MN99S | DIY SERVO MOUNT | LOW COST SETUP | BODY TILT PROBELM | PROBLEM SOLUTION | BEGINNER MOD

In this video i will show how to solve body shell tilting problem during steer left or right.
The most common issued by for beginner user. They asked:
" why the body tilt during steer left and right? "
" Is there any solution for this kind of problem "
So in this video i will show the simple solution and low cost setup for this kind of problem for new user.
What you need to do, place the servo near the axle so the steering movement will become more smooth and the body will stop tilting during steer.
material you need:
1. M1 size screw with nut.
2. Hard plastic/Hard metal sheet for the servo mount.
3. Cable tie to hold the servo in place
4. Super glue used to hold the cable tie in place.
If you had any question regarding this modification just comment on the video.

[@rcn8tiv345]

I actually have a question regarding this exact rc, but it doesn't have anything to do with the servo....although this is a very helpful video....but it has to do with the stock gearbox see, and im trying to raise it a bit for more ground clearance....any advice?

[@RCFANATIC92]

Hello. If you want to raise a bit the stock gearbox, what you can do is, make a new hole on the chasis to change the gearbox placement. Because mine also the same. I make a new hole on the chasis to raise the gearbox a little bit.

[@jaysendeluna3693]

Hi, Did you cut the plastic cover to avoid the servo from damage when bouncing?

[@RCFANATIC92]

Yes..i cut the plastic cover, so the servo had more space to move. Before i cut the plastic cover the movement very limited due to the servo hit the plastic cover when bouncing.

[@jaysendeluna3693]

@@RCFANATIC92 thanks!

[@mclatoscream]

Can i changes my stock servo mn90 like that? Or i need to buy esc or something to buy to function servo?

[@RCFANATIC92]

Hello sir, for those using mn90 model, the steering mechanism still using motor to steer left and right. If you want to used servo you need to change your stock esc by using esc board that can support servo plug in.

[@mclatoscream]

@@RCFANATIC92 no need to buy remote transmitter? Only servo. Tnk

[@RCFANATIC92]

@@mclatoscream if the esc board support servo plug in..no need to change the transmitter. if you buying a new esc, so the transmitter also should be replace with a new one.

[@mclatoscream]

What if i change the plug in of a servo? Can harm battery or any. Thank thank for your time frnd.

[@RCFANATIC92]

@@mclatoscream if you plug in a new servo their is not harm to other component or battery. But its depend on your esc also sir.

[@sportshighlights5839]

Bang kalau tukar chassis metal kena tukar servo kah ….kah blh guna servo standard

[@RCFANATIC92]

Boleh jg pakai tu servo standard tapi ada berat skit lh mau steer sbb tu chasis smua besi sdh..paling bagus upgrade servo pkai 6kg atas punya servo..tu jx servo 3kg pun alang2 jg tu kalau pakai..😅

[@PlancksTime]

Which wheels are those?

[@RCFANATIC92]

its a 3d printed wheel i bought from a local store in my country. Tyre i'm using MN stock tyre.

[@jamaicarctv9587]

excellent video my friend

[@RCFANATIC92]

Thank you my friend..

[@kenjidalit995]

What is your rim my friend

[@RCFANATIC92]

Im using 3d printed rim extension bro.

[@capciphoby7944]

Sangat membantu🙏🇮🇩

[@RCFANATIC92]

Terima kasih bang

[@Valnabalu]

Brapa besar servo kau guna? 9g? 17g?21g?

[@RCFANATIC92]

Pakai yg 18g metal Jx servo 3.5kg..tp kalau dlm video nie pakai stock servo mn99s

[@Valnabalu]

​@@RCFANATIC92Thanks bro. Sya mau upgrade servo d90 sebab stock servo dia buruk 😆😆

[@RCFANATIC92]

@@Valnabalu 😄..welcome bro..tp sy rekomen ko pkai besar sikit lg servo dr tu 3.5kg punya..ko pakai 6kg atas punya servo..sbb kalau byk sdh ko mod tu rig jd berat mcm nda teangkat sdh tu servo tu..kalau mcm 2kg punya berat rig masi ok lg..3kg ke atas nda brapa sdh tu servo tu..😆😆

[@Valnabalu]

@@RCFANATIC92 oh thanks for the tips bro. Make sense. Sia ada terbeli 25kg punya servo tapi mcm terlalu besar pula. Kalau tekan ja absorber kena tu body parts dia. So sia kira pakai 21g punya servo ja yang metal gear. That's how i encountered your video 😁😁 harap boleh angkat la berat tu kereta 😅😅

[@Valnabalu]

Oh ya bro.. 21g punya boleh angkat 4.5kg kalau nda silap. Metal gear servo. Itu yg sia beli. Maksud sia sia ada terbeli 25kg punya servo..besar eh. Mcm tuk 1/10 punya rc. Kena frame.kena tray juga.. nda muat hahahha

[@tiwairubus4327]

Bg kalau nk upgrade..nk upgrade apa dulu bgus?

[@RCFANATIC92]

Kalau saya..better tukar placement servo tu dlu..sbb nk bagi kurang body goyang bila steer kiri dan kanan..Tukar axle gear pkai full metal..lepas tu bru tukar motor, esc dgn receiver. Lain2 komponen tu pkai standard pun ok jg..

[@tiwairubus4327]

Ok tq info

[@tiwairubus4327]

Bang kalau upgrade servo..utk conection ke esc ori smh jugak ke?

[@RCFANATIC92]

@@tiwairubus4327 sama bro..pakai 3 pin slot jg..

[@tiwairubus4327]

@@RCFANATIC92 tq👍bru nak bjinak dgn rc..kalau ada apa2 nanti tnya lgi..trima kasih byk2 info

[@amirfahim2591]

Bang kenape mn99s saye lepas masuk air terus x hidup..boleh tau tak sebab ape?

[@RCFANATIC92]

Standard kilang atau dh tuka brg smua..😅😅

[@amirfahim2591]

Standar

[@amirfahim2591]

Lampu hidup cume tayar dngan signel x hidup..

[@RCFANATIC92]

@@amirfahim2591 kalau standard kalau tk buat waterproof mmg kong lepas masuk air..😅😅..cuba kering kn board smua..lepas tu bru on..

[@adityasandy7638]

tyre cantik bang. tyre apa tu bang?

[@RCFANATIC92]

Tayar mn standard ja bang..tp pakai rim 3d printed tu

[@kundasangranausabahdrone4436]

Terima kasi..mantap.

[@poksu_gg]

Tutorial pasang servo takde ke bro?

[@RCFANATIC92]

Sorry..saya cuma buat video walkthrough servo dgn just bagi tahu nak adjust servo mcm tu ja..ada masa nt saya up video

[@wesleybuaya7079]

Abg rim tu beli dekat mna

[@RCFANATIC92]

Beli dkt shoppe bro..ini link seller.. shopee.com.my/product/1447857/7355598137?smtt=0.54304523-1625919101.9

[@zmh1574]

Kalau saya pakai servo MG90S tapi Masih electronic stock MN boleh masuk ke?

[@RCFANATIC92]

Asal plug servo tu boleh cucuk kt esc ori..boleh ja pkai bro.

[@zmh1574]

@@RCFANATIC92 terima kasih

[@RCFANATIC92]

@@zmh1574 sama2 bro..

[@riyyyfishing4713]

Uishh..lawa bah rim bro..mana mau dpt bro..?ada link nya ka..?

[@RCFANATIC92]

shopee.com.my/product/1447857/7355598137?smtt=0.54304523-1622780607.9..ini link seller tuan..mcm2 jnis accessories jg dorg jual nie..cuci2 mata dlu bh..haha..smua brg 3d printed..kualiti brg pun bagus jg..

[@МихаилМяснянкин-л5ш]

Hello. Where can I find such wheels?👍

[@bidishachatterjee2]

IN OHIO

[@Hazel-co3qi]

Cantik rim kau bos.. Nmpk real.. Minta link pembelian..

[@RCFANATIC92]

Ini link rim..nie seller bnyk jual accessories rc jg nie..👍👍.. shopee.com.my/product/1447857/7355598137?smtt=0.54304523-1643002393.9

[@Hazel-co3qi]

@@RCFANATIC92 oh.. Mantaps.. Terima kasih cip..

[@RCFANATIC92]

@@Hazel-co3qi sama2 tuan..👍😊👍

[@poksu_gg]

Terbaik bosku

[@mahyukiyukiee3621]

Bang...ini servo berapa kg bang...dan ape namanyaa

[@RCFANATIC92]

Nie jx servo 1181 digital 3.5kg..bukan waterproof..

[@haergensteinjackson7616]

bang mintak link rim

[@RCFANATIC92]

Link utk rim shopee.com.my/product/297660372/7547457364?smtt=0.54304523-1634426915.9

[@vironvr5604]

👍

[@RCFANATIC92]

👍😁👍

[@Yosefu93]

Can someone summarize this i english hes just showing what he did not how he did it 🥲

[@RCFANATIC92]

Hello.. This video uploaded because of the issued body tilting problem during steer left or right for stock MN Rc. This kind of setup is for budget setup, by using handmade bracket for the servo to mount on top of the front axle. If you have an extra budget you can buy directly the servo mount and assemble on your axle PNP so the problem for body tilting steer left or right will be solve.

[@Yosefu93]

​@@RCFANATIC92how did u make the bracket

[@RCFANATIC92]

@@Yosefu93 Im using hard plastic plate..cut into size the servo you using..the plate act as a mount for you servo..but you can buy the alluminium mount at rc store..