Montech KING 95 Pro - Part II [Thermal Test]

[@metromelvin]

Great work. Loved the explanation and presentation as well. 🥰 Points to note: 1. Arctic 280's are one of the best you can get, period. however the mount that has the tubes on the top of the radiator is something I would not recommend because in time any radiator will have some kind of water loss and it will cause issues in the long run (gamers nexus has a detailed video on this). 2. I can understand that you are placing the fans inside the radiators for aesthetic purposes, however in my experience (not on montec fans btw) Pull config can only match push maybe after 2000 rpms, so for lower RPMs I'ld mount the fans pushing through the rads and not pull. This guy had done an excellent job creating this video. If someone is gonna replicate this build you may consider this comments depending on the fans you are using and the RPM's you are trying to run it at on a regular basis.

[@KleoYan]

Hi metro melvin, welcome to my channel. I should have spoken your point 1. and 2. which I totally agree on. infact part of the reason I did this as I am curious how the system react using Montech fans. Personally, there is one more point, it's not advisable to use reverse fans on radiators. There are limitations to unleech the full potential of a system. Is either you go with asethetic vs performance. Personally I will prefer performance over asethetic. Thank you for your feedback, greatly appreciate it.

[@metromelvin]

@@KleoYan ❤

[@RanjakarPatel]

I enjoi

[@KleoYan]

@@RanjakarPatelhi welcome to my channel. So sorry that you did not enjoy this and do pardon me as I don’t speak your language. Thank you for the visit 😊

[@RanjakarPatel]

@@KleoYan thanks my dear. i see you are kindness and i will give four your subscribe. my english no powerful but i enjoy singapore people and they are amazing. you do good but maybe i no understanding. thank you and good luck four you

[@minawater5106]

amazing, thank you man

[@KleoYan]

Hello minawater, welcome to my channel and I am glad you like my content. All the best with your build. 😉

[@jomama6870]

Two part reviewing this case help me made decisions to buy this case...thanks for the content....😊

[@KleoYan]

Hi MR B, welcome to my channel. Thank you for your feedback. I am glad these two content did aid you, all the very best with your build too. 😉

[@南埜光莉]

Nice to meet you! Your airflow experiments were very helpful. I bought the King 95 pro and it was very helpful.🎉

[@KleoYan]

Hello 南埜光莉, welcome to my channel. I am glad my content did help you. Thank you for your feed back and all the best with your build too. 😉

[@noxmu4715]

7 days 😱. You are one of a kind for a reviewer, this is why I trust what you have presented Your efforts are greatly admired, salute with respect. By the way, I have ordered this case from newegg. Thank you Kleo, you did a fantastic job again.

[@KleoYan]

Hi Nox, welcome back. Thanks for the kind words. I will continue to try my best to bring better content 😉

[@jsnb85]

Good stuff!!! Thank you!

[@KleoYan]

Hi jsnb85, welcome to my channel and thank you for your feedback 😉

[@starofeden9277]

phenomenal and superb great work great explanation im now on the verge of thinking to buy this case found 2 videos so far showing air flow of this case but you are doing it the best

[@KleoYan]

Hi Star of Eden, welcome to my channel and thank you for your feedback.👍👍👍 Infact I am currently using this case and the thermal is superb. Just to share, this is my build www.reddit.com/r/MontechPC/comments/19esupr/project_montech_king95_pro_sonic_the_hedgehog/ and I wish you all the best with your build too 😉

[@jmfrost86]

Another great review! Thank you for the time spent and the thermal results. Take care!

[@KleoYan]

@@jmfrost86 hi and welcome back. Thank you for your valuable feedback and all the best with your build too 😉

[@DYrahcaz91]

Your video did a fantastic job going to a level of detail in thermals! Thank you for putting in all that time! Very informative video - well done!

[@KleoYan]

Hi Zachary Diezel, welcome to my channel and you are most welcome. I am glad you like my content. All the best with your build too. 😉

[@jeremyyip6839]

Just bought the case, so glad I find this video. Keep up with the good work bro!

[@KleoYan]

Hi Jeremy Yip, welcome to my channel. you will going to love this case like I did 😉 Thank you for your info and feedback. 👍👍👍

[@r200ti]

Nice piece of work. Very thorough and detailed testing.

[@KleoYan]

Hi Jason Davis, welcome to my channel and thank you for your valuable feedback. All the best for your build too. 😉

[@chaechae2424]

hey man i bought the case and watched your reviews. You do the most in depth case reviews i have ever seen. good work

[@KleoYan]

Hi chaechae2424, welcome to my channel and thank you for your valuable feedback, greatly appreciated it. All the best with your build too. Just to share, this might interest you as I have done a full build on it. www.reddit.com/r/pcmasterrace/comments/19f113a/sonic_the_hedge_hog/

[@Den22Ri]

Thanks for the quality tests, greetings from Russia

[@KleoYan]

Hi Denis Rogachev, welcome to my channel and thank you for visiting 😉

[@cubancoffee]

You have the best case reviews I have seen! Loved the Asus AP201 based on your reviews and just purchased this case and I am confident this will be a spectacular case.

[@KleoYan]

Hi Joe G, welcome back and thank you for your kind words 😉yup, this case is indeed very unique, I myself grow to like how it looks 🤣

[@msaber1797]

The 200mm EVGA Supernova 1600 G+ fit without modification to the rear tray. It didnt want to, but I got both screws back in and it fit without much issue. It's definitely touching but it works.

[@KleoYan]

HI msaber1797, welcome back. for me I can't even place my PSU in. I can't close the tray but I am glad it did for you. Thank you for the update and info shared. Greatly appreciated this. If anyone whole ask me to able EVGA Supernova 1600 G+ I will share your piece of information. Thank you again.

[@icarusgeo]

Uncle Roger making case reviews now? Fuyoh! 😄 Great, thorough video as always 👌

[@KleoYan]

Hi Icarus, welcome back and thank you for the feedback. Am glad you like my content 😉

[@dwaynecarter85]

@Kleo Yan thx for this video, helped me a lot which case i'll buy next. especially i have the liquid freezer ii 360, too

[@KleoYan]

Hi Fenris, you are most welcome and all the best with your build too 😊

[@bryan8946]

High quality content bro, subbed

[@KleoYan]

Hi Bryan, welcome to my channel and thank you for your feedback and to subscribe to my channel. All the best with your build too 😉

[@JJ-gk5tn]

BTW u can remove the swinging part in the back without tools and u don't have to use it so every PSU will fit

[@KleoYan]

Hi JJ, welcome back and yup, that's corret, thanks for the feedback.

[@emo137]

i think its better you upload full video build pc using this case,good content bro

[@KleoYan]

Hi Emogame, welcome to my channel and thank you for the good suggestion, I will do that in furture. By the way there is a more detail content of this case here kzbin.info/www/bejne/jJSUfndml8eWpacsi=jCCAASAmYvFrIMXk . Do pardon me as I have finished building this case and this is the end result. www.reddit.com/r/MontechPC/comments/19esupr/project_montech_king95_pro_sonic_the_hedgehog

[@Nico-ub1pv]

One good looking case!

[@KleoYan]

Hi Nico, welcome back and thank you for the compliment, it's not fully done up yet hahaha.

[@serefx07]

wow, very detailing. nice work👌

[@KleoYan]

Hi seref öztürk, welcome to my channel and thank you for your valuable feed back 😊

[@marknewellmusic]

Montech owe you a beer, just sayin' 😊

[@KleoYan]

Hi Mark Newell, welcome to my channel. Thank you for your kind words, greatly appreciated it and all lthe best with your build too.

[@djimty]

I cant believe I have only come across your videos now! Now i'm torn on what to buy, either this or the Lian Li O11 Vision to run my hot 5800x?! BTW I've subscribed, really love the detailed review and you make brilliant content! Great work, keep it up and now I'll be watching all of your videos! :)

[@KleoYan]

Hello Emtiaz, welcome to my channel and thank you for your valuable feedback. Yup both cases looks good with its own ways. I do have a struggle between the o11 vision and this montech King95 Pro. I ended up with this chassis. Part of the reason is, this offers better thermal which suits my needs in hot and humid country. Next is the color which allows me to theme with my motherboard. Just to share www.reddit.com/r/MontechPC/s/CXXeOazCzG . I wishes you all the very best with your build too.

[@johnpan2654]

have to admit, you have done the great job expecially for this case. I searched this case and got direct into your youtube chanel. Subscribed and thumbs up. Hopefully you will have more content coming out soon. I love the chanel but it maybe too geek for someone else but that's my taste.

[@KleoYan]

Hi John Pan, welcome to my channel and thank you for your valuable feedback. maybe this might interest you. It's not about MX6 but more on if your thermal paste have the viscosity, you might want to try this method as it benefit in thermal improvement and less wastage on thermal paste.kzbin.info/www/bejne/rouVg2eopKtklbM

[@mercurio822]

Thank you for the tests, im going with F1. but im going to place my 280 IO on top i think.

[@KleoYan]

hi Mercurio, welcome to my channel. That's good, all the best with your build too and do share with us your findings, thank you 😉

[@mercurio822]

@@KleoYanYes Soo compared to my Lian li Air mini where i had a radeon 7900xt sapphire pulse and a ryzen 7900x with a arctic 240, i now have a setup With almost Twice as many case fans aswell. and All of the case fans are bequiet 3x Slient wings 4 and 2 silent wings 3. and ive swapped my Grapich Card to a Radeon 7900xtx sapphire pulse as i got it for the the same price that i bought my 7900xt for. my 7900x is now using a Be quiet Silent loop with 2 Silent wings 3 fans on it. The 7900xtx is pushing 100w more and is currently not undervolted, but i am using Radeon chill in most games and still it pulls around 300w. and has peaks in full useage at about 375w, which is mind boggling as my 7900xt usually pulled around 280w and peaked at 320w. So alot more heat is being dumped into the case in gaming, which is not that good for my 7900x temps as i suspect most of the heat is going there, but ive resorted to undervolting and tuning power and thermal limits on it, so it has dropped from peak 85c down to about 75-80c in full load gaming. my GPU barely passes 75 hotspot. it got two 140 Silent wings 3 bellow it pumping up air and i got two 140 Silent wings 4 in the side intake at barely audible for extra air intake, and one air exaust in the back a 120 silent wing. im considering if i should let the back fan pump in some more air, but i doubt it would do any good, and i dont think moving the AIO to the side mounting is a good idea, but everything apart from the CPU and the AIO is getting hot. i just think i need to power limit the GPU down to 300w.

[@amitpatilbhujbal7050]

Great, nice

[@KleoYan]

Hi Amit Patil Bhujbal, welcome to my channel and thank you for your feedback. All the best with your build too. 😉

[@John_the_baptized]

Amazing work! Thank you!

[@KleoYan]

Hi John the Baptized, welcome to my channel and thank you for your valuable feedback. All the best with your build too.

[@desiderio4844]

Would you look at that, wow! The Arctic 280 really is a good cooler. Now, I wonder if it's possible to install the tube at the bottom with GPU vertical configuration.

[@KleoYan]

Hi Desiderio, welcome to my channel. Yes it is possible if you using mounting bracket like the Cooler Master V3, where you can move the GPU towards the side glass panel to give clearance for the Arctic LF2 tubes to be located at the bottom and to tug behind the GPU. If the gap is narrow where the GPU is near the motherboard, then it's not possible.

[@desiderio4844]

@@KleoYan Thanks for responding. This chassis is on my top list so far and so is the Lian Li Lancool3 because of your review. I have an Arctic 420 LF2 on a P500A chassis, but it's not possible to install the cooler with tubes down in front. I'm still doing my search, but your reviews helped a lot. Thanks man.

[@KleoYan]

@@desiderio4844 I see. I hope you will find a case which enable you to mount the hose below instead of above.

[@ML_EU]

I'm... shocked :D Two movies with the most in depth reviews I've ever seen in the internet :D You should be hired full time on KZbin and make millions every month :D Did you measure the distance from front mounted plate to front glass? I wonder if I can fit 360 rad at bottom with flat pump-res on front, 240 rad on side and 360 on top :D

[@KleoYan]

Hi Marcin, welcome to my channel. if you are measuring the tray depth to the front mesh cover, it's at 40mm. if you are measuring the tray where the 25mm fans touches the tip of the tray to the tip of the front mesh, it will be at 15mm. hope that make sense.. once again thank you for your valuable feedback and question. All the best with your build too.

[@ML_EU]

@@KleoYan D5 pump height in flat res is 46mm, damn. My whole plan has just been blown up haha :D

[@KleoYan]

@@ML_EU so sorry to hear that.

[@kimisami88]

Brosef, did u place the two fans u removed from the side for the 280 AIO to the top? Was wondering where the airflow up top was coming from?

[@KleoYan]

Hi Kaminosami, welcome back, for this test, if it's of the top (not with the AIO), I have use 3 x 120mm fans and not 140mm fans. hope that helps.

[@kennethz3366]

How much temperature difference between traditional cases use 3 front intake fans vs dual chamber case use 3 side intakes fans?

[@KleoYan]

Hi Kenneth Z, each case and fan used in a system various. Of course the traditional front intake chassis with good ventilation mesh holes will be slightly better in thermal as compared to a dual chamber. But you can tweak the airflow.. I am currently using this dual chamber and yeild very good results. you can refer to and to read what I've installed in this case. www.reddit.com/r/MontechPC/comments/19esupr/project_montech_king95_pro_sonic_the_hedgehog

[@jurgens.9029]

Thank you for this greate video.👍👍👍

[@KleoYan]

welcome back Jürgen, I should be thanking you to have supported and to watch my content 👍👍👍

[@travistuckerSB]

Did you try a push-pull 280 leaving the stock Arctic fans as intake on back-side of case? Curious if that drops temps even further since fans would go to waste otherwise.

[@KleoYan]

Hi Travis Tucker, welomce back. Yup I did, they perform much better on P12 ARGB alone without push pull configuration. with push pull it drops about 2 to 3 degrees.

[@Shahriar.H]

I have two questions 1. Is this case good enough to keep cool a 14900k using an Arctic Liquid Freezer II 360mm and a RTX 4080 Super under load? 2. If I use an EATX motherboard like MSI Z790 Ace Max on this case, will the Arctic Liquid Freezer II 360mm interfere with the motherboard heatsink? Your response will be greatly appreciated, thank you.

[@KleoYan]

Hi Shahriar Haque Asif, welcome to my channel. This case is good enough to cool your components and you can fit the liquid freezer II 360 with the E-ATX motherboard without issues.

[@Shahriar.H]

​@@KleoYan Thank you for your response. Can you do an in-depth review like this for the Gamdias Neso P1 case?

[@KleoYan]

@@Shahriar.H let me see what I can do. No promises, going to write in to request. Thank you.

[@bergdk237]

KleoYan, great work! To be honest for the PSU clearance part, i was already thinking of removing that back plate, i do not use extra ssd or planning of using extra fans, and was thinking it could instead give slightly more clearance for the intake airflow, by removing that plate😄 Also Would you say the montech fans are just decent for performance? or actually of good performance and rgb quality overall?Would it work fine to use like all lian li fans with the montech pre installed fan hub? Personally i still think having a 360 aio at the top, is for me the most visually pleasing, and using the standard Montech fan configuration out of the box, seems to be overall well balanced! So intake side, bottom intake, back exhaust, top exhaust😀

[@KleoYan]

Hi BergDK, welcome back and to answer all your questions. Q1) Also Would you say the montech fans are just decent for performance? or actually of good performance and rgb quality overall?Would it work fine to use like all lian li fans with the montech pre installed fan hub? A1) Montech fans are decent. though they might not perform extremely well but they are quiet. the argb defusion is good. I would not advise you to use the lian li uni fans on this montech hub, best if you use uni fans, it is to use it's own controller/hub. there are fan profile and ampere profile on those fans. more power hunger. Q1) Personally i still think having a 360 aio at the top, is for me the most visually pleasing, and using the standard Montech fan configuration out of the box, seems to be overall well balanced! So intake side, bottom intake, back exhaust, top exhaust A2) Yes if you know how to tweak your processor and to do some minor adjustment on your fan curve for these Montech fans, you will be fine.

[@bergdk237]

@@KleoYan thx

[@KleoYan]

@@bergdk237 you are most welcome. All the best with your build buddy 😉

[@saifadailh2456]

Hi Kleo Thanks for the great review! quick question : did you face any problem in installing the 280mm rad? I am planning on using Kraken 280mm rad on the side(not on the bracket) and 2 140mm fans on the front, will this work?

[@KleoYan]

Hi SAIF ADAILH, do pardon me as I missed your comments. Yes I did with a GA II 280 LCD but I need to have it push pull as I can''t fit the radiator directly to the side fan tray and I will need to mount my GPU Vertically just to clear space. As for the Kraken 280mm, I do not have a unit to test it.. so sorry about it. By the way this was my final build www.reddit.com/r/MontechPC/comments/19esupr/project_montech_king95_pro_sonic_the_hedgehog/

[@saifadailh2456]

@@KleoYan thanks for the reply! Do you recommend the king or lian li 216, I care about noise and temps mainly

[@KleoYan]

@@saifadailh2456 I will go for king 95 pro. As those AX or RX fans that comes with the case is quiet. Does perform if you plan the airflow properly. For Lancool 216 is good too but the front fans are abit noisier.

[@mellomd888]

nice video! can i control fan speed and rgb by software?

[@KleoYan]

HiMello MD, welcome to my channel. Yes you can control the PWM of the fans using your motherboard utitlity, same applies to the argb.

[@JJ-gk5tn]

Can you ask montech when this case will be available in Germany?

[@KleoYan]

Hi JJ, welcome back. will try to ask but you might want to follow this reddit post. www.reddit.com/r/MontechPC/comments/18bbf7m/review_montech_king_95_pro/ or you can email them direct to ask [e-mail]

[@namirs9732]

I have a question, where did you plug ur fan hub into? I plugged my 3 pin into the 5v, rgb and the 4 pin into the 12v grb, my bios is not recognising them, any fixes?

[@KleoYan]

Hi Sriman Arya, welcome to my channel. By default before you plug anyting to the Case Fan/ARGB Hub. take note that there are three cables that are on it. 1) a 4pin pwm cable 2) a 3pin 5v argb connector 3) a sata cable plug 1) to motherboard fan header and take note of the header (example CPU_FAN) plug 2) to motherboard 3pin 5v argb header plug 3) to your PSU sata cable once you've done the above, plug your fans argb and pwm to the hub. you can now see your fan readings in UEFI under CPU_FAN and argb on the argb motherboard header.

[@namirs9732]

Ok, but can I set it to chassis fan? Also won’t all of them move at once? I want to get the exhaust fan to push more than intakes

[@KleoYan]

@@namirs9732 ok. maybe watch this unofficial content which I have explain to my peers at a forum. The fan/argb hub in this content works the same as the Montech pro fan/argb hub. kzbin.info/www/bejne/rXaqip2PhayBbK8 Infact I call it a controller and this is how I set up my system in this case to have total control of all the fan set rpm. Side fan tray - my 280 Liquid AIO with push pull configuration 4 x 140mm fans to the fan/argb hub and plug the pwm 4pin from the hub to CPU_FAN 1 Top fans (3 x 120mm) - Exhaust, plug to Cha_Fan 2 Bottom fans (3 x 120mm) - Intake, plug to Cha_Fan 5 Rear fan (1 x 120mm) - Exhaust, plug to Cha_Fan 1 For my AIO which the fans are plug to the hub as I wanted the drawing power of the 4 x 140mm fans to be getting sufficient power from the PSU direct but able to control the PWM as it's plug to CPU_FAN as for the Top, Bottom and Rear, Since the sets are plug into the individual fan headers on the motherboard, I can control the PWM curve separately. example top to run at 800rpm min , bottom to run at 1000rpm min and rear at 1400rpm min. as for all the argbs, since using the case button, I have connect all the fans to the hub directly.

[@namirs9732]

@@KleoYan Sorry sir, I am very new to the pc building scene, are there 2 cables off of each fan? I understand they are daisy chained, so I would only need one to plug into the slots, but what should I plug in? I would assume I need to plug in the connectors on the bottom of the hub…

[@KleoYan]

@@namirs9732 the fans itself have a 4 pin and 3 pin. 4 pin is to drive your fan to spin, 3pin is to drive the ARGB effects. You can daisy chained them accordingly and plug to their respective headers on the motherboard. I have shared a video on content on my previous message. Kindly watch and understand how things work first. Thank you.

[@Antonio-rg1cy]

So I have the same sag holder from Asus TUF 7900xtx If i put it of the mid of 2 and 3 fans down of the gpu will stay good? :D I plan to buy this pc case but worry so much about my sag on GPU becouse TUF 7900xtx is so big gpu ? ( sorry for my bad english) xD

[@KleoYan]

Hello Antonio, welcome to my channel. Yes is all good. It depends how you place the support stick.

[@SkullModder]

Great review

[@KleoYan]

Hi 8bit phoenix, welcome to my channel and I am glad you like my content and this is the final build which might interest you. www.reddit.com/r/MontechPC/comments/19esupr/project_montech_king95_pro_sonic_the_hedgehog/ 😉

[@SkullModder]

@@KleoYan it came out really nicely!. The sonic theme worked well. I plan on getting the red version here in a week or so, it was nice to get an idea of how my build may look.

[@KleoYan]

@@SkullModderhi thanks and I wish you all the best with your build too 😉

[@MeterJeter1]

You know can take out glass from the front for much better results the glass is just for show a pc gamer just use a mesh.

[@KleoYan]

Hi Abraham A, welcome to my channel. Yup you can do that, this case have the capability to let you cool the way you want it. lots of configuration. Thank you for your valuable feedback.

[@НААТ]

I enjoy the fish bowl look so im def keeping the front glass. But when summer hits i can definitely see myself swapping it for the mesh panel. Balanced as all things should be.

[@KleoYan]

@@НААТ Hi, welcome to my channel and thank you for sharing your thoughts, greatly apprecitate it. Yup, indeed this case if flexible. 😉

[@ThePCExpertAmateur]

Some data point is missing, but I don't know what. :( A1 has the best CPU & GPU clocks, just like E1, but it doesn't have the lower temperatures of B3, C1 and D3. D3 has the best overall temperatures aside from the CPU, but doesn't have a great CPU temp and clocks, and does have a lower GPU temp and the highest clocks. I cannot see the causations between temps and speeds of the CPU and GPU. What isn't being tracked that might possibly show the real causation? Is it just that there isn't a temperature sensor somewhere that is actually important for the bus speed somewhere specific? Is the CPU throttling the GPU, or vice versus? What's going on? I've seen similar strange results in my own testing and I am baffled. I don't lock things down in BIOS, but I know you do, right? So confused! To put it another way, the temperatures of A1 and E1 are fairly different, yet the CPU & GPU clock speeds are identical. What is causing that? Not any temperatures that you or I track. I'm baffled. Do you have any ideas what the cause is?

[@KleoYan]

Hi The PC Expert Amateur, welcome back, I have stated clearly that I am concious of not allowing my processor to overheat, which I will need it for other content. as for the temperature which you do not get. I advise you to completely go through this content. If you still do not understand, I am so sorry to say that my English speaking is bad. Maybe you can request this case from Montech and to conduct your own testing. Do up a content and share it with us. Do pardon me as I will stop replying. I have tried my best to explain on this other content kzbin.info/www/bejne/mZKVq3qJhtuKpcksi=W13cTjsAl0PPwnPs but failed to let you comprehend what I've typed.

[@riadhz3461]

Hi there, after watching your video i have a question, I'm planning to build my PC and I'm having a lot of trouble deciding on the case, so I'd like to know from your personal experience, if a case with a front side fan is better than a case with a side fan overall?

[@KleoYan]

Hi RiadhZ, welcome to my channel. This case is build unique. For me I have done a 280 rad at the side. Push pull configuration to retain the fish tank look www.reddit.com/r/MontechPC/s/4yge4Q6vjF the curve of the glass helps a lot to push air into the case. You can choose either way to mount your fans and both are as good. Personally I prefer to place the fans at the side as intake.

[@dantosh7562]

Is there a reason you didn't use the bottom 3x120s as an exhaust and the top as intakes?

[@KleoYan]

Hi dan tosh, welcome to my channel. cool air raise from below.. hot air goes up. If you do the other direction.. your hot air will still be circulating at the top which will trap the warm on your PC components. Maybe you can give it a try and let us know the results as I have not done the style you have asked for.

[@tuubikuusela7847]

280 AIO on side mounted and blowing out?

[@KleoYan]

Hi Tuubi Kuusela, welcome to my channel. Kindly understand the content as I have tested in and out.

[@tuubikuusela7847]

@@KleoYan C1 but side out?

[@KleoYan]

@@tuubikuusela7847 C1 is air in through the radiator

[@tuubikuusela7847]

@@KleoYan Yes, can you test C1 but air out trough side radiator?

[@KleoYan]

@@tuubikuusela7847 that will be D3.

[@kof2]

So overall, is this casing good for us singaporeans (hot country) or is there another recommendation for dual chamber casing? The only thing I do not like about Lian Li is the USB is at the bottom. (I have no space, my PC has to be under the table.)

[@KleoYan]

Hi derek cheong, this case is good and if you use Montech AX or RX fans, you will need to tone down the power limit and to do offset, as I have illustrated here. Else if you use other fans like what I did, that is to use P12 ARGB and P14 ARGB from Arctic, they perform much better. I can get my CPU to 76 Degrees with the settings I have set here.

[@kof2]

@@KleoYan So the fans that came in the case is no good as in hotter? and its recommended to buy the case without the fans and put in your own fans? My current rig has bequiet Silent Wings 3 fans, I planning to upgrade once the rtx 4080 super is out. Is arctic fans better than bequiet fans? Would be happy if you can answer this questions.

[@KleoYan]

​@@kof2 as mentioned to you. correct, if you use the montech fans, you need to tone down but still usable. but if you want better temp, get better fans which will be above 1600 rpm. The choice is yours.

[@44Mercy187]

btw i wanted to ask what for colors it cycles trough?

[@44Mercy187]

The rgb button

[@KleoYan]

@@44Mercy187 pardon me. Didn’t get notification till I manually screen through the commentes. As what I saw while fiddling with the button. You have total of 7 static colors, white, purple, red, yellow, green, cyan, light blue. As for effects, what I see are these. Rainbow, chase, runaway, random cycle, heartbeat and glow.

[@44Mercy187]

@@KleoYan Ah thank you so much.Btw the liquid freezer iii came out i heard its very great i hope u can review it👍

[@KleoYan]

@@44Mercy187 hi and you are most welcome. As for LF3 yup will be testing it out. 😉

[@44Mercy187]

@@KleoYan LETS GO DUDE like there are like 3 cables for it or it can be one but idk which one goes where on the mainboard.Thank you

[@44Mercy187]

did you let your led 2 pin on the rgb hub?

[@KleoYan]

Hi its_Mercy, welcome to my channel, yup I just leave it.

[@44Mercy187]

@@KleoYan tyy btw what software do u use to control ur rgb

[@KleoYan]

@@44Mercy187 hi, I dont use any software, I just use the case argb controller to toggle the argb to white.

[@JJ-gk5tn]

Btw Wich fans are better Artic p12 or the montech fans ?

[@KleoYan]

Hi JJ, that will be Arctic P12 or P12 ARGB. The AX or RX Montech fans are for aesthetic. There is also a performance fan which is the Montech 120 Metal PWM. Those can beat the Arctic p12

[@shirleysiu5958]

This looks like a fish tank.😂

[@KleoYan]

Hi Shirley Siu, welcome to my channel and yup it does looks like a fish tank 😬 and this is the final build which might interest you www.reddit.com/r/MontechPC/s/xUx0naQHkB 😉