Mitutoyo digital caliper repair is easy

[@DamLins45594]

My 6" Mitutoyo did the same blinking display yours exhibited today. I disassembled it to clean the rail, the wipers, everything, but it appeared it was completely dead. Then I noticed that if I was holding the battery gently inside its case, the display never began it endless blinking. I thought I'd try a little additional pressure on the inside of the plastic battery retainer cap. I folded up and cut to size a small triple layer of paper towel which applied that same gentle pressure against the battery, and it now works flawlessly again. Give it a try before you buy a new display/electronics unit.

[@matthewburke5645]

Video wasn't helpful but your comment was! I shimmed the battery with a folded post-it and its working now.

[@scottvance74]

My thoughts exactly. When he showed the it was blinking with the battery, the battery contacts were clearly the most likely issue.

[@GreenAppelPie]

Thanks for the video, I have a 500-351 that was eating batteries and giving and 05 error. I completely disassembled, including the PCB and cleaned it up with a q-tip and acetone. Now its good as new and saved over $100 for a similar new Mitutoyo. A PZ00 was the best tip I could find for this job.

[@craiglawson9582]

Great Job !!!! As stated below, you were clear and concise on describing how to disassemble the unit. Thanks for sharing.

[@saxonstc]

Where can get the Spare parts for replace..? Can I get it online ?? And what is the part Name..?

[@slimmmerman]

Where do you buy the display from?

[@marklatham5692]

Very nice video, concise. Am hoping you will make some more along these lines!

[@rcsenan]

Very good and useful

[@pieterschiltz]

Legend !!! I found 30 broken ones so this vid is very handy ordering my screens asaap

[@Mogman150]

What is the cost of the electronics/display? I'm guessing it might be a high percentage of the cost of a new unit?

[@prestigeworld-wide8292]

Jeez. I was hoping to see the inside of the unit. This is a plug and play demo.

[@BRODGLENN]

very nice and detailed demo.. but where to buy the spare parts?

[@jacksavill8691]

`Anyone ever find a supplier yet ???`

[@Tony49Romas]

I’m looking for the lcd display, does anyone knows where to get it?

[@muhammadzakria3482]

just press all the buttons same timed wait for 5 to 10 seconds. it will be alright no need to open. i did. it works.

[@robertarmour3264]

Any idea what size screw holds the battery cover on?

[@richmyers416]

If you hold the origin button for 5 seconds after a new battery it fixes that issue an no need to replace the display

[@LUKAJA3]

Not always the case. I changed bateries in mine yesterday and this problem is stil present. And I will defenitly try this. if it will solve my problems. Thanks for the nice video.

[@canallulepelomundo9139]

Onde encontro pra comprar está parte,pois o meu paquímetro não funciona mais

[@otpipe]

Mine was blinking just like that one and I just depressed and held down the ORGIN button and it went back to normal operation.

[@Bosnia1291]

His was not blinking. His was stopped to blink liked freezed. But thank you. I changed the battery and my was blinking too. Now it works well after push the button 😘

[@gringostarr69]

What battery does it use? I have a mitutoyo 500-311 model cd-15d

[@chido5722]

Donde puedo comprar el displey de un vernier de 24" mitototoyo

[@galeotto1988]

Hello my mitutoyo caliber screen's is broken.. can you tell me how I can fix it?

[@jcg0324]

Are you sure about using a "phillips" screwdriver? If made in Japan, wouldn't those screws be JIS screws?

[@Majorvideonut2]

Just bought one and opened it yesterday and checked it out and all was working perfect. Today I go to the shop pick it up and can't move the jaws with the thumb screw. Help!

[@joshstevens76]

Any chance the depth gage rod can be re-attached?

[@pcrashford5367]

What if it turns on but it doesn’t read when you adjust?

[@that8506]

The 189 webpage no longer seems to show prices, or even parts. Do you still support this caliper or is it something best ordered through MSC? I'd rather buy from the "little guy" especially if they're posting up good how-to videos like this.

[@cpd969]

What are those two holes on top of the (I’m not sure what to call it) electronic body just where the tensioning knob?

[@Kinann]

They control the amount of friction you have when sliding on the beam.

[@ELECTPROG]

Saved my Digital vernier which was factuating reading earlier

[@umargul5644]

Great job sir

[@ikifkif]

yes but the display was working (blinking) the origin button goes on these.

[@hydrashocker]

Replace the battery, then press and hold the "ORIGIN" button. Then it will reset and come back up to 0.00".

[@heklik]

Mine have LCD burn.

[@ernestoz6351]

What’s a error 5 means?

[@dsplit]

About how much would a new electronic board cost. I have the same model you are repairing.

[@JWGrum]

www.longislandindicator.com/p189.html please take a look to see if your model is listed on this parts page

[@kumaresanRamamoorthy-fp3sw]

I want that spare

[@deemdoubleu]

nice video well presented

[@TrailBusterBrute1]

For the cost of these things the display should always work, barring damage!

[@alvaroz6]

45/5000 where can I buy the screen of a caliper

[@CAMAROG9]

Here you can get a parts list directly from Mitutoyo. From there you can go to your local supplier. www.mitutoyo.co.jp/eng/support/service/parts_list/attestation.html

[@Tony49Romas]

CAMAROG9 They just give information of the reading unit. I’ve been looking just for the lcd display too, does anyone know where to get those?

[@alquemir]

@@Tony49Romas It says on their website you have to send them an email with the part number.

[@walterallen8478]

Thank you.

[@Doggie504504]

Your should use a JIS screwdriver not Phillips.

[@ClownWhisper]

They're high precision machine screws they're not self tapping lol

[@ing.josegarcia7316]

hello, I need the electronic board for may caliper mitutoyo CD-8 ASX, CAN can sell me

[@JWGrum]

www.longislandindicator.com/p189.html please take a look to see if your model is listed on this parts page

[@ing.josegarcia7316]

Ok,

[@robertschlitters5764]

Need to change the video title. This is a Digital caliper. Not a Dial caliper.

[@Maxim.Teleguz]

kzbin.info/www/bejne/qouwonZul5uYjrc - simple solution if you haven't tried this.

[@vickylorenjaya]

dicariin ama temen gua tuh si pamuji punya dia ga bener bener tepu tepu

[@sainathpatil4454]

Thank you