Replace R53 MINI Cooper Throttle Body P1125 P1126 P0638 2002-2006

[@ModMINI]

You might need to replace your 2002-2006 MINI Cooper R53 Throttle body if you get a check engine light/limp home mode. Procedure similar for non-supercharged R50. Buy the throttle body here: ebay.to/2UQJbvW Pinch clip tool: amzn.to/2IfN2wN Diagnostic tools that can reset throttle body adaptation: amzn.to/2IeqXyu amzn.to/2VFEYs0 amzn.to/2UySnWo

[@bobrichards3841]

Thanks for this video, and the others, top advice !!

[@VMCJR0NE]

Thanks for doing this video I replaced mine on an 06 S I have but I never did the reset on the throttle body it worked fine but later on couple of weeks later I got codes and I the rpms where where going up and down then the car would go on li.p mode and give me a code 1498 and 1125 I did replaced a broken hose and also the bypass valve for the supercharger with anew gasket and still gave the code and would idle up and down. I just bought another new throttle body and the BMW tool the 360+ but it won't connect the the throttle body to clear the adaptation. It only comes to read it but not to clear it. Right now it's working fine what would happen if I can't clear the adaptation! I ha e no more air leaks it's driving me crazy. Can you help. Me!

[@SAK1974-f9o]

Hi, I've got a 2006 mini cooper s model , with a fluttering acceleration from 1st to 2nd and a little to 3rd. Keeps giving me a cylinder#2 misfire. I've tried all the small repairs... Any known issues that will cause this? When it gets up to speed, it drives fine, but only when loaded in 1st gear does it five an issue.

[@ModMINI]

@@SAK1974-f9o Compression test and leakdown test to verify the cylinder compression is good.

[@SAK1974-f9o]

@@ModMINI Thanks so much for the response. Thanks for all the videos you've done on Minis, it has help a whole lot.

[@markcunningham8142]

Thanks for helping me keep my R52S running. I could never afford it if not for your help with the videos.

[@bvcxzgt5451]

I'm so glad to see a Mod Mini solution. Thanks for making these cars easy to own.

[@mokacat1595]

4 years ago I had the exactly same symptoms with my old min cooper base CVT that nobody couldn't figure out and wasn't worth taking the mini to the dealership so I sold the car as-is.. funny today I found out what was causing the issue. thanks for the videos!

[@honestreviewer3283]

This channel is a lifesaver. I put a R53 throttle body on my R50 (along with a bunch of other mods).

[@frankgualtieri3966]

Thanks for saving me again brother ,this is exactly what my car is doing ! Appreciate your videos

[@MakerOnTheMove]

I bought the first diagnostic tool you link to (Foxwell NT510). Unfortunately it cannot reset the throttle body adaptation on an R53. I contacted Foxwell, and they told me I 'd have to get the NT530. Just a heads up.

[@MrSociallyDistrted]

Did you get the proper Foxwell tool and reset adaptations on your R53?

[@alfredvalrie5541]

You should make a “Hi, Everybody” shirt.

[@ModMINI]

Haha. Any paying customers for this?

[@alanaugustine8565]

Just had mine replaced yesterday, unfortunately I had to pay crazy money to get it done. Definitely a DYI fix.

[@bvcxzgt5451]

DYI? Is that what happens when you try to fix it yourself but break additional stuff in the process? Do Yourself In fix? I've done that.

[@jeromea1659]

@@bvcxzgt5451 😅 if you've ever worked on a 15 year old BMW🤣 it kinda does you IN for the parts that exist in the immediate vicinity of that One you want to replace. Need 1 part buy 3😡🤬😂

[@reinier1234]

Resetting the throttle adaptations is same as throttle relearn ? I replaced my throttle body and throttle pedal, but didn’t do the relearn and after certain time it goes to limp mode p1125 code

[@Yetterben]

Another classic. That fancy intro you guys made for that one video was boss. You should use it more.

[@ModMINI]

I still need him to give me the clean intro so I can add to more videos.

[@BradHawthorn12]

Great video. Good audio quality and explanation. Very helpful. Thanks!

[@ekmetaldetecting9768]

WHAT COLOR IS THAT CAR LOOKS AMAZING

[@junkpile936]

Thanks for your great videos, very informative and easy to follow. What I have going is intermittent limp mode with codes of P1125, and P1229. How can I diagnosis the difference between problems with throttle body or bypass valve. I don't want to just replace parts if not needed. Thanks for your time in response.

[@REMOtor_]

I got the 3 code you mentioned in the video.After I replace the Tb do I need to something?

[@robbiethompson8297]

I have a mini cooper s r53 gtt230, and only get full boost if i disconnect the bypass valve, i think i need to replace it? Any feed back, will be fantastic Thank you

[@harryhopless]

While i have my throttle body off my 2002 mini cooper s is it ok to open the butterfly for a better clean... reason asking because with my lpg ford its not a good idea...Ps your videos are the best to watch...

[@ModMINI]

Should be ok, reset with BMW scanner if anything happens, but it should do a self-calibration every time car turned on

[@serenitybase9888]

great videos, which one is the Throttle Plug?i have error code 1682, and the mechanic said to unplug and re plug the throttle body plug? thank you jeff

[@drocknden]

will this cause a lack of pressure in the fuel rail?

[@alconk7129]

Could you please talk about the light strip above the dash. That is so cool and would love to install one on mine. Thanks!

[@ModMINI]

Not my car. The owner installed an LED strip in the gap between the dashboard cover and the dashboard.

[@More2Historythantaught]

Where does the tube connect to off the side of the throttle body ?

[@ElChris86]

Great video!!! Can you tell me what’s going on with my car. Got this codes P11AA, P169F, P173B i have 2012 Mini Cooper S automatic

[@alfredbernal8603]

Hi Mod Mini! Just had a P1125 code appear on my 2006 mini cooper. I cleared out the code with my cen-tech. Should i wait till the code appears again or should i change out the throttle body now? Already performed a tune up.

[@nagoyaboya]

Great video. I thought I was having throttle body issues, but I'm getting the codes: P0302, P0456, P0300, P0313 as well as an evap leak on my R53. I have new spark plugs installed, checked my gas tank cap, but at this point can I assume its a MAP sensor issue? Do you have a MAP cleaning video? Thanks!

[@ModMINI]

That's a lot of codes, some of which can point you in the wrong direction without some critical thinking. I'd unfortunately have to look at the car to comment further.

[@minimanadam]

You can do a throttle reset ( throttle relearn procedure) just by depressing the gas pedal with key in acc power mode for 30seconds, turn off key WHILE still depressing pedal and remove the key and then release the gas pedal. You SHOULD hear your throttlebody actuate ( a buzz noise followed by a click kinda sound ).

[@alfredbernal8603]

Hi Adam..what year is your mini? I have a 2006 mini cooper s and i am wondering if this method will work for my car

[@mikeoconnell9611]

Quick question.... my 2003 MCS (with 193,000 mi and manual transmission) had an accelerator pedal non-response yesterday. No codes, no engine light, no rough idle, nothing. Just went to a smooth idle with no pedal response. First time anything like that has ever happened. I pulled off the road, turned off the ignition and popped the hood for a quick visual. Got back in the car and restarted it and everything was fine for the ride home. My thoughts today are that the throttle body is telling me that it's probably time to replace it. Looks like a fairly simple procedure thanks to your video. Have you ever heard of such a situation that didn't produce and engine light/code? Thanks, Mike

[@alfredbernal8603]

Hi Mike Did you happen to change your throttle body? Did it fix your situation?

[@mikeoconnell9611]

@@alfredbernal8603 - Hi Alfred, sorry for the delay. Unfortunately, I donated the ‘03 MCS to “Cars for Change” late last year. I never did get around to replacing the throttle body and the event only ever happened once. I was a rough call to part with the ‘03, but it was rapidly approaching 200k, and it had a few other things I just really didn’t feel like fixing. I still have my ‘06 MCS convertible, my ‘08 MCS hatchback, and my ‘14 S Countryman. So lots of Mini’s still around for me to motor with. Take care friend, and happy motoring!

[@alfredbernal8603]

@@mikeoconnell9611 Hi Mike! I appreciate your response. We have two 2006 mini coopers ourselves. The problem that we are encountering is perhaps the throttle itself. Car sometimes goes into limp mode with a check engine light for the past 6 months. So we turn it off and turn back on successfully, check engine light goes off. We once checked it with my scanner showing a 1125 code. I am suspecting it could be the throttle body based on these symptoms

[@simonkong7205]

Hi Mod Mini! Thank you for all the helpful videos! My R53 has a P2127 code Throttle/Pedal Position Sensor/Switch E Circuit Low. I have check engine light and/limp home mode...Is the sensor different from throttle body? I can't seem to find parts for throttle position sensor. Thank you for any guidance you can provide!

[@simonkong7205]

I changed the throttle body and it fixed my issue. Thank you Mob Mini.

[@alfredbernal8603]

@@simonkong7205 Hello Simon..having an issue with my mini and i believe my throttle body is the problem. Car goes into limp mode with a check engine light. I turn it off and goes back on with check engine light off. Thinking of changing out the throttle body..already cleaned it but i believe it is the electrical of the throttle body is the issue. What brand throttle body did you get?

[@95turbostang21]

Hello I just bought a 2005 Mini Cooper automatic for my son and we are having a problem when we start the car it will start out fine Rev fine the moment we put it in Drive the car has a vibration feel with low RPM and no throttle response whatsoever any ideas that you can think of? There is a service engine light but I have not purchased a scanner yet I know that would be the best place to start with scanning it I'm just curious if Mini Coopers are known for this type of issue and if there is anything you can think of off the top of your head

[@mistacarp6533]

My R53 feels like it has a lazy throttle body, when I lift off the throttle during gear change the revs stay high for a second or so, have you ever come across this? Would really appreciate your help.

[@ModMINI]

R53 is known to do this. Probably nothing to worry.

[@bvcxzgt5451]

@@ModMINI Confirmed. Mine has done this since new.

[@raymondrizzuto7997]

I had codes that indicated the throttle body, but the car ran fine. The prior owner replaced the throttle body 2 months ago (I have his receipts). I reset the codes (P1125, P0638, P1126, P1229) and waited. Several days of running fine, the it started rought and stalled twice, but ran fine on the third try. Again, the engine light came on, with codes this time P1125 and P1229. I made an appointment at a local independent shop that got good reviews. The shop diagnosed the issue as the engine wiring harness. The harness is $400, labor is $700, plus $100 for programming. What's your opinion about the diagnosis and the possibility for a DIYer to do this?

[@ModMINI]

I can't comment on a diagnosis without seeing car myself. Changing the wiring harness requires no special tools; I don't know your skill level so I can't say whether it is possible for YOU to do this job or not. Programming is just clearing codes and resetting throttle adaptations. which can be done with this tool. amzn.to/2IhCfkk

[@raymondrizzuto7997]

Thanks for the reply. I was able to replace brakes, rotors, 1 caliper, and power steering hosed by myself. How would you rate the wiring harness replacement compared to those? Before I decide to replace the harness, I hope to check out the wires as best I can to see if there is a spot that shows damage from abrasion. If I see that, I may be able to repair the current harness. I'm very comfortable with soldering and heat shrinking.

[@iserved1642]

@@ModMINI Can you perform this step without messing up an aftermarket tune?

[@ModMINI]

@@iserved1642 Clearing adaptations will not affect a tune.

[@raymondrizzuto7997]

@@ModMINI Since the wiring harness is a lot of work, and seems the least likely to be the issue I decided to replace the throttle body first. After ~100 miles, the symptoms returned. I then pulled the ECU to send it out for rebuild, but before I did that I noticed a bent pin on one connector that would cause the pin to not go into the socket properly, possibly making slight contact. I straitened the pin and have driven over 300 miles without issues. If I get to 500, I will assume that was the issue.

[@avefenix1339]

Question! I have the check engine light on after putting the AC and was told that the hose that goes to the throttle body was loose. Now the light is off after driving the car for a little while. Not sure if I might have to fix the throttle body part too. It has stopped responding to switch gear again and did not had the air on.

[@ModMINI]

If car is not put together correctly, you will have problems.

[@AutoResponder-l1k]

What it could be if only P0638 error appears? Thanks

[@AutoResponder-l1k]

Same for me, turning on the car the idle is ok, then it goes in protection if I accelerate over 3k rpm/min alerting P0638 error only, then the idle engine become strange until i turn off, thanks

[@8lackWolf1982]

Hello I Bought the 310+ to reset the adaption of the TB. But the Diagnose always says to me there is no connection. Everything else works. Car drives good as well. Any suggestions? Thx

[@randelldanner8588]

Question? When the throttle body starts going bad what kind of sound if any does it make. I have this whirring/humming sound and goes a few seconds powering down when I turn the car off

[@ModMINI]

It will throw codes when it goes bad. Noise after shutoff is normal.

[@brianhaygood183]

When looking at scan tools, how do we know which ones do throttle body adaptation? I see your list of three, but owners of those are mentioning others they like better, like the Autophix 7810.

[@ModMINI]

Really hard to get detailed information like that. Even manufacture is unlikely to know for sure due to continual changes in software. I think that is only supported on most expensive tools.

[@brianhaygood183]

@@ModMINI a friend tried a SnapOn Verus Pro and couldn't find it. Thanks.

[@anderssonenriqueardilaardi4266]

Hello Mate, I have the same codes, but I replace the TB 10k Km before. this codes appear again, any recommendation? I need to replace again the TB? or I need to reset the codes from the ECU or something like that? Thakns!

[@RealOldRob]

What is the vacuum line/hose that you disconnected from the throttle body? Mine looked really old and cracked last time I worked on the car so I'd like to order a new one to replace it, but am away from my car for a while so I am unable to look under the hood to trace it.

[@ModMINI]

crankcase recirculation. Look up realoem.com for part numbers, although that one you could probably use equivalent diameter fuel line.

[@RealOldRob]

@@ModMINI I think I'll try the fuel line idea and just replace the rubber section. Cheaper than getting a whole MINI hose. Thanks for the tip.

[@joecaires5735]

2003 Mini Cooper S antifreeze Wells inside the reservoir replaced water pump thermostat and radiator still happens what do you think is the problem

[@ModMINI]

Test the coolant for presence of exhaust gas to rule out blown head gasket

[@kylehollinsworth]

p1692 it's that also a replacement code?

[@cirquedumike]

I tried this with 2 different "aftermarket" throttle bodies. Didnt work. Do u prefer OEM genuine parts?

[@denniscook3484]

I keep getting a p1239 ive pretty much replaced everything i can think of and still wont go away. Any help would be much appreciated

[@aurora9636]

I replaced mine and car giving me an evap leak code. What could it be? I made sure to tighten everything right. Nothings loose.

[@vmpns]

hi, I wanted to ask you my problem, I have a Cooper s R53 and for two years I have the following error codes P2122 P2123. replacing the accelerator pedal, the problem reappeared after months, and then disappeared for other months, now it becomes more frequent. I will change the trottle body soon. but on the forums we read that the problem may persist ... the fault of the ECU! ?? Thank u

[@bvcxzgt5451]

What ended up happening? Recalibrating the throttle pedal can be done easily. I forget the procedure exactly, but it may just have been holding the pedal down while turning the key to "on" (not starting the engine), and keeping the pedal down for thirty seconds, then release the pedal and turn the key off. I had to do that after replacing my pedal. 6 months later all has been well until today when I get P1125 and P1129, so I'm ordering a throttle body, I guess.

[@jjcc2785]

Hello mod mini, i have my mini Cooper r52 cabriolet 2005 that is giving me some issues. First of all has a long cranck to start ( like 3 or more seconds) then irregular idle and the engine has not all power and not fast response of the engine when I touch the throttle pedal, plus engine check light on and the error my mechanic said is about missfires and too rich gasoline mix. I changed air filter, sparkplugs and body throttle cleaned and resetted but the problem persists. My mechanic said that I should replace the body throttle, but can't be the depression hose or pedal sensor? The car has 190.000km what do you think about? Do you suggest an original one in case or a Siemens ? Thanks

[@derekkchung]

Is it possible to take apart the throttle body to clean / rebuild? I know it is bad. I will take it out first. If I can rebuild it, I don't have to wait for the replacement.

[@ModMINI]

I wouldn't risk my life on such an endeavor.

[@maurodenisleon4691]

Really liked your video. I have a question. What could be causing me to have a check eng light and EML light ? I hooked up a scanner and got code: P1498 Air leakage after compressor. Could it be the intercooler boots? I have. 06 R53 S with 74,000 miles. Thanks for time.

[@ModMINI]

I'd guess you have air leakage after compressor. Do a smoke test.

[@jaypark5952]

hello Mod MINI, thank you for the great video again! many of your videos were HUGE help with replacing supercharger on my 2005 cooper S. may i ask a question? Have you ever encountered P2127 Throttle/Pedal Position Sensor/Switch "E" Circuit Low? I searched everywhere but no help on any web or forums? replaced gas pedal (used one) and removed/cleaned throttle body but still getting the same code.... any help would be GREATLY appreciated. thank you! Jay

[@ModMINI]

Try replacing that perhaps. Used ones aren't expensive

[@bvcxzgt5451]

I got that code, replaced my pedal with a used one, and still had trouble until I recalibrated the throttle pedal. Easy DIY recalibration. Look it up online, but my recollection is pedal held down, key on, hold pedal down 30 seconds, release pedal, key off.

[@GuyOntheroad-wf7tf]

Hi, my 2006 manual mini turns off when i put it in reverse, do you know what could cause that?

[@dkterra1]

Do you recommend the seimens brand that comes up first?

[@ModMINI]

Seimens is OEM so yes.

[@RAM77511]

02 Mini Cooper S Could it be possible that a TB when going bad trigger the EML to come on? I was on the freeway today and car shut off then when started back up EML light came on.

[@ModMINI]

Yes, but read the codes. You need codes or you're blind.

[@hippyboi1992]

Hi MOD MINI videos are great recently replaced BPV and serviced supercharger. My Mini cooper s 03 plate is still throwing a fault p1125 and going into limp mode, I can restart and it will be fine again for a while. As only the code dont think the throttle body has gone as runs great all the way through when that doesn't happen. Any suggestions on what could be causing it?

[@ModMINI]

Have you replaced throttle body? They are pretty cheap used on eBay. ebay.to/2R8Xl7B

[@Millicente]

I'm thinking about buying an 05 mcs but don't think I will be doing my own repairs. No tools, no (garage) space, and no experience. It's got tons of service records but it's got 80k miles so it'll probably hit the big ticket maintenance items soon. Am I looking at a situation where I'm spending tons on mechanics in the near future? It's had most of the usually leaking seals replaced i think, nothing replaced in terms of the suspension though probably, unless mini did it themselves within the 60k miles it was taken to them for regular servicing which I doubt.

[@ModMINI]

I can't comment on any specific car. The typical issues are leaks and that sort of thing, then control arm bushings or leaking CV boots. get any candidate car inspected before buying.

[@lorenkohler5515]

I bought the Creator c310+ and I don't see how to rest the throttle adaptation. I changed the TPS/throttle valve and don't see how to get the C310+ to reset the throttle adaptation. Any ideas??? Thank you!

[@VMCJR0NE]

I bought the same tool but it won't connect to the throttle to clear the adaptation it only conects on the ecm to see the info it doesn't give choices to reet from there either. What would happen if we don't clear the adaptation. Can you help.!

[@MarvelousYoUnAstro]

I have a 2005 r50. I recently replaced the cylinder head and now it won't start. It starts for a little bit and dies out. New coil pack, wires and spark plugs... also a new camshaft position sensor... could it the throttle body sensor? Or stuck on limp mode?? Or the anti theft system?? The only codes that show up when scanning the ecu are 5e19 and 5e5c. Could you please help.

[@ModMINI]

Verify correct chain timing

[@MarvelousYoUnAstro]

@@ModMINI the sprocket and chain markings were set right to my understanding, cylinder 3 and 4 didn't respond to the pressure test... i ended up buying a used motor and having a mechanic install it... should be back on the road soon. Thank you for your reply. Your channel is very useful to us mini lover, bless you always and stay safe!!!

[@matthew3668]

Will be removing it just for a clean, should i unplug the battery before doing this? Have an r53 with problems starting. It has always started, but takes the engine a good 7 seconds of the starter motor turning for it to turn on. Once it does the exhaust smells rich with fuel. Recently changed spark plugs, battery and fuel pump to try to address the issue without success. Also, Here and there the code P0138 pops up, pointing to the lambda sensor after the cat convertor, could that also be why the engine is flooding itself before turning on after 7 seconds? Running out of ideas to check, thanks for anyone’s input.

[@ModMINI]

No need to disconnect battery. Try replacing fuel filter.

[@matthew3668]

Mod MINI thanks for your reply! will try replacing it too.

[@matthew3668]

Quick update. Still the same issue after changing the fuel filter. Updating this thread with info for any MINI owners with the same problem later on.

[@alfredbernal8603]

@@matthew3668 Did you clean your throttle body?

[@matthew3668]

In the end it was the fuel pressure regulator! Sorry for the late reply 😂 but just got to fixing it now

[@BryanBalu]

Hi there, i have a mini one r50 automatic, its in limp mode and the rpm won’t go more than 4,000, you think this is the problem? Hopefully you can help me or someone can many thanks in advance

[@vangrandvangrand928]

I ve changed that and the gas filtrer..the car takes forever to start when it gets a bit hot. It performs perfect when it start( so its not the pump)..what should i do;

[@ModMINI]

Leaking fuel injectors maybe

[@vangrandvangrand928]

@@ModMINI thanks for the advise man

[@vangrandvangrand928]

@@ModMINI injectors cleaned and checked properly by a trustful mechanic guy. The car still does not start easly after a normal drive and ,like before,it starts immediately when it sits a hole night.. (The injectors was very dirty and the car runs smoother but the problem remains).the guy told me about a part of the fuel pump that might not shut off right and leaves air in the system..) what should i do?

[@aomanchutube]

Hey, so my mini makes a hissing noise by the throttle body. It's not turbo charged. Doesn't smell like a coolant leak either, so I'm thinking it's the throttle body. Another symptom is that after you press the accelerator the engine takes a little too long to come back to idle at 1000 rev/min. Does this sound like a l need to replace the TB?

[@ModMINI]

Perform smoke test and fix source of air leak. Car computer is confused due to introduction of unmetered air.

[@aomanchutube]

@@ModMINI how might I go about doing that?

[@cesarestrada8705]

I changed the throttle body like you did, but I didn’t reset it, and it works great but when I changed the throttle body the abs now are failing, actually the mini show me some codes and I don’t know how to repair it, can you help me with that?

[@ModMINI]

you need a diagnostic scanner that can read the DSC module codes to know what is wrong.

[@cesarestrada8705]

@@ModMINI thank you a lot! actually the throttle body was fine, but i had a problem with the battery and that was doing the problems

[@BelRiose2000]

Do you have any idea what might cause EP (emergency program) on automatic R52 with sport mode and paddles? Continuosly lit. It can still shift, not stuck in one gear.

[@ModMINI]

Need to scan the computer and read codes.

[@hiimvictor8999]

Even if my issue is irrelevant to the video I still have to click it and hit like period

[@ModMINI]

Yes, you have to click it and hit like. That is the rule.

[@randelldanner8588]

My 03 base model standard just started doing this. Is it really that simple of a fix? I googled it and all the chatter made it out to be a big deal. For under $100 for the T. B. On eBay it seems worth trying to diy. If it doesn't fix the prob at least I have a new T. B.

[@ModMINI]

This has fixed the problem for every car where I've seen this code (4-5 cars)

[@yunbow5630]

Hi, I have 06 cooper s and have a code P0303 and P0313, and the engine light is on. I have replaced the spark and the coil but the code is still there. I think it's the problem from the injector or the fuel pump. Any suggestions?

[@yunbow5630]

Many thanks for your video

[@ModMINI]

You would need a diagnostic scanner with live data stream capability to figure this out. Could be anything without doing further diagnostics. Burnt exhaust valves are a common problem on these cars as well with higher mileage

[@yunbow5630]

@@ModMINI Thanks so much for your reply. I have a ODB scanner that can show the live data. What spersific numbers should I look at. I'm also thinking the head gasket leaking can be the problem because i can see some thin oil floating on the water tank. The car runs good. But when i stop and the temperature is up and the fans and water pump begin to work, then I can feel the misfire. Many thanks for the help!!

[@ModMINI]

@@yunbow5630 It is beyond the scope of a comment section to advise what should be normal live data, but you don't need a scanner to tell you that you should suspect a blown head gasket based on the symptoms you are now reporting. The coil pack almost never fails, by the way

[@SR-cp1eo]

I have the same codes except 1126, went limp mode on me on the way home late last night. It's happened before, dealer said it was a leaky boot. Same codes as last time. Think it's the same thing? Throttle body?

[@ModMINI]

Do a smoke test. Could be throttle body.

[@norildaaponte5794]

Hi im having a problem with the full body throttle too on my 2009 mini. I spoke with the mechanic but he doesnt even know the part number for it. Im trying to find someone that can help me with the part # at least thanks

[@raptorcon2391]

Hi I have a 02 Mini Cooper s and it idles rough but otherwise acceleration seems pretty good until today I was driving accelerating about 3/4 throttle and all sudden at 3k RPMs it felt like the motor shut off like it completely lost power I let off and then it was good now every once in awhile around 3K RPMs it does it when I'm accelerating fast. Earlier today the check engine came on and it did throw p1125 and p0442 codes but then it turned off now the light came on again after It started stumbling but I haven't checked the codes again yet. Would you have any idea what the issue could be.

[@ModMINI]

Could be throttle body. Easy enough to replace with a used one and see if that helps.

[@raptorcon2391]

@@ModMINI ok I guess I'll try thanks.

[@raptorcon2391]

Hi I bought the c310+ scanner tool that you linked from Amazon to reset the throttle body but I can't seem to find where to reset it on there could you explain to me how to do it please?

[@xstorm_8_shadowx]

2003 mini , check engine light is on but there’s no issues but if I come to a stop and let it idle the check engine light starts to flash and engine changes to run not so good. I can turn it off and back on and it resets the issue and this only happens when it idles never while driving. Even sitting at a stop light I can hold the gas to keep the rpm’s at 1500 and it doesn’t trigger the light to flash.... any ideas off hand?

[@ModMINI]

read the codes.

[@xstorm_8_shadowx]

I don’t have a code reader, money is tight and have no tools, long story but kind of starting over in life....lol. I was just trying to get an idea but thanks for the reply at least. Your videos are excellent and I’m glad there’s people like you doing these types of videos for others....Easy to follow...

[@mrTwoLai]

Sir can you hellp me where port code 2138 .. im new use mini cooper r53

[@fraseramos4029]

Can anyone tell me where to get the red trim that I’ve seen in the Mini Cooper on this channel, both inside the car on the doors and inside the headlights?

[@ModMINI]

You can't buy it. I painted them myself.

[@fernandoolivares2558]

When I’m in neutral I can floor it and it won’t go over 1000 RPM I changed the coil pack , new spark plugs and the same I wounder to see if you could help me out on this 🤦🏻‍♂️

[@ModMINI]

scan for codes.

[@VMCJR0NE]

What would happen. If we can't reset the adaptations on the throttle body

[@ModMINI]

May have check engine light

[@Stachlesss]

Do you happen to know the torque specs for the TB bolts?

[@ModMINI]

Sorry no. They'd be the same as any other bolt of the same size. though.

[@aomanchutube]

Probably just tight, but not too tight... LOL

[@liorbarkai1674]

I ordered the Creator V8.0 C310 and just found out that it does not support the throttle body adaptation, just clear the fault code. Unfortunately it is not worth to return it due to the shipping fee back (I leave in Israel) :(

[@ModMINI]

It should probably sort itself out over time.

[@Cheetacannon]

My dashboard turns on by its self after i turn off my car and wont turn off causing my battery to die. The only thing I have found to stop it is to leave my mini in reverse I have a 2003 R53. Would you know what could cause this?

[@ModMINI]

Not the throttle body. Not sure. Run a full computer diagnosis

[@fernandotabera7669]

hi thanx for your video it helps me to repair my mini and i appreciate to mutch your knowlege i ready to take a drive in a minimod #thanxminimod

[@Tugboatpb]

Are eBay throttle bodies safe to use? I would think for something like that you'd need OEM

[@ModMINI]

I would buy new OE manufacturer or used over new aftermarket.

[@dascrub2489]

Do I have to reprogram

[@pepperonipizzaslice8192]

Great Video as always

[@GarthGoldberg]

Did the throttle body really crap out at less than 73,000 miles?

[@ModMINI]

It is unusual/rare for a throttle body to go bad. I've only seen two and both were under 70k miles. There may have been a bad batch.

[@bvcxzgt5451]

@@ModMINI Mine appears to be gone at 96,000. Some people report success after cleaning the contacts and throttle body.

[@fernandoolivares2558]

Mine does go over 6 miles and hour on first gear and on second it’s 20MPH and and when it’s on idle the whole engine shakes and it says eml and service engine room but no check engine lights

[@ModMINI]

Scan for codes.

[@cracked302]

Is there a way to contact you about an issue I’m having? I’ve gone to a MINI racing shop with a lot of knowledge and I’ve done my research. No one on multiple FB groups can figure it out as well as the shop after over 7 hours of inspection and testing.

[@ModMINI]

If you've gone to shops that have looked at the car in person, and still unable to give you an answer, I will be of no additional help not being able to see the car.

[@Wearephuct-O]

Great! Thanks a lot!

[@tirapoljulrangsri506]

Hi Mod MINI I've got the error code :1689, 1125 and 0638 on my mini cooper s 2006. I think i wiil change the throttle follow your video I don't know will it work by the way Thank you for your helpfull video.

[@marcom4429]

Hello I love your channel, can you please put subtitles in Spanish? greetings from spain seville

[@ModMINI]

Sorry, I don't speak Spanish. I have enabled the community contribution setting which allows viewers to submit their own.

[@pboperations]

Typical Spaniards asking you to work for them by putting subtitles in a foreign language.

[@ChrisNieves]

like the others another great video.

[@vsenarma]

Excellent video....I just my 2005 mini cooper S..

[@aevans692]

great vids ..

[@SingerAuto1967]

What if the only code your getting is P1125

[@ModMINI]

I'd still suspect TB.

[@Jsauce8921]

Thanks!!

[@orenlv]

hi, which head camera do you use ? Thanks !

[@ModMINI]

GoPro

[@minimanadam]

Lol , WE all forget the snorkel until the end.. mini life......

[@Krizzleswg]

New video YESSSSS :D :D :D

[@telecasteredtodeath]

The dud throttle body was very clean.

[@ModMINI]

They usually are.

[@dha588]

The way you know that you need a new throttle body, when you buy a mini.

[@sshaunss]

Had this past few days eml light came up would still run but slow or in neutral would just make a chugging noise hopefully it’s this