol123321123321]

You had a stock mini T brushless 6000kv before? Or the brushed version? The brushless is pretty quick. I didn't think it would be worth upgrading over stock. I don't really like the built in speed controller though. Mine failed and they're $80 plus shipping...

[@therealteja]

I had brushless

[@therealteja]

I upgraded it because i wanted 3s

[@chadthunderd1ck734]

Did the losi shocks come pre filled with oil?

[@therealteja]

The losi ones do but they feel flat and very little. The Hot racing ones do not come with oil. I run 32 weight in the rears with softer losi springs instead of the blue HR springs because those are too stiff. The Hr shocks are super super super easy to fill with oil

[@chadthunderd1ck734]

@@therealteja thanks

[@charlieknight9988]

Hello I have this combo sitting here what all is needed to install this and how do you have the esc like that for the battery?

[@therealteja]

Do you mean the esc tray?

[@therealteja]

eaglesviewaerial.com/?page_id=283#!/Losi-Mini-T-2-0/c/75551068 this where i got the esc tray from

[@matthorseman2008]

I'd love to know the top speed and how controllable it is

[@therealteja]

Very controllable with weights even on 3s. This video is before i did a lot more balancing and suspension tuning.

[@matthewhowell4065]

Is it faster than the brushless that comes on some of them?

[@Rektumresizer]

Depending on the kv motor you get with the kit it can be.

[@nashgkrish5683]

Hey man you have a fan mount for the motor. Do you have the STL file for it? Cheers

[@therealteja]

I don’t remember

[@nashgkrish5683]

@@therealteja no worries. Yeah looks good and I have a fan. Want to mount it.

[@marcosmendez1029]

Carbon towers?

[@therealteja]

Yeee

[@alihessami9102]

Wow, great job! Btw what is the type of gearbox you are using with that Mamba Motor?

[@therealteja]

In this video stock gearbox. I think i had some mip stuff in here. Currently mysetup is an mip steel input shaft (attaches spur gear) and a hot racing spool differential. Stock diff at any time is one wheel drive because its an open diff. Feel free to check out my other upgrade vids and running vids! Feedback is always great

[@mikekiss5757]

What battery are u using

[@therealteja]

Ovonic fpv 650mah 80c 3s and max amps 100c 860 mah 2s

[@mikekiss5757]

Ty

[@fonzy.3572]

Hey bud how can I use the stock Receiver?

[@therealteja]

You can use the stock receiver. In later videos i am using a dumbrc radio with x6fg receiver that has a built in gyro. I have added weights and keep the gyro running at 15% so i can actually put power down in corners with 3s

[@therealteja]

The dumbo radio and receiver is about $40

[@206beastman]

With those bald tires I bet you can't go anywhere wtf

[@ryansantiago941]

Hack “Fiber” front shock tower😂😂😂