Modifying or Improving Thermals on KS0 Pro, Ultra, AL0, & RX0

[@SerpentXTech]

Go 1.5mm on thermal pads, per recommendation.

[@D1g1tal_H1ppy]

thanks homie. great instructional!

[@davidkconcrete]

Thank you. Will be very helpful when my stuff gets in this Friday to do this on my 2

[@K-A_Z_A-K_S_URALA]

ПРИВЕТ ПОДСКАЖИ КУДА ДУЮТ ВЕНТИЛЯТОРЫ ТВОИ ?

[@jkw75]

Great video as always, where can I get the type of heatsink that you used?

[@ZenTauren]

What is the highest OC without mosfet cooling? 260GH/s?

[@TycenYT]

Did customs and duties charge you? how much do u know?

[@SerpentXTech]

I didn't get charged anything else, but I think it was priced in to the overall price paid. Shipped from Asia

[@rtweeg]

Hello, I would like to clarify a doubt about the dimensions of the heat sinks you used. Could you confirm whether the model used was 3.5cm x 3.5cm and 3cm (or millimeters) in height, or if it was 6.5cm x 6.5cm with 12cm (or millimeters) in height?

[@SerpentXTech]

6.5 in height and 3mm L & W

[@AlteredComponent]

good video buddy. curious though, in the 2 temps screenshots you added at end of this video, The temps were way better on the after. Was that simply just the mosfet heat sync, thermal repaste, and the thermal pad replacement? I may do this to my 2 pros, but just going to try and run the 280 firmware and not the crazy 360. Keep grinding

[@SerpentXTech]

Thermal paste Kryonaut Extreme, and stock thermal pads. I was supposed the replace it but I thought just like GDDR6X, if I can draw most of the heat out the front of the chip into the main heatsink I could save on thermals.

[@AlteredComponent]

@SerpentXTech well done buddy. I dig it. I just finished thermal testing a stock kso pro with different orientations and fans. I have the tswift firmware already, just haven't installed yet

[@SerpentXTech]

@@AlteredComponent 340 video next Wed. And issues I bumped into even with mods

[@trailerminer9650]

Are you running the stock PSU with the higher ghs firmware

[@SerpentXTech]

No 230w MSI psu

[@SerpentXTech]

amzn.to/3wwHs3i On one and then tis on the other theveteranminer.com/product/barrel-connector-to-12volt-psu-6-pin-pcie-female-for-ks0-asic-miner/

[@trailerminer9650]

@@SerpentXTech thank you just ordered one I did see somebody mentioned in another video that this is what they were using and wasn't sure thank you thank you

[@fahadKG]

what's the link for the heatsinks? thanks

[@SerpentXTech]

MOSFET heatsinks small: amzn.to/3UdQ4Wp MOSFET heatsinks Big: amzn.to/3OfNmvV Thermal Paste and Pads: amzn.to/3u4WvR4 amzn.to/3u4WAnQ

[@LunchBoxMining]

How is it running ??

[@SerpentXTech]

Good, but I am hitting 340 Ghs on the 320L version, another video is scheduled next week for that update, and what I found

[@trailerminer9650]

Apparently all that size copper heat sinks are being bought up

[@SerpentXTech]

amzn.to/3V18iej

[@SerpentXTech]

amzn.to/3uUHJN0

[@trailerminer9650]

@@SerpentXTech I just ordered some straight from China that's where it all comes from anyways

[@trailerminer9650]

@@SerpentXTech I figured it out somehow my Amazon got switched to another Nation I think I was looking for items that were listed somewhere else

[@horstMay-rs5oe]

Your copper pin cooling at its best, only aluminum and thermal adhesive >10W/m*K, everything pressed on.