mitsubishi outlander steering angle sensor fault

[@ldaly4621]

Thanks for this information. I recently had a "power steering service required " message on the dash . Diagnostic said " high voltage " and "low voltage " fault . Turned out to be a fault in EPS unit . Main dealers say they never had this problem before

[@JonathanHernandez-zv6md]

How did you got to solve the Issue? Did you replaced the part ?

[@Dinamikass]

Its posible to fix, but you must go inside epprom chip and fix data. Before that you must try recalibrate sensor with diagnostic tool .

[@MatikuOfficial]

Bro which one is the one that gives the asc off? The first yellow wheel that you removed or the second one behind that white plastic things? Thanks

[@Dinamikass]

Its second one, first is airbag spring cable.

[@MatikuOfficial]

@@Dinamikass thanks bro

[@juliandavidburbanoburbano8031]

Do you have the file to program the EEPROM of the steering angle sensor?

[@Dinamikass]

No

[@laszlohorvath3997]

Did the sensor need to be replaced? Or did you fix it? how? i have citroen c-crosser. thank you

[@Dinamikass]

Its posible to fix, but you must go inside epprom chip and fix data. Before that you must try recalibrate sensor with diagnostic tool .

[@bahattincam7486]

Eprom nasıl düzelttiniz

[@scientist100]

I replaced a sensor with a used one and still giving the same codes. I'm thinking it is the power steering internal sensor in the power steering unit unless the car only needs new one and not used for replacement. Let me know what you think.

[@Dinamikass]

after you change you must calibrate sensor with diagnostic equipment, also its possible you replaced damaged sensor

[@scientist100]

@@Dinamikass I tried calibration but it fails. Set those codes immediately during key cycle. When I checked freeze frame the angle is read over 700 degrees but when I check live I don't see the angle change at all. Not sure which sensor sends the angle position to the scanner, it only says "steering angle" for data pid. I have tried two other used sensors but those did not talk to the scanner at all.

[@Dinamikass]

@@scientist100 try to calibrate with other diagnostic equipment

[@KingsleyC.O]

Hi @@scientist100, I have a similar issue with my 2010 Outlander. I know your post is about 1 year ago, but I was just wondering if you could share how you managed to fix the problem. Did you try to calibrate with other diagnostic tool as @Dinamikass suggested? Kindly share how you fixed the problem. Thank you in anticipation of your help

[@nikolaiatanasov]

Благодаря!

[@ramzis8893]

Kaip su tavim susisiekti? Reikia mano mitsui ta pati padaryti.

[@Dinamikass]

864148008

[@morristialaveals466]

What did you do to fix it pls

[@hawkeni6475]

have you cleaned sensor, if so how

[@Dinamikass]

If you need clean , you can try open it and blow with air

[@MitchellHubert]

The sensor you tried to open is faulty, replace it

[@Dinamikass]

i have repaired it and its works again

[@hamykay2372]

@@Dinamikass how did you repair it? any problems now?

[@Dinamikass]

@@hamykay2372 fixed eprom inside sensor after calibrated from new in car

[@mantaskirpsas5054]

Ar pataisei mašina?

[@Dinamikass]

Dar nebuvo laiko, bet jau greit, eproma reikia perrasyti

[@adomasmarcelis6758]

@@Dinamikass dėl ko reikia perrašyti?

[@Dinamikass]

@@adomasmarcelis6758 nes nebeina sukalibruoti, kazkas pabega

[@adomasmarcelis6758]

@@Dinamikass sutvarkei?

[@Dinamikass]

@@adomasmarcelis6758 taip viskas veikia

[@mantaskirpsas5054]

Bet tipo prieš tai viskas veikė?

[@Dinamikass]

Pries vairo koloneles restauravima , taip viskas veike