Thanks for the video, I could not figure out how the motor was held in place until watching your video. Really strange retention method they chose. I wonder why some screws would not have been sufficient... The motor in mine came loose which pulled on the wires and eventually shorted them. I am going to attempt to solder them back in place and put everything back together securely and hope for the best. Thanks again!
@GoBrogarage2 жыл бұрын
I am glad that my video helped you in some way) because I tried for this) I was also surprised by the engine mounting system on this machine, it seems to be reliable, but the glue ceases to hold over time.
@muhammadshareefali4659 Жыл бұрын
Hi..take a another video to how to cable soldiering & desoldring what have problem in pcb card, in repair some time speed very fastly why how to slove the problem.... I'm repair but some time this problem not understand... Pls clarify... Than q.... For this video.... 👍
@paulwalton89822 жыл бұрын
Wow, fantastic video. very clear demonstration on how to repair. Your a genius 🙂
@GoBrogarage2 жыл бұрын
Thanks 🤩
@СергейИванович-е8с2 жыл бұрын
Надо было дальше разобрать
@GoBrogarage2 жыл бұрын
А куда ещё дальше?двигатель?
@Александр-л6м3м Жыл бұрын
@@GoBrogarageон не разборный?
@GoBrogarage Жыл бұрын
@@Александр-л6м3м а зачем если он рабочий
@maksim33279332 жыл бұрын
Машинка мирка дерос начинает крутится сразу при нажатие на кнопку включения и не реагирует рычаг пуска.
@GoBrogarage2 жыл бұрын
С таким не сталкивался, скорее всего нужно обратиться в сервисный центр или хорошо все почистить
@GoBrogarage2 жыл бұрын
теперь и я с таким столкнулся, не скажешь как с этим решил вопрос?
@maksim33279332 жыл бұрын
@@GoBrogarage человек электронщик сказал нужно перепаивать на плате транзистор вроде ну у него таких нет.
@GoBrogarage2 жыл бұрын
@@maksim3327933 ну емае, сегодня отнесу машинку в сервисный цент, посмотрим что скажут, так как машинка начала сама отключаться во время работы
@GoBrogarage2 жыл бұрын
Отдал на диагностику в сервисный центр.
@РомаЕвтушенко-и1у2 жыл бұрын
Еще б побольше коментировал , было б информативней. Познавательно
@GoBrogarage2 жыл бұрын
Рома вся суть в разборке и сборке машинки) Спасибо
@mvl34647 күн бұрын
some sites sell the electronic card without the programming, fortunately you can find some that also do the programming, you need to give the serial number for this to be done correctly.
@АлексейРыбакДальнегоВостока272 жыл бұрын
Лайкос тебе за видос.
@GoBrogarage2 жыл бұрын
Спасибо :)
@tudopinturas87704 ай бұрын
Como chama essa peça que você está segurando
@_gt63_2 жыл бұрын
Паха лайк тебе за видео, и мои поздравления за первую тысячу твоих подпищеков так держать и побольше интересных видосов.👍👍👍
@GoBrogarage2 жыл бұрын
Спасибо большое за поддержку)))буду стараться)
@QWERTY7773 Жыл бұрын
Don't know if this will help but i bought the Deros and used it for 4-5 years so out of warranty. Then it started playing up then one day (using the 125mm pad) it would stop working one Minuit it worked then when i pushed the paddle the red light would flash and nothing. So i unplugged left it then it would work then do the same. So went on here watched the videos stripped it down cleaned it but to be honest it wasn't that dusty as i always use my mirka dust extractor. Ran it with no pad worked fine then put the 125mm pad back on used it same thing happened. So more videos and research stripped it down again only this time i removed the plastic cover that surrounds the spindle (can't think its name) cleaned the fins which again wasn't that dusty put it back together only this time instead of the 125mm pad i put the 150mm pad on (less used) and it works now (i will keep u updated) Conclusion the only thing i can add is in one of the posts i saw said when somebody had a similar problem was they noticed the pad was worn but initially i wrote this off as when has a sander stopped working due to a pad. However i don't know whether my slightly worn 125mm pad has some how interfered with the brake that slows the machine down when you release the paddle or was it the cleaning that sorted it which i doubt as it was quite clean anyway hope this helps.
@GoBrogarage Жыл бұрын
Привет!большое Спасибо друг за такой подробный и расширенный комментарий, я бы попробовал что то сделать из твоего совета, но не так давно продал эту машинку в неисправном состоянии.надеюсь мое видео было полезным для вас) быть добру!
@nasyas94182 жыл бұрын
Ну с 1к поздравляю!удачного развития канала😊
@GoBrogarage2 жыл бұрын
Спасибо большое)))
@queensferry3282 жыл бұрын
Great video! I had the same problem and when I've tried to screw the motor back in place, I recognized that the thread was full of glue (this grey stuff) at some points. I wonder if the motor will stay fixed without the glue. Do you have experiences? Thanks a lot!!
@GoBrogarage2 жыл бұрын
thanks for the review friend) the motor didn’t last long without glue, 2 months and unscrewed again, disassembled it again and filled the thread with glue while holding) I apologize for my English) this is Google translator😀
@queensferry3282 жыл бұрын
@@GoBrogarage Thanks! This helps me a lot. I'm gonna glue it as well.
@Steinstra-vj7wl Жыл бұрын
You know what is remarkable? That we never see these kind of "repair" videos regarding the Festool ETS EC 125 / 150 sanders. I saw 3 of these Mirka Deros repairs already here on the tube. This sander should cost half of what it does now !!!
@mattgloss8580 Жыл бұрын
dzieki kolego, pomogłeś bardzo.
@SHASHA-de2wp Жыл бұрын
Hi I have a problem with engine (not the link or the card). I have court circuit (short circuit) Do you have an idea if it can be repaired ?
@gudzev7810 ай бұрын
А какая конкретно модель? Мне принесли на ремонт но там кишки другие совсем
@GoBrogarage10 ай бұрын
По модели уже не скажу, я продал эту машинку.
@asdad238510 ай бұрын
Hello mate just done that to mine but it keeps cutting out, what do you think it could be
@VasilKostak-l7c9 ай бұрын
При нагрузке загораетса красная лампа!В чем причина?
@GoBrogarage9 ай бұрын
Красная лампа это проблема в питании, скорее всего что то с блоком управления.
@konstantin_r62 жыл бұрын
Обошлось малой кровью) подшипник искал бы лет сто наверно👍🏼
@GoBrogarage2 жыл бұрын
Скорее всего так и было бы) хотя уже смотрел, что можно заказать на неё подшипник 🤘
@jonyzaam815 Жыл бұрын
@@GoBrogarage а где заказать подшибник можно?
@GoBrogarage Жыл бұрын
Как вариант тут tool77.ru/goods/Komplekt-podshipnika-i-shpindelya-DEROS-PROS-Mirka?mod_id=264585887
@pavelkillerx24522 жыл бұрын
Поздравляю с косариком подписковчиков! Такими темпами 100к не загорами 🤙🏼
@GoBrogarage2 жыл бұрын
Спасибо бро)))
@pavelkillerx24522 жыл бұрын
Приз получил! 💰 Удачного развития канала и ждём новых розыгрышей 😉
@GoBrogarage2 жыл бұрын
Спасибо за участие)))скоро будет
@ЮрийГулай-ъ7щ2 жыл бұрын
Я тоже люблю разбирать всякие такие штуковина. Посмотрим
@МаргаритаГембаровская2 жыл бұрын
🔥🔥🔥🔥🔥🔥🔥
@GoBrogarage2 жыл бұрын
Спасибо 🙏🏻 🤗😘
@logotip7302 жыл бұрын
🔥
@GoBrogarage2 жыл бұрын
🤘
@maksim3327933 Жыл бұрын
Новый прикол от мирке мигает левый зеленый диод постоянно, даже когда машинка выключена, вставляешь в розетку и сразу моргает. Не было такого клюка? Подключал по блютуз ошибок нет все параметры в норме.
@GoBrogarage Жыл бұрын
У меня была такая фигня, что то с питанием, после этого у меня сдох блок, перестал плавно запускаться, а потом и вообще начал включаться резко и сразу выключаться сам:(
@АлексейИванов-я8ф4т2 жыл бұрын
👍🏻
@АндрейТычкин-т7ш2 жыл бұрын
видео помогло. лайк
@GoBrogarage2 жыл бұрын
Рад что полезно!
@bajik282011 ай бұрын
Спасибо за видео
@vitalpanchenko89242 жыл бұрын
Отличное видео!
@GoBrogarage2 жыл бұрын
спасибо друг)))
@Samio_Akkerman2 жыл бұрын
Опа, третья рука выросла!!😜😜😜
@GoBrogarage2 жыл бұрын
ага)))
@mickf5489 Жыл бұрын
Так за что такие деньги платить? Есть ли более бюджетная альтернатива? 🤔 И если можно пару слов о гарантии?
@GoBrogarage Жыл бұрын
Насчёт гарантии могу сказать одно, она у мне проработала в жестких условиях более 6 лет, а насчёт того стоит ли она этих денег, есть альтернатива от Rupes, китайские машинки есть, но я ими не пользовался.от Rupes у меня есть пневмо машинка, хорошая, но нужен хороший компрессор к ней.
@mickf5489 Жыл бұрын
@@GoBrogarage спасибо 👍
@АнастасияЛебедева-я7и2 жыл бұрын
😄🤘🏻
@GoBrogarage2 жыл бұрын
🤘😁
@ИльяЗахаров-ь9з2 жыл бұрын
Увавствую в конкурсе)Паша лучший
@GoBrogarage2 жыл бұрын
спасибо Илюха))
@ЕкатеринаСтаровицкая-у2г2 жыл бұрын
Крутяк
@GoBrogarage2 жыл бұрын
спасибо)))
@ГеоргиосПетридис Жыл бұрын
Подскажите, ключь открутить подложку,, на скока он?
@GoBrogarage Жыл бұрын
Вроде на 24, не помню точно
@ГеоргиосПетридис Жыл бұрын
Спс,, попробую!
@МаргаритаГембаровская2 жыл бұрын
И я хочу денег😆 но видео зачетное 👍
@GoBrogarage2 жыл бұрын
Ну Спасибо)))😁
@АрсенИбрагимов-и2к2 жыл бұрын
Где можно заказать запчасти
@GoBrogarage2 жыл бұрын
Надо смотреть в интернете, я не подскажу, я в ней не менял ничего.можно в сервисный центр Mirka обратиться.
@АясРайков Жыл бұрын
Спасибо друг! Ты меня буквально спас.
@GoBrogarage Жыл бұрын
Пожалуйста!рад быть полезным кому то
@АясРайков Жыл бұрын
@@GoBrogarage а ещё вопрос - на подошве уже второй раз перестает работать липучка. Даже через прокладку. Не знаю, от чего
@Samio_Akkerman2 жыл бұрын
На фиксатор резьбы надо😉
@GoBrogarage2 жыл бұрын
Да я думаю клея туда капнуть через шприц)
@SergeiKlest Жыл бұрын
клей и пластик будет ли держать. Я б вбок стопорный шуруп вкрутил)
@valeriyzhiharev21692 жыл бұрын
Вот блин! Я думал увижу, как разобрать этот двигатель, чтобы заменить подшипник. Больше про разборкумирки ничего не нашёл
@GoBrogarage2 жыл бұрын
Ну видимо у этой машинки подшипник не так часто ломается)))я тоже думал что это подшипник но оказалось нет.
@valeriyzhiharev21692 жыл бұрын
@@GoBrogarage также разобрал, продул, но чувствуется подклинивание при вращении рукой
@GoBrogarage2 жыл бұрын
Гарантия уже закончилась?
@valeriyzhiharev21692 жыл бұрын
@@GoBrogarage вроде как закончилась, она не моя
@barrymccann5600 Жыл бұрын
Google exploded view of mirka deros. You have to remove a split washer on top of the motor and the bearings come out. But it's an expensive sander to make a mistake