Mobility Scooter MOTOR REPAIR Guide! | Watch My BASIC Mobility Scooter Motor Refurbishment Guide

[@themobilityguy]

‼ Lot's of people asking for my email or website, visit www.themobilityguy.com to get in touch via the contact form!

[@claydo364]

Thankyou P,nut🤙

[@jamesd9337]

I've just done my shopriders motor and when I pulled brush housing off that black wobbly washer came flying out. After I cleaned it and was about to put it all back together I had no idea where that washer was meant to go back. Been searching all day and this was the only place I could find even a sign of where it is meant to be. On top of the BBS. 3.am😓 Thank you so much for doing this video. Really has helped me.😊👍

[@themobilityguy]

Glad to have helped , them washers tend to disappear fairly quick, glad you found it!

[@jamesd9337]

@@themobilityguy are there meant to be 2 of them washers? One under the BB and one sit on top?

[@themobilityguy]

@@jamesd9337 I think it’s only the top one as the bottom one usually sits in a flush bearing Don’t think it would be really really bad if you were missing one but again I think there was only ever one in the top that goes in

[@jamesd9337]

@@themobilityguy thanks so much for getting back to me quickly. Legend. 👍

[@jamesd9337]

My 16 year old shoprider is running lovely now. Well happy.

[@kayakcaster1073]

Great info . Thanks. Advise you get a tripod. To stabilize picture. Thanks.good work.

[@claydo364]

So if nothing is beeping everything is fine .yer...and if or when me motors stuff up this beeping sound will go off .Is that what ya saying 🤔

[@itsjustandrei508]

What types of bearing i need for the same motor in side with brushes ? I cant find the code from old bearing because of the friction insids and it s melted

[@claydo364]

Now the trans,axle parts

[@wobblybob7029]

How do you get the pins back in without them sticking to the magnets

[@nuetral2374]

Great vid very helpful 👍🏻

[@victorkim2843]

Very helpful ! Thank you very mucho.

[@vikkidyer]

Hi do you know if there is a way to use a escooter controller on a powerchair ?

[@themobilityguy]

Easier to replace the controller with the correct one and not jerryrig something together, at the end of the day someone is in it and it’s somewhat dangerous going that route converting

[@vikkidyer]

Ok thanks for the reply. I've had 2 people look at it and they can't figure out what is wrong with it so I guess it's getting scrapped 😊 xx

[@mariaelizabethchinchillafo791]

Hello, I have a Ventura DLX4 Scooter, it has a strange problem, sometimes it is stopped, and when I accelerate forward it does not do so, suddenly it accelerates with a sudden force that is dangerous to hit someone, sometimes it is difficult to start the acceleration . When I try to move backwards he does it with little force and with pushing. A technician changed the drivers, he said that was what he had, but he keeps doing the same thing. Any suggestions or help to repair it. I appreciate it a lot.

[@RonaldDaub-v9y]

Sounds like brushes worn out

[@tonyheaton3343]

Hi thankyou first of all for this video its helped my partner so much but we have a problem what size tool did you use (alan key) to get the grub / grommet out please please help my motor is alot bigger than this its a 950w freeriderfy1 luxury id imagine the grommets are all the same size ? Thanks in advance to anyone who can help 😮

[@claydo364]

Feel..the size of the hole. She the hole might be a 3 quarter inch🤣🤣🤣🤣

[@rickanthony8259]

Awesome! Thx, ill try tomorrow!

[@tbonesenior6736]

Great job, my wife's scooter gets a 10 flash is it a battery problem??

[@dereckryan275]

10 flashes or beeps means excessive voltage has been applied to the controller. You need check the battery connections. This is usually caused by a poor battery connection.

[@user-ud4dc7rv1h]

I cleaned my scooter motor following your video. When I put the motor back in the scooter, it goes in reverse when I want to go forward, and goes forward when I want to go in reverse. Also, the brake no longer will engage. I put the motor together just the way I took it apart. Please help!!!!

[@themobilityguy]

You didn’t put the motor together correctly , the motor had two magnets built into it , south and North Pole So , the case of the motor is 180 degrees the opposite of what it was , take out the two bolts on motor and turn the case of the motor 180 degrees , and screw it back in The brake not working , unrelated to motors as that’s a separate connection, so you’ve either buried the brake disc onto the head of the motor as you’re supposed to line up the head of the motor to the brake disc that’s inside the brake , or you’ve got a connection issue or the brake is in neutral

[@RonaldDaub-v9y]

The brakes are power robbers anyway electromagnet on the whole time you're running

[@bksduskmirror1250]

Could this be the reason the motor gets hot and the scooter slows down to a stop after running for 1/2 an hour?

[@themobilityguy]

Yep but also worn brushes could cause that too

[@adeymekbib8761]

Is there a liquid cleaner or degreaser I could use instead of sand paper, that won't harm the motor? Could I use dish soap and a toothbrush for example?

[@MadPaperPeople]

paraffin might do it

[@MichaelMiles-zs4px]

Use a proper commutator stone to get that fixed up

[@stevenprestwich521]

Do you know why my scooter goes downhill to fast, it's ok on normal roads

[@themobilityguy]

Gravity … like a car would

[@paullacey748]

Take your thumb off the throttle. When going downhill you only need enough throttle to keep the brake motor off.

[@claydo364]

So I was riding along on scooter when steering damper came undone😅😅no shit

[@RonaldDaub-v9y]

In between each brass commutator connector. You need to undercut the commentator with the special tool. Or it would be one step better.

[@themobilityguy]

Thank you will check this out

[@tvolz40]

You see that needle jump? Yea it jumped across the room is alli saw lol

[@themobilityguy]

I am still trying to find this needle that jumped across the room, if you managed to see it in the video please tag me with the time stamp 🙃

[@fernando87613]

😊

[@oldbob8033]

I promise to write a vlog to show how to change the motor brush's and clean commutator this guy is at a loss

[@themobilityguy]

I promise to ignore attention seeking idiots like you 🤪

[@themobilityguy]

And let me know when you figure out how to “write” a vlog, you little genius 😉

[@claydo364]

Ok dum dum what did you claim all the parts with? Not petrol I guess

[@dennisderosia72]

Please learn how to use a video camera. Took 2 minutes to get over my dizzy spell.

[@themobilityguy]

🤣

[@TerryHenderson]

Terrible Video All That Wild Motion Getting Me SeaSick !!!!

[@themobilityguy]

Then take a travel tablet before you watch it you poor thing 🤡

[@claydo364]

A 700 motor?🤣🤣🤣🤣

[@themobilityguy]

I’ll correct it when you fix the grammar errors below: Travis Claydon dose 2000,5kilo weights A Da... My brain hurts thanks