MOD KIT INSTALLATION UPDATE

[@af6727]

I've watched alot of OLED installation. Yours seems to be the only one that has secrets of the trade. i.e straight pin for CPU cover, optimizing adaptor fitting, and minimzing shorts. You're the real deal in my book.

[@sthetixofficial]

thank you

[@riquelmeneymar5515]

@@sthetixofficial amigo unas dudas el conector DATO lo pones , soldas , tal como muestras en tu video , O LEVANTAS PRIMERO EL.COMPONENTE Y YA DESPUES PONES ABAJO EL FLEXOR DAT0?? y otra pregunta ese flexor en forma rectangula coñor negro que soldas que es ? Y donde puedo conseguir eso ?? Y exelente video , espero respuestas saludos gracias.

[@sthetixofficial]

The black one is shitty, use the yellow dat0 adapter. And I did not solder it because : The eMMC chip has undergone a heating process inside the factory with precise parameters and an ideal environment. Reheating the eMMC chip in a DIY method will alter the crystalized lead-free tin balls under it. And at some point, the ball will crack due to heat from the console or other factors like moisture, external force, etc. So I chose the less risky, less hassle method to install the DAT0 adapter, so the repair process will be less hassle when it fails. BTW, can you guarantee that your chosen method is 100% perfect without failures? I guess not.

[@riquelmeneymar5515]

@@sthetixofficial oye pero TODO LO DE TU VIDEO QUE SUBISTE , ASI SE HACE O CORTASTE PARTES DE TU VIDEO , QUE NO SALEN PARA VER EL PROCESO O ASI ES TODO PROCESO COMPLETO PARA LA INSTALACION

[@riquelmeneymar5515]

@@sthetixofficial y todo esos componentes que utilizas , donde los compras para poder hacer mi instalacion ???

[@samdogygaming918]

Love the fact you don't have to reflow the eMMC with the Dat0 adapter anymore felt like this was the main reason I shied away from this. Another great Sthetix video.

[@riquelmeneymar5515]

Amigo el flexor DAT0 ese solo va asi puesto , soldado como lo muestra en video , o hay que LEVANTAR EL COMPONENTE PARA PODER PONER EL DAT0 ?? espero respuesta saludos gracias

[@samdogygaming918]

​@@riquelmeneymar5515 "06:55 INSTALLING THE DAT0 ADAPTER " ( No need to reflow the Dat0, slide adapter under the chip) No es necesario refluir el Dat0, adaptador deslizante debajo del chip.

[@riquelmeneymar5515]

@@samdogygaming918 cuando dices refluir a aue te refieres ?? ( ENTONCES TAL COMO EL LO HACE EN VIDEO ASI SE HACE PARA INSTALAR EL CHIP ?? y oye por que empezando cuando esta instalando el dat0 , raspa unas lineas por que ?? Por que raspo ?? Que se supone que va ahi?

[@Char-nx3de]

@@riquelmeneymar5515 reflow(refluir) lo más seguro que el traductor se lo puso así , se refiere a levantar la emmc no es necesario solo con el adaptador como se ve en el vídeo y la soldadura quedaría de 10

[@papasmurfington5264]

@@riquelmeneymar5515 El DAT0 es muy delgado, simplemente lo deslizas debajo del chip eMMC

[@therealjebediah]

Classic Sthetix W

[@shenmue5765]

Best soldering skills! That little via for CLK signal gave me hell! You blew by it like nothing.

[@airquis]

What was hard about it?

[@jrok96]

​@@airquis people without a lot of experience soldering have problems soldering to little via's thats all. there is very little for the solder to stick to as you know. phrases like "what was hard about it" come off as condescending.

[@FatalBcr]

Complete and Very good tutorial , like always ! GG

[@sthetixofficial]

thank you

[@justadad2222]

Pro tip. I usually put down tape then draw a switch on the tape. Then as I disassemble it I put the screws on the tape using the drawing to put them by the correct place. (Screws are different sizes and helps to get them back in the correct place during reassembly.)

[@johnandrews9433]

Overcomplicated waste of time tip. 😂

[@bigtitmaster]

It’s very easy imo. 4 types for the outer(very easy to distinguish) and 1 type for metal shield, 3 type for motherboard

[@SwitchBros.]

The EMMC-God in his element 😘 Love ya man! Greetings from Germany!

[@LuizFernando-eb4cn]

clean and elegant work. video is clear and highly informative. thanks

[@Danjovisagat]

So subtle I wonder what tablet this is ;D Love the content as always

[@sthetixofficial]

thank you

[@37Kilo2]

I have a v6 en route. Thanks for the guide!

[@QuentinMatthysBoeckmansYJ]

Amazing ! Great instruction video !

[@dazkillinger1397]

😂 wow you make everyone look like straight amateurs. Your a all around complete scholar

[@sthetixofficial]

thank you

[@gedi223]

I wish you were in the US. I'd love an OLED model. I have a day one switch, but really like the bigger screen real estate of the oled for my old eyes.

[@marsimoon185]

Man i Love you! My Chip is on the way to me Because of your videos. I already have a modded old Switch. But now that i know i didnt have to reflow the emmc on the oled. I know i can do it without a problem. Really appreciate your work. Thanks and greets From Germany 👍

[@sthetixofficial]

Glad I could help

[@ceut2004]

Hello ! You have made a great tutorial with great video, thank you! 😃 I have 2 questions to ask you before trying to mod mine 🤗: 1)At 14:18 for the CPU Flex: I saw that you have not soldered the 2 grounds tabs on the bottom, so these 2 points are not really needed ? 2) Is it really necessary to upgrade the firmware at the very first step, before tear it down to put the modchip ? Thank you !

[@sthetixofficial]

1.not needed because, the short cap pad is the gnd 2. don't alter the chip firmware

[@ceut2004]

@@sthetixofficial Thank you ! 😃 Just a precision for the 2) point: it is about the console firmware at 01:42 (and not the modchip FW). As I understand: the firmware will be emulated on the MicroSD card after all that, so no need to update the console before trying to mod it ? Thank you again 👌

[@sthetixofficial]

i usually update the console before modding it.

[@ceut2004]

@@sthetixofficial Thank you (again) ! So I have started to mod my "tablet" - totk one for the v5 kit: I have teared it down yesterday and I have to do the first step now: the DAT0 adapter (I have a Samsung eMMC inside mine 🙂). I follow your guide step-by-step with many pauses on it 😃

[@ceut2004]

After about 1 month having taking my time and doing it very slowly: my totk "tablet" is done 🙂I found my installation very clean, I have followed about all your video, with some personal ideas on cable management 👌The glitch is actually super fast on mine, with samsung emmc 👍 Thank you again for your great video !😇

[@Kostrach]

when lead-free solder quickly crystallizes, it will be brittle and cause cracks, so all thermal profiles for lead-free soldering gradually cool the board to at least a hundred (more correctly, to the solidus temperature of the alloy) and only then the board cools itself. so if you solder dat0 correctly, then there can be no cracks when using the correct thermal profile for both heating and cooling

[@sthetixofficial]

I wont use that method again bro. logically all "friction" connection methods exist on the console itself, like the the flex ribbon cable, the speaker, the screen, etc. Yes they use a solid locking mechanism, that is why i pushed the dat0 a bit before locking it with solder. each person or installer has each own theory but I am sure no one is perfect, including me.

[@Kostrach]

@@sthetixofficial when connecting without soldering, all connector contacts are coated with metals that do not have oxides, such as rhodium or gold. there will be a connection of a solder ball with a cable, and if there is a yellow protective coating on the cable that prevents oxidation, then the ball does not have this. under normal conditions and perfect cleanliness, it will take months. But in aggressive weather, this can happen quite quickly. in Russia, if you do not solder, then such a contact exists for about 3 weeks due to temperature and humidity.

[@sthetixofficial]

I do appreciate your thoughts and theory & facts. But I will keep it this way. I've have even tried to remove the emmc chip and sandwiched a dat0 wire and still.. It cracked after some time - although I have made it sure the connection is secured and used a good solder paste.

[@Kostrach]

@@sthetixofficial to do this correctly, you need to use a lead paste and be sure to remove the old balls. I am using Sn60Pb40 solder. This one cools better not to form micro cracks and has high strength. try it and it should work

[@sthetixofficial]

I already did that too 😊

[@DonnyDjarum]

luar biasa completed bro tutorialnya sukses selalu ilmuna 😍😍😍😍😍😍😍😍.berkah bisnisnya

[@sthetixofficial]

thank you bro

[@hoteny]

Me still watching switch videos without ever owning one for no reason (ok maybe for a reason of ever finding a cool unpatchable exploit news that would make getting switch logical in my country)

[@medafightercross6307]

I always get a different diode value that fall outside the value range you show here. The DAT0 Diode value is either under 0.500V or over the 0.800V. Its the not first time so im guessing its a multimeter thing.

[@sthetixofficial]

it is okay

[@oliveirajose27]

Great video!! A quick question, why aren't flashing it with hwfly-nx? I remeber from previous videos you used to recommend it to avoid some non-sd card installed bug screen and also it was blazing faster than the stock firmware.

[@sthetixofficial]

no i dont use it anymore. the stock is blazing fast now. no need to alter it

[@mustofaalialhamid4121]

Maaf saya mau aktif subtitle Indonesia dan ini tidak sedia subtitle 🙏🏻.. Karena saya mau baca subtitle agar mudah paham 🙏🏻 Thanks 😁🙏🏻

[@sthetixofficial]

Tidak ada subtitle bahasa indo. Sorry ya

[@mustofaalialhamid4121]

@@sthetixofficial oh ya udah.. tidak papa kok makasih ya ☺️🙏🏻 Dan semangat ya.. karena saya selalu lihat video anda terus😁👍🏻..

[@darthpapa696]

I had no idea this is an Indonesian channel. Keep up on work dude.

[@Gusrango]

Nice video. This mod work on the old one ?

[@sthetixofficial]

makasih

[@h.a.6790]

Use of soldermask seems better if you're looking into insulating points since its less destructive.

[@sthetixofficial]

you can use it .

[@papasmurfington5264]

Hi, what do you use for view your PCB when working? Do you use a camera and look at a display (I know these may have lag) or do you use a magnifying glass? Do you have one you prefer?

[@sthetixofficial]

i use a microscope that has a recording capability.

[@dinodin007]

Why not just insulate the two pads with soldermask as opposed to cutting the traces which is well, potentially dangerous?

[@sthetixofficial]

there are many ways to achieve the same result

[@ponciusz]

Hello Thanks for video is 0.468V Correct value from point D I worried that I might scratched it too much and connected with ground.

[@sthetixofficial]

if it is grounded , you will get 0.00 something

[@ponciusz]

@@sthetixofficial its alive ! everything works v5 delux wires instead of extra ribbon. thx for tutorial

[@jgp2290]

Great video! Do you still always update the chip before installing them or do you use the firmware that comes with them?

[@sthetixofficial]

No, I use the stock firmware

[@rna5968]

Hi there! Thanks for this great video. I am planning to install v5 to my oled. Should I use flex ribbon cable for DAC and 3.3 points or shoud I solder points directly on the PDB just like you? Which option is better? Thanks!

[@sthetixofficial]

use wires for those signals.

[@themightythock2836]

This is really nice guide. I'm worried that using the PCB as chopping board for wires might get you in trouble at some point.

[@MichaelGuiyeMonguer]

the best tutorial, I just prepared the clk point without putting in the chip or any other cable and it gives me a value of 1500...isn't it too high? It looks good tinned, should I leave it like this or should I check it? What happens if the values are higher than the 800 you mention? Thank you

[@sthetixofficial]

if it is higher then the point is broken, try to reverse the diode mode reading. red probe on gnd and the black probe on the CLK point and see.

[@MichaelGuiyeMonguer]

@@sthetixofficial I know the point is not broken because the console starts in original mode

[@MichaelGuiyeMonguer]

@@sthetixofficial If I change the tips it doesn't do anything it doesn't mark anything I think maybe there may have been a little scratching or the solder may have been cold. ​

[@NormanMader-rz8ye]

As far as I've followed correctly, the grinder is used in 2 places in the video. In order not to grind through the trace, wouldn't it be better for laypeople to use sharp-point tweezers or a pin?

[@sthetixofficial]

I used the ma ant d 1 mini grinder.. You can always cover the area with soldermask later

[@NormanMader-rz8ye]

​@@sthetixofficial Yes a ma ant d1 mini grinder is used in the video. This i know. But i want to ask: In order not to grind through the trace, wouldn't it be better for laypeople to use sharp-point tweezers or a pin? (and later if they like they use soldermask)

[@sthetixofficial]

Please use any tool that you have mastered.

[@anj2099]

beautiful job.

[@tamasfabian5250]

Great video…used your guide to install on my oled. Everything works except after install, i’ve lost touch capability of the screen. The scree itself works, nice colors but it doesn’t respond to touch.

[@sthetixofficial]

check the LCD socket or near that, maybe something shorted / damaged etc

[@tamasfabian5250]

Thanks for the tip..,my ribbon cable seems little scratched…that’s it, and display is ok…just touch is gone. Is it possible to replace just the ribbon cable for oled or just with entire screen?

[@sthetixofficial]

not possible.. try to fix the broken track

[@TrunksDB-vu2ff]

I have a question. 1. 7:32 I watched the video several times, but the installation guide told me to scratch the two lines on the left, but your grounder seems to have scratched all three lines. Do I just scratch all three lines? 2. 23:30 What is the black tape on the back of the device? Can I ignore it? Your content is always amazing. Thank you.

[@sthetixofficial]

It does not matter because the perimeter of the scratch lines are gnd. It is a double sided tape Thx

[@ErzTubeHD]

Is it necessary or recommended to tin the fork of the dat0 adapter?

[@sthetixofficial]

i didnt use it. but please try it and you will know the durability later.

[@seanong8074]

Hi! I have been watching your installation videos to learn more on the different modchips. I am intending to purchase a oled modchip and i did some searching on aliexpress. Found hwfly v5 and instinct nx v6, i know you have a v6 installation video (i believe the modchip is instinct nx v6 correct?) but i don’t see a hwfly v5 installation video. May i know if i want to install the hwfly v5, which installation video should i reference please?

[@sthetixofficial]

you can see my previous video on my channel about the v4. I don't use v5

[@seanong8074]

@@sthetixofficial is there any difference in installation wise between the v4 and v5? drive.google.com/file/d/1RS-ZEj7ylwQBSueN5KAtEoDlbvWx7G4-/view?usp=drivesdk

[@deevesh]

@sthetix, How often do you need to reseat the dat0 adapter? Mine lasted a week. I think i just soldered 2 points on the ancor but will do the third point like you showed to the capacitor. Hopefully that will keep it in place longer

[@sthetixofficial]

it could last forever. it depends on the material itself and the locking mechanism / installation method / moisture

[@deevesh]

@@sthetixofficial Thanks! good to hear that once i get the installation correct i wont have to open it up again!

[@Notpoop906]

Why do you have to break those traces? Is it to avoid the potential of the anchor shorting against the solder blob the traces lead to?

[@sthetixofficial]

yes correct

[@Notpoop906]

@@sthetixofficial okay thanks for the answer!

[@Paul-sk2pc]

I have a Hwfly v5 chip. Do I need to solder ground pad? Also, the instruction mentions solder 3.3v to both capacitors. Is that necessary or just one like your video just fine? Thanks

[@sthetixofficial]

no need bro. you can just follow the same was as in the video

[@Paul-sk2pc]

@@sthetixofficial Thanks. It turns out both 3.3v capacitors needs to be soldered for the v5. When only one is soldered, the chip has solid white LED and boots directly to stock firmware. The ground can probably do without but I did it anyways. Awesome tip using four anchors friction data0. Also, solder wire directly to the chip like what you did is much more reliable than included flex cable. Looking forward to more contents!

[@sthetixofficial]

no bro. when you look ad the motherboard track, the 3.3V is already tied together. You dont need to solder both caps together.

[@injectx]

I found your video very interesting. I've installed the same kit using the FPCB, but I can only boot into Hekate. I can't access sysNAND, emuNAND, or stock firmware. Would it be worth trying to install it with wires instead of the FPCB?

[@sthetixofficial]

try to remove the connection to the chip and see if your console can boot to the ofw

[@injectx]

​@@sthetixofficial Here’s what I did after my initial comment: I followed your Level 2 video for rebuilding the NAND, but it didn’t resolve the issue. Then, I removed the modchip completely, but now the screen remains black and the system doesn’t boot. I'm considering re-soldering everything and restoring the NAND backup. Do you have any other suggestions? Thanks, by the way. Your videos have been a great help.

[@sthetixofficial]

You can restore your old nand, that is the easiest way to fix the issue.

[@injectx]

@@sthetixofficial Thank you. Do you have more information about the fatal flaw of the FPCB kit?

[@sthetixofficial]

the most common issue is you cannot boot to the ofw

[@DARKSCACKK]

Great job sthetix, I have a modified console (hwfly) after a while the chip was installed it gave me problems when starting: the led was purple at first with slow blinking, then orange and then off or sometimes it was first purple, then orange and it was red. To eliminate this problem, I reset the chip with the corresponding pins, it worked for a while (starting up very fast) but as time went by and without updating the OS or anything, it gave me the same problem as before, currently I have reset the chip and it works super Well, but it seems very strange to me that this is happening to me after approximately a week of use.

[@sthetixofficial]

try to reseat the dat0 adapter

[@aggarwal959]

U always rock!!!

[@sthetixofficial]

Thank you

[@NormanMader-rz8ye]

Hello, which square papel towl / wipes cleaning cloth did you use in the video? I mean these square cleaning cloths from the video, which are pressed onto the board with a brush soaked in isopropanol...

[@sthetixofficial]

It came from a screen protector / tempered glass

[@NormanMader-rz8ye]

We can't buy it individually?

[@sthetixofficial]

I think it is available publicly, the keyword is screen wipes

[@sthetixofficial]

www.aliexpress.com/item/1005003235308406.html?spm=a2g0o.productlist.main.5.5f7340052kQhtp&algo_pvid=a2effa48-dccd-4f5a-a7d1-acf95ab99409&aem_p4p_detail=20230324172429817099646932790010967942&algo_exp_id=a2effa48-dccd-4f5a-a7d1-acf95ab99409-2&pdp_ext_f=%7B%22sku_id%22%3A%2212000024778488410%22%7D&pdp_npi=3%40dis%21USD%218.0%218.0%21%21%21%21%21%402102160416797038690494011d06f3%2112000024778488410%21sea%21ID%21116102529&curPageLogUid=oKkEZpSRI2yk&ad_pvid=20230324172429817099646932790010967942_3&ad_pvid=20230324172429817099646932790010967942_3

[@noble_lime]

Is reflowing necessary?? Because that is the only reason I am not doing this mod

[@sthetixofficial]

no it is not. it tends to cause issues later.

[@NGEvangeliman]

Got an instinct-nx v6 video any time soon? I just randomly ordered one when they dropped to under $40 in price this morning.

[@sthetixofficial]

sooner or later

[@airquis]

@@sthetixofficial is the setup with the instinct the same?

[@sthetixofficial]

same method but they have revised the dat0 adapter, and it is better now

[@hugo8549]

Hey bro, what kind of solder did you use? 0.3mm, 0.5mm, 1mm? Also type lead free solder or lead solder? Cheers

[@sthetixofficial]

0.4mm kester 275 lead free

[@Vannagh1991]

Hi there, I have the Hwfly Oled V5. Is the v5 similar to the v4 you are using in this video?

[@sthetixofficial]

Yes, the concept is still the same.

[@cesarfranku]

Would you do a Picofly installation guide video in the future?

[@sthetixofficial]

maybe if it get a proper form

[@prashkotak]

Hello , sir is that possible if i misplace dat0 and if it touch different point that will burn switch ?, I have burn my switch and some time memory card not detected some time it turns headphone mode on, could you please guide us how to touch exact point

[@chrisguo5698]

4:13 missing one screw under the fan

[@sthetixofficial]

Thank you

[@Izziana]

i liked pcb cleaner. now my favorite is yemyemshee chip

[@papasmurfington5264]

Where can i dependably buy the UL10064 AWG36 Wire? I ordered it from aliexpress -- but they totally screwed up my order and sent me 10 core, 1.6 mm wire! (cheap wire)

[@sthetixofficial]

you need to contact the seller to solve the issue

[@papasmurfington5264]

@@sthetixofficial is there another wire you can suggest?

[@sthetixofficial]

I only suggest using that wire

[@gehnjhosanzoh6902]

hope you a guide in installing picofly in all switchmodels plus software installation

[@sthetixofficial]

No bro. Too dangerous to use as it is improper

[@ozzygalantos8927]

One Question on DAT0 Adapter i cut the Metal shield , but i damaged the one side of ground pads .... any problems with that ?

[@sthetixofficial]

it is fine

[@paoloiaccarino7447]

when you installed the dat0 adapter you soldered the third pin on a capacitor, is that safe?

[@sthetixofficial]

it is safe. it is an additional anchor.

[@cheynespc]

Amazing

[@tongy3334]

About the reed switch part of the video, why is it that the mod kit will occasionally need resetting?

[@sthetixofficial]

because hwfly chips have that annoying bug

[@csl9495]

Why the hell I think I was going to try this... lol. The tools, the soldering skills, the dexterity, the knowledge to troublshoot... for someone with zero experience or know how where do you even begin to start learning? Seriously what project would you recommend that would eventually lead up to the skill set and knkw how to take on hard modding a switch? I want to learn.

[@sthetixofficial]

you need to learn basic soldering and upgrade your skill level by level.

[@Wither_Strike]

how hard would you say this is on a scale of 1-100? getting the new zelda oled in a few weeks and while i personally dont have any experience soldering my brother and dad have some experience with standard soldering of usb cables from our wii

[@sthetixofficial]

better ask someone to do it for you.

[@Wither_Strike]

@@sthetixofficial ah, guess I’ll have to wait for a software hack then. Thanks though!

[@4rt3m]

hi, I followed your manual to install HWFLY (thank you for it!) + added the magnet switch, as you have advised. Now the console boots into hekata only with the magnet attached (otherwise it boots to stock). Is this by design? What can be the problem?

[@sthetixofficial]

your reed switch is NC (normally close) i guess, not NO (normally open). remove the reed switch and check it out

[@Danjovisagat]

Oh my days! The sdcard reader is attached to a board, finally! I broke 4 nintendo switches due to breaking the sd port its way too fragile.

[@mohammedaltameemi5342]

Thank you very much. And is it possible to make a video for the switch lite

[@sthetixofficial]

it is there, odysee.com/@sthetixofficial:9

[@quajay187]

instead of cutting the traces under DAT0, could you just put a piece of kapton tape instead?

[@sthetixofficial]

u can . there are many ways to do the same effect

[@Tuanngoc109]

Please help. My hwfly v5 switch can boot to emunand but it can't boot to ofw (blank screen). You explained using fly wires instead fpcb in this video but replacement samsung mmc method in ur another video. So if I remove fpcb and using flywires do I need also replace samsung mmc to boot up ofw? I have hynix mmc

[@sthetixofficial]

samsung has no issue with the fpcb but you can try removing the kit and see.

[@heavyknight6117]

I have a question, this tutorial can be used on a normal swich? It's because I want to mod mine to put smash mods but I can't do it normally because it's the super smash bros ultimate special edition of the swich. (Sorry for my bad english).

[@sthetixofficial]

This is for oled

[@doniherald7745]

Cutting those traces for dat0 adapter is unecessary and demaging, if that point could make short then just cover it with uv mask.

[@sthetixofficial]

there are many ways to do the same effect. I dont use it anymore because the dat0 adapter is now perfect.

[@MattDeezly]

Do you have to use 36AWG wire? I can't find any anywhere. I found the modchip easier

[@sthetixofficial]

it is on aliexpressx,. they keyword is UL10064 AWG36

[@14vo7]

he tried so hard to not get killed by big n

[@hamidmohammad5097]

What is the difference between hwfly and picofly and which is better?

[@sthetixofficial]

pico does not have a real fpga while the hwfly has. Not only that, the PICO has many variants, we don't know which one is the best.

[@AgentJeffy]

What was the issue with the flex cable versus running individual wires?

[@sthetixofficial]

it wont boot OFW or sysmmc CFW if the emmc brand is hynix.

[@hopechannelhopemusic]

This SD card doesn't work with instinct v6s

[@sthetixofficial]

try other sd card brands, like sandisk.

[@raphaelwestphal1429]

After doing the installation I get a white led, any idea what could be the reason ? I double checked the CPU connection and it seems fine Also I see that we don't ground the board in the tutorial, is it not risky ?

[@sthetixofficial]

led white means something is lose. recheck the soldering

[@GlitchyKnoppix]

Do you offer installation services?

[@sthetixofficial]

I do, but locally, because I am in Indonesia. Sending the tablet to me is not cost effective.

[@sergiochendry4766]

Mau tny nie min Untuk jalur groundnya di video ini tidak di solder ya? atau krn groundnya udh digantikan oleh magnetic reed?

[@sthetixofficial]

Bukan. Tapi sudah ada di flex cpu ribbon cable

[@sergiochendry4766]

@@sthetixofficial ok thx min

[@추앙-d6q]

May I know which point I should solder to install MAGNETIC REED SWITCH on v6 chip?

[@sthetixofficial]

no reset feature on the v6. you need to use putty to reset the chip

[@davidsii5822]

can u teach me how to update the firmware of instinct chip? and how to reset w/o the magnetic thing? thx in advance

[@sthetixofficial]

you better watch my putty guide. there is no new firmware for the v6

[@tecnicoemeletronica]

hello can you tell me what is this yarn you use and where can i buy it? thanks

[@sthetixofficial]

wire? it is on aliexpress, UL10064 AWG36

[@RisingStarL96A1]

the C point that we connect from the dat0 is to the c point on the chip?

[@sthetixofficial]

yes

[@karmachameleon3268]

Can you please tell me what the Dat0 connection is actually used for during the glitch process? I‘d like to understand how crucial the connection on that point is since you do not solder it.

[@sthetixofficial]

it is needed for the modchip to glitch the console. if you want to know technically, you need to ask it on the GBAtemp. DAT0 = Data Signal 0

[@karmachameleon3268]

@@sthetixofficial Thank you very much for your answer. Do you think the connection will last in a long term without soldering it? I‘m struggling a bit in that concern.

[@sthetixofficial]

it depends, every method has its own issue. even with reballing, it could crack. it is still a mystery.

[@airquis]

@@sthetixofficial are the ones you did from November still working?

[@sthetixofficial]

yes most of them works

[@cheezyfriez12]

Where can i buy one of these? And can it be installed on a pre OLED console (launch or lite models)

[@sthetixofficial]

the kit? you can buy it on aliexpress. you can install it on Lite, V2 and OLED

[@cheezyfriez12]

@@sthetixofficial awesome. Normally I'd ask for a link but with the dicey situation surrounding these modchips I'd rather just hunt for it myself. Thanks for confirming that btw.

[@adsmodshop]

What happened to Ground point? How is the chip working without Ground?

[@sthetixofficial]

It does not , but FYI, the GND signal is included inside the Flex cable

[@prashkotak]

Hello sir, could you please make video for 2023 Newest Hwfly Oled V4.3,V4.3+ Chip, Full Set Support Oled Console Upgradable and Flashable , components are changed here

[@sthetixofficial]

no. just watch the v6 video

[@LatifKarakoyun]

why don't we use solder at 7:45?

[@sthetixofficial]

I've explained it in the video

[@onefloofysheep]

I have not installed the dat0 adapter, I booted everything and it is flashing yellow then magenta and red, if I install the dat0 adapter everything will be alright? (I will only be able to install the dat0 next week as I ruined the adapter as I pulled off the bonding pad by accident)

[@sthetixofficial]

you need to install the dat0 - why did you skip it?

[@onefloofysheep]

@@sthetixofficial I ruined the adapter :/ also just to check are there any alt d points?

[@sthetixofficial]

u can remove the adapter and reball the emmc

[@onefloofysheep]

@sthetix oh probably not I just ordered another emmc adapter haha I'm only 18 I dare not do such a thing

[@MintPeppers]

How come you didn’t have to wire up the ground pad on the chip?

[@sthetixofficial]

Because the flex cpu have those gnd signals

[@MintPeppers]

@@sthetixofficial Makes sense. Thanks!

[@추앙-d6q]

may i have some information about magnetic reed switch?

[@추앙-d6q]

sorry. in vedio gps-11a ty

[@kozakalex222222]

22:56 - m

[@compitalc]

m lol

[@sthetixofficial]

Argh..sorry for the typo hahahaha

[@MizuhoChan]

What sort of flaw does the fpcb kit have that prevents stock firmware from booting? I think this is the issue I'm having, but I can't find any information on it.

[@sthetixofficial]

it has a 3.3V interference issue.

[@MizuhoChan]

@@sthetixofficial I see, I'm not sure if that was my issue now, as I removed it, but accidentally knocked off the 4.5k resistor for point A, so I had to replace it with an 0603, since that's all I had. That fixed my issue though, so one of those two.

[@jaellkenniegaming7292]

Which is better HWFLY or inStinct Nx?

[@sthetixofficial]

both have the same goals and each chip has its pros and cons

[@ailoveu806]

Hi bro, been following your guides since the 3ds days. I just want to ask. I accidentally updated my OFW again online(I just press A without reading) but I notice that on both updates, my chip would always have a blue and pink light and it will boot straight to OFW. What could be the problem here? OLED user btw

[@sthetixofficial]

You need to reset the chip

[@ailoveu806]

@@sthetixofficial Ahhh I see. And to reset the chip, I just have to short the 2 pins right?

[@sthetixofficial]

Yes

[@ailoveu806]

Cool! thanks bro!

[@08z33tt]

I have the same problem. I tries shorting the 2 pins but it won't retrain. Any advice?

[@KarimErrytouny]

When is the Picofly tutorial coming?

[@sthetixofficial]

i dont support it until it has a proper form.

[@mostafajento]

How to use the GPS-11A ?

[@sthetixofficial]

it is a reed switch, just connect one end to the gnd and one end to the reset pin that is not gnd

[@DaRkBlooD24100]

Is there any chance that you will also do picofly mod for oled switch?

[@sthetixofficial]

Not for now.. Pico is dangerous and improper

[@itzSamito]

Hey, could you make s tutorial on how to swap a modded NS mother board to a new one, And what will happen after that? thanks in advance! 💙

[@sthetixofficial]

It is like disassembling and re assembing. No special tricks.

[@34disorder84]

Ya'll think if i got the modkit and went with it and my switch to some local phone repair shop and gave them this tutorial, would they do it for me? 🤔

[@sthetixofficial]

yes as long as they can follow the guide.

[@jcalm1]

I see people been bridging the resistors for the 3.3V connection. Is it normal?

[@sthetixofficial]

I don't know about it

[@rostomzerrougui]

Can you provide us where can we buy the 256gb nand to do the upgrade please?

[@sthetixofficial]

on the aliexpress : www.aliexpress.com/item/33002787553.html?spm=a2g0o.order_list.order_list_main.5.3be618022JjSaI

[@Blaketoob]

When i install the hats pack it says read only and I can't transfer the files.

[@sthetixofficial]

Your SD card is locked probably, try to replace it

[@skree25]

Where can i purchase Switch chips/parts for repairs?

[@sthetixofficial]

On aliexpress

[@ACMEsabers]

You are an absolute legend! I probably increased the view count on this video buy a few hundred😂 I'm very comfortable with my soldering skills and have done smd components multiple times in the past, but this was a whole new level. I wouldn't have been able to do this without your help 🫡🫡🫡 Thank you so much.

[@sthetixofficial]

you are welcome.

[@artgamecell]

why cut the lines in nand ?

[@sthetixofficial]

that is not the nand

[@joshuamartins647]

Is the guide thr same for a normal switch

[@sthetixofficial]

it is different

[@joshuamartins647]

@@sthetixofficial where can I find a guide of a v2

[@sthetixofficial]

its on odysee.com/@sthetixofficial:9