MOSFET Gate Drive Resistor Selection - Part 1: Turn On

  Рет қаралды 25,651

Biricha

Biricha

Күн бұрын

In this video, we will describe how to quickly select a "near optimum" value of your Gate Drive resistor in a MOSET driven switch mode power supply during turn on.
The methodology described here should give you a good comprise between fast switching speed, low EMI and low time to market without difficult measurements.
For detailed mathematical analysis and accurate equations, we highly recommend the excellent paper by By Mr. Laszlo Balogh, "Fundamentals of MOSFET and IGBT Gate Driver Circuits" available from TI: www.ti.com/lit/ml/slua618a/sl...

Пікірлер: 58
@CircuitShepherd
@CircuitShepherd 10 ай бұрын
The real fun starts when switching inductive loads 😉
@p_mouse8676
@p_mouse8676 10 ай бұрын
That's actually where most issues are in practice.
@DeltaSigma16
@DeltaSigma16 8 ай бұрын
😂😂
@gaynzz6841
@gaynzz6841 3 ай бұрын
Didn't you pay attention? The circuit is a flyback converter (4:20) which is really the most inductive as you can get.
@CircuitShepherd
@CircuitShepherd 3 ай бұрын
@@gaynzz6841 Yes, I was a bit unclear. Referred more to a simple step down. Normally you will never see a Miller plateau in such cases.
@dwagner6
@dwagner6 10 ай бұрын
KZbin's algorithm recommended your videos (esp. the Miller Plateau video) right when I was working on a related problem on a design. Very serendipitous...and your videos are great!
@baghdadiabdellatif1581
@baghdadiabdellatif1581 10 ай бұрын
Me too. I was watching eevblog about PCB current trace
@paulpaulzadeh6172
@paulpaulzadeh6172 10 ай бұрын
They put also ferrite bead too. One small ring ferrite bead in wire .
@alexandrosantos4099
@alexandrosantos4099 10 ай бұрын
Great videos Professor!!! Greetings from Mexico
@md.abubakarsiddique6390
@md.abubakarsiddique6390 10 ай бұрын
Your teaching skill is awesome. Thank you professor. Love you to see from Bangladesh 🇧🇩.
@JeromeDemers
@JeromeDemers 10 ай бұрын
awesome video!, I wish you could of talk about adding diode in parallel to resistor and see it's effect on the scope. You can also combination of diode and resistor to control the turn-on and turn-off speed.
@LordPhobos6502
@LordPhobos6502 6 ай бұрын
So... in your example, you end up with a 5ohm resistor... How would you cslculate what power rating that resistor needs to be?
@Mahesh-uy8jw
@Mahesh-uy8jw 10 ай бұрын
Thank you, Learned something new today.
@baghdadiabdellatif1581
@baghdadiabdellatif1581 10 ай бұрын
Great work 👌
@twhite3844
@twhite3844 9 ай бұрын
Very clear and helpful.
@Appregator
@Appregator 6 ай бұрын
Thanks - great explanation.
@Brumby0
@Brumby0 9 ай бұрын
Excellent, thanks.
@serhatdalga7038
@serhatdalga7038 Ай бұрын
Thank you , It is really very useful.
@autotuneengineering
@autotuneengineering 9 ай бұрын
Thank you!
@nickharrison3748
@nickharrison3748 Ай бұрын
Very nicely explained and demonstrated.
@AvishekDasPostdoc
@AvishekDasPostdoc 9 ай бұрын
Fantastic explaination
@ArjunaWeerasinghe
@ArjunaWeerasinghe 10 ай бұрын
Nice talk. Thanks
@vidtechnology7342
@vidtechnology7342 4 ай бұрын
Nice explanation , Thanks
@SMV1972
@SMV1972 10 ай бұрын
Очень понравилось видео! Нужный полезный практический урок. Спасибо Вам!!
@juniorthetuner5113
@juniorthetuner5113 8 ай бұрын
Wow thanks so this should be done under load...if I'm trying to rive a dc traction motor should I do it under load or off the ground freewheeling with the scope
@qaisarawan93
@qaisarawan93 13 күн бұрын
So we need to look at the gate to soyrce vootage and make a oerfect shape like you shown by choosing different gate resistor
@glasslinger
@glasslinger 10 ай бұрын
Hey, I thought I was the only one to "design by tweak" I tried the "math" way and the values always turned out wrong so ended up tweaking the values anyway!
@RexxSchneider
@RexxSchneider 10 ай бұрын
I must admit I was hoping for a bit more than "try different resistor values, and see what looks best on a scope". But that's fair enough advice in most cases, and you did supply the link to a more detailed analysis.
@ferrumignis
@ferrumignis 10 ай бұрын
He links to the paper that describes how to calculate the gate drive resistance provided you can measure the parasitics.
@RexxSchneider
@RexxSchneider 10 ай бұрын
@@ferrumignis Yes, indeed, as I remarked. Most of the time, of course, you'll have an estimate of the maximum parasitic inductance when you know the length and size of the leads/tracks between the driver and the mosfet. That's sufficient to determine the minimum value of resistor needed to damp the LCR circuit.
@ibrahimcafe9586
@ibrahimcafe9586 7 ай бұрын
Thank you very much sir
@sudheerkumar5966
@sudheerkumar5966 10 ай бұрын
Very good
@vishalr4551
@vishalr4551 7 күн бұрын
Sir do you know how to measure isolated voltage with optocouplers
@user-yn9cc6bw8b
@user-yn9cc6bw8b 10 ай бұрын
Great experiment. And what will be if you use 0 ohm resistor with the ferrite bead on the gate pin of the MOSFET?
@EhsanHabib
@EhsanHabib 5 ай бұрын
Did you try it ???? Let me know if you have done it
@calypso5925
@calypso5925 10 ай бұрын
Please clarify where is the oscillo probe connected. To the mosfet gate?
@zeljkoadzic1692
@zeljkoadzic1692 2 ай бұрын
Hi. Does this apply to inductive loads as well as to the logic level signal? is there any formula for gate resistance ?
@panditji8823
@panditji8823 8 ай бұрын
Sir, We have to keep underdamped position to the waveform and need to keep less than 10 ohm resistor.
@Rostam67
@Rostam67 2 ай бұрын
Thanks a lot for the great video. Is it possible to use a whiteboard instead please? I understand that this is a weird request. But the marker on paper makes a sound that is hard for some people (not everyone) to tolerate. I am sorry for this strange comment. Thank you again. you rchannel is amazing.
@qaisarawan93
@qaisarawan93 15 күн бұрын
😢mee too
@retokeller1400
@retokeller1400 10 ай бұрын
Does the oscilloscope's probe capacitance (e.g. 1pF) not change the gate signal too much? Or is the gate capacitance order of magnitude bigger than the 1pF of the probe?
@volodymyrzakolodyazhny7740
@volodymyrzakolodyazhny7740 10 ай бұрын
Gate capacitance is hundred or hundreds picofarad at least typically and oscilloscope probe is 12-25 picofarad (fine one) so it doesn't change much. If you work with more powerfull transistors it is neglisible. It is only consern at rare cases.
@RexxSchneider
@RexxSchneider 10 ай бұрын
As real examples, a power mosfet like the IRL530 has a typical input capacitance around 1nF and the IRFZ44 around 2nF, while for the small-signal 2N7000, it's just 60pF max.
@retokeller1400
@retokeller1400 10 ай бұрын
@@volodymyrzakolodyazhny7740 Thanks
@retokeller1400
@retokeller1400 10 ай бұрын
@@RexxSchneider Thank you
@lohikarhu734
@lohikarhu734 9 ай бұрын
as a 10:1 passive probe is typically around 11 pF, it won't load the drive path very much, relative to the gate capacitance of a big mosfet, but really loads a smaller device, where an active probe becomes indispensable! Also, a typical passive probe, if you use a "ground lead" often adds a resonance at 100-125 MHz. probing is always raising its head as a tricky factor in switching analysis...
@nickharrison3748
@nickharrison3748 Ай бұрын
dosent the calculation affect fall time
@inductivethinking
@inductivethinking 10 ай бұрын
But what if you're just switching on/off a load (no fast switching requirements) ? Wouldn't a high resistor value be preferable, in order to get lower emi emissions?
@volodymyrzakolodyazhny7740
@volodymyrzakolodyazhny7740 10 ай бұрын
Then a higher then optimum will be prefered I guess. Here another problem may arise: your load may be placed at some relatively large distance and you'll have a high transients with ringing on a wire inductance. Then yes - it is more reasonable to to make it as slow as possible.
@RexxSchneider
@RexxSchneider 10 ай бұрын
The problem then becomes the amount of time the mosfet spends in its linear region. If you are sinking a high current with a high voltage supply, you will need to make sure that the power dissipated during the switching is within limits for the device and its heatsink.
@WrittenByMasooma
@WrittenByMasooma Ай бұрын
My gate driver circuit burnt. What could be the reason?
@wisnueepis3593
@wisnueepis3593 5 ай бұрын
is the ringing coming from the parasitic inductance?
@zviper
@zviper 6 ай бұрын
Is there a way without using a o scope?
@patrickvanasbroeck303
@patrickvanasbroeck303 6 ай бұрын
One question remains: how can a small 100ohm resistor make such a difference in connection with the Mohm gate resistance of the mosfet?
MOSFET Gate Drive Resistor Selection - Part 2: Turn Off
7:06
He sees meat everywhere 😄🥩
00:11
AngLova
Рет қаралды 10 МЛН
Did you believe it was real? #tiktok
00:25
Анастасия Тарасова
Рет қаралды 33 МЛН
Was ist im Eis versteckt? 🧊 Coole Winter-Gadgets von Amazon
00:37
SMOL German
Рет қаралды 30 МЛН
БОЛЬШОЙ ПЕТУШОК #shorts
00:21
Паша Осадчий
Рет қаралды 8 МЛН
Snubber Design
10:07
Biricha
Рет қаралды 49 М.
Powerful Knowledge 6 - Gate drive design
1:11:28
Electronic Minds
Рет қаралды 6 М.
Power MOSFET drivers
44:39
Sam Ben-Yaakov
Рет қаралды 251 М.
They Mislead You About MOSFETs
8:54
Lantertronics - Aaron Lanterman
Рет қаралды 66 М.
Input Capacitor Selection for Power Supplies (Part 1)
10:44
3 Simple MOSFET Drive Circuits
12:55
Mr.T's Design Graveyard
Рет қаралды 126 М.
Measuring a MOSFET’s Miller Plateau - Workbench Wednesdays
10:50
element14 presents
Рет қаралды 26 М.
Main filter..
0:15
CikoYt
Рет қаралды 14 МЛН