Wow fantastic work....incredible..I don't know where else to go on this on...WoW
@davidhotchkiss89229 ай бұрын
Amazing work as always Dan. I learn so much from watching your videos. You helped me get over my fears of using powders and weathering cars as a whole. I began weathering cars a couple years ago, as a way to keep my hands and mind busy. I have had 58 surgeries and 6 TIA mini strokes, so it's important. It's like a therapy. I get along OK now, after lots of PT and mental stamina. I just cannot work anymore. I always look forward to your next project! Thanks again!
@michaelsmodelrailroading76659 ай бұрын
*** WOW!! *** What an extremely authentic looking weathering job! Especially the carbody sag and beat up panels. Your finished model reflects years of abuse and service. Thanks for sharing your process and techniques, which produce exceptional looking results.
@DavidinSLO9 ай бұрын
The biggest difference with model railroading in the USA verses Europe is that Americans tend to go with a VERY weathered, lived in, and gritty look and feel on everything from the trains, to the cities and towns. This is certainly an excellent example.
@vikingofengland9 ай бұрын
I am from the UK but love a filthy gondola over clean ones any day of the week ❤
@douglasskaalrud68659 ай бұрын
I’m an American modeling present day conditions and I find cars weathered to this degree are very scarce unless you’re into mill towns with whole trains of these decrepit cars. And rust? Thanks to modern coatings like urethane and epoxy, rolling stock inside of ten to fifteen years old will only have marginal rust. And if all cities are as overwhelmingly gritty and bad as you think then nobody would move there, would they? I think modelers have gone off the deep end and have acquired the Joh Allen syndrome, which was unrealistic then and even more so now. Doesn’t mean we can’t enjoy creating cars like this but I challenge anyone to, outside of the rust belt, find trains with more than a few cars anywhere near as bad as this.
@beeble20033 ай бұрын
@@douglasskaalrud6865 "I find cars weathered to this degree are very scarce" Really? I'm in the UK, but I watch a lot of videos of American railroads on KZbin and cars in this state seem pretty common to me. "And rust? Thanks to modern coatings like urethane and epoxy, rolling stock inside of ten to fifteen years old will only have marginal rust" OK but the car Dan's modeling here was built over 40 years ago and there are plenty of cars of that age around the network. "And if all cities are as overwhelmingly gritty and bad as you think then nobody would move there, would they?" Railroads generally serve industrial areas, which aren't the nicest part of town. Even the most beautiful town has its dodgy areas, and that's where the railroad is more likely to be. So there's no contradiction in modelers depicting things as less nice than the average town.
@beeble20033 ай бұрын
I think the difference is that European railways are mostly passenger-focused, which keeps things a lot tidier.
@michaelricks16189 ай бұрын
Another fabulous model, Dan, Thanks for all the great tips!
@edduke85279 ай бұрын
Absolutely beautiful Dan. I would love to have one of your models on my layout!!!!
@streetfightinmanrs9 ай бұрын
I love this. Taking old roundhouse cars and updating them with custom detail parts is something that I am trying to emulate with a block of 10 or so of the same cars (RailGon GONX 310160 - GONX 310169).
@thomasmccaskill51979 ай бұрын
Awesome job as always Dan and a great tip on warping the gon
@UnionPacific1943-hz2oc9 ай бұрын
I like that nice weathering on the gondola i would do the same thing for my gondola 😁👍
@jimnicholas76669 ай бұрын
Excellent work as always!!
@bradfordgordon65529 ай бұрын
Great job Dan. You always put a lot of effort into your stuff. I one recommendation that should of been done on side ends where the two handrails are with the stirup. I would of took the small handrails off then put the warped styrene on. You could of redrilled the holes to put the handrails back on. Great job though. Thanks
@ronaldrondeau78709 ай бұрын
great job again
@edduke85279 ай бұрын
Absolutely gorgeous!!!! Would love to have one of your models on my layout!!!!!!
@RFMCabooseNP17139 ай бұрын
Man you do great work.
@stephenhottle67839 ай бұрын
Very nice 👌
@NSWLE9 ай бұрын
All I can say is,,,,,great job!!!!
@JosephMusgrove9 ай бұрын
Nicely done!
@Grainexpress9 ай бұрын
Another Emmy award winning video Dan! Just looks golden! One question is when you painted the sides I assume you masked off the yellow paint?
@beeble20033 ай бұрын
My guess is that he was just careful -- small amounts of "painting outside the lines" would just look like rust on the edge of the yellow section, which is what he wants anyway.
@Shaken_AND_Stirred9 ай бұрын
Thumbnail looks like a real car.
@Benton-SouthernRR9 ай бұрын
Fantastic weathering! Love the sagging effect. One quick question... when you warp and sag the car, does it affect the coupler height and how do you compensate for that if it does? Thanks, Brian
@glenfrix1579 ай бұрын
and do the trucks ride correctly on the rails? I guess you can put the screw in a bit less tight to solve?
@whiteknightcat9 ай бұрын
I had a similar question - if the body is warped, how was the underframe mounted back on? Was it forced to warp via the truck screws or cemented in place?
@DansRailroad20119 ай бұрын
@@whiteknightcat To answer for everybody, you will need to shim the coupler pockets with .010'' styrene. As for the trucks, I will add a little 010'' styrene shim to the carbody around the mounting so the truck sits corrected at a flat angle.
@whiteknightcat9 ай бұрын
@@DansRailroad2011 Thank you
@NicholassTrainChannel9 ай бұрын
Nice video Dan. The weathering came out great. The warping effect came out great too. My only concern with that is does it affect the running performance of the wagon and also coupler height?
@beeble20033 ай бұрын
I doubt it affects coupler height very much. The ends of the car are bent slightly upwards, but it's only the short distance between the truck pivot and the end of the car that's raising the coupler. Likewise, I doubt it has any significant affect on ride: the pivot screws aren't quite vertical after the bending, but they're very close.
@tomoconnell42359 ай бұрын
Excellent
@thomream18889 ай бұрын
Hi Dan - have you considered using .005 brass for embossing the sides? I made my side panels the same way, just using sheet brass (Hobby Lobby. Michaels, etc). I then used double-sided tape to hold them down while I dropped a variety of metal objects (nuts, screws, even wooden dowels) and achieved a really cool effect. I used CA to glue them onto the gon sides. Man, I wish I had your eyesight! And maybe a tenth of your skills. Keep it up brother!
@beeble20033 ай бұрын
Brass is more expensive, harder to work with and harder to attach to the car. What advantages does it have to outweigh that?
@IowaGrandpaTrain9 ай бұрын
Questions: How do you remove the original chord and what do you replace it with? How do you attach the floor and do you modify it in any way? What about coupler height? If you bow the entire body the couplers will point upward and coupler height will be wrong. How do you fix this?
@DansRailroad20119 ай бұрын
I don't remove the original cord, I simply add styrene L channel on top of it. The floor is simply glued in place with superglue, and I've never had issues with them not fitting after this technique is done! Coupler height is adjusted with styrene shims.
@centeroftheearthmining40959 ай бұрын
Fantastic!!!!!!!!!
@DirtyDan490-t2vАй бұрын
How did you secure the distressed panels to the car? I'm assuming CA or some sort of super glue
@DansRailroad2011Ай бұрын
CA indeed! You can use plastic cement as well but with thinner styrene, it can melt the panel so you need to be careful!
@Justfor1day9 ай бұрын
🏆🍻
@alanbrandon829 ай бұрын
When you sell on Ebay what's the name of your account ?
@randydobson18639 ай бұрын
hello DansRailroad2011& it's is Randy and i like yours video is cool & Thanks DansRailroad2011 & Friends Randy