Most Basic Brushless Motor Control

[@NeoFrontierTechnologies]

You are one of the better electronics channels on youtube. I appreciate your thorough work and decent videos.

[@murraymadness4674]

A half bridge controller is used for a Switched Reluctance Motor or SRM that don't have magnets. If you have magnets, you want full bridge to Push them away, otherwise, they create drag and big inefficiency trying to stick to the un-energized coil. SRM motors are now replacing Induction Motors which don't have magnets either.

[@NiHaoMike64]

My friend Brittany Benzaia used a full bridge design for a switched reluctance centrifugal compressor in a water cycle air conditioner. Apparently, it's worth the complexity to not have the rotor flux reversing which increases iron losses. The compressor spins at over 100k RPM at full power so maybe that doesn't apply for a switched reluctance motor spinning at lower speeds. My guess is that the stator is made of a material with much lower iron losses since it doesn't have to withstand the extreme centrifugal forces the rotor has to.

[@taylorboultinghouse8296]

I love your videos! I am always learning something new. You inspire me to keep pursuing knowledge around electronics. Thank you for sharing!

Wow, amazing content! Now I have to watch the entire playlist on ESCs

[@ELECTRONOOBS]

Thanks! Hope you will like them all!

[@ramadavince6611]

@@ELECTRONOOBS i have done like 5-6 time, and i m thankful that i can build mind now

[@gkdresden]

In this configuration you can also use the back EMF of the open coils for controller synchronization.

[@technicalideas1234]

Exact yestarday i was trying to make such type of an esc for such types of motor Thanks for making my work easy

[@Delali]

This is really cool. Thanks for the tips and lesson. I once taught of building an esc on my channel but I never got around to planning it out. Big ups.

[@BroWorlanyo]

I catch you here now,

[@joshnabours9102]

At 8:40 - you can see that there are voltage spikes on the phases that are off. Wouldn't it be possible to connect high value resistors and use those pulses as a source of back emf feedback?

[@PhG1961]

Excellent video. I really like these series about ESC's and motor control. Thnxs for sharing !

[@myhobbies5965]

Excellent bro. Your esc videos are very informative.

[@saikittang7450]

Would love to see a closed loop foc controller like the vesc and odrive!

[@ELECTRONOOBS]

Working on something like that!

[@Jose-tw9bl]

@@ELECTRONOOBS 🔝🔝🔝

[@elmnaoirfer3751]

¿Se puede utilizar el motor brechless en los ejes utilizados en máquinas cnc (x. y .z) o no ? Gracias

[@tonyotieno8192]

Can't believe this information is free!

[@andrewel5383]

Could you do a video on connecting midgets in parrallel to create higher drain current? I’m working on trying to create a 200-300A ESC

[@JonathanDeWitt1988]

This was another very educational video. Thank you! I learned a lot. Now I need to add the ESC playlist to my watch list.

[@canxinchen5475]

Good job, my motor only has 3 wires, how do I wire Vcc?

[@andremurilobr]

Hi excelent vídeo. Let me know if you have plans to teach how to make ESC for big currents. I need to buy some for 500A or try to do it for myself.

[@Raaddller]

Thanks, very well explained. You've divided the motor into individual poles, neither delta nor wye. Will this controller work for a rewound squirrel cage AC motor; re-wound to handle high amps and low voltage.

[@Inturupter]

Is there a half bridge circuit for delta connected bldc

[@DIYwithBatteries]

I need some time to spend on ESC playlist. Really so curious Dude. 😂👍

[@69iqtutorial]

Iam happy to see a video like this

[@shauncrosby7652]

Just wondering how you would control a 4 wire motor with the full bridge esc, because you say that the common is there on all the motors but just the 3 opposite ends joined, which is fine, but the other esc controllers you showed only had the 3 wires, no 4th connection, and where does the common go in the std motors we typically purchase? And how would you connect the 4 wire to a 3 wire esc? I have tried connecting one to ground then the other phases as normal and still didn't work. So I am wondering how you do it if you recommend a full bridge over the half bridge controller?

[@pratheeps3287]

Can I used this method for hall sensor based motor ?

[@yaseenalrawahi4733]

My favourite channel

[@amirouw]

i got a question master.... im new to these bldcs or esc etc... but how can we say the motor is being drived imean the drivers doing the best and motor is at perfect rotation perfectly via using an osciloscope ???

[@harshitaharshita6543]

Can you make dedicated video on transistor's all configuration

[@pugalstech]

Thanks sir very useful demo I also done the bldc controller with 3 led but it has no starting torque just rotate shaft and than it works perfectly What can I do to improve my controller Pls suggest

[@muhammadsheraz2079]

can you tell about three phase induction motor speed controller

[@botak333]

For half posibl run 3phasa bldc just 3 wire sir??

[@magansoma8549]

Did you implemented zero crosing and communication timing difference by 30 angle in your code i am talking about your full bridge esc Because firing before proper commutation time may leads to more current consumption i am talking about techniques used in avr 444 appnote page 11 .

[@mixalisgeorgantzakos6780]

hi electronobs,how to programng thei attiny85????????

[@marlonglodo1930]

Hi bro is it possible to run 3 or 4 motor in single controller? Thank you

[@kjyhh]

Cool, thanks to use Attiny. Expecting to the full bridge.

[@mubafaw]

Thanks for simplifying 😊👍

[@yodad4776]

Have U got sumthing I can build for my custom RC cars ..I want a simple setup for delta that allows me to have forwards and reverse from vintage radio gear

[@llcd4992]

Hi. Can you make lg direct drive washing machine engine ESC?

[@egongunter6589]

Hallo. Könnte man die Schaltung so ändern dass man einen 220 Volt bldc Motor betreiben kann?

[@Mishnplant]

I have broken my ESC from makita machine but I cant find any replacement for esc . I was waiting for you selling your ESC .i remember you planing to build one you would sell..

[@PaulJosephdeWerk]

Hard drive disk platters can be made of either aluminum, or glass, and are coated with a magnetic material. The last set of drives I tore apart used glass platters and they shattered into sharp shards when I accidentally dropped them on cement.

[@mesquitamk1681]

uma pergunta o motor vai ter a mesmo velocidade e mesma potencoa? com esse modelo e lidaçao estrela a question will the engine have the same speed and the same power? with this model and star deal

[@5minutething519]

Is the ESC control same for axial flux and radial flux BLDC ?

[@shubhranshushekharpradhan8689]

Please make half mosfet for drone bldc motor

[@AJB2K3]

Nice work. You've now done delta motors and Star motors. Track down a Star/Delta motor and try controlling them? I know these will be hard to find as they are old hat now.

[@youshamasood4018]

Can you create all in one arduino rc receiver circuit(4 escs, power distribution, and rc receiver) with just one microcontroller

[@kingphilip7144]

How to change direction or make just in on direction?

[@ashraf9472]

الله ينور عليك يا هندسة

[@andreiciora2765]

Hristos a înviat

[@MrMic18650]

What is the value of the potentialometer

[@RandomRandom-j7g]

The best Video. 🏅🏅🏅🏅🏅

[@martinsiolowosoran5242]

Please i need your assistance. I use ir2104 but the high side is not switching, please what can i do

[@electronic7979]

Helpful information

[@roastingtvindian6852]

Nice dude 2 nd commment love you video form India

[@ELECTRONOOBS]

Thank you!

[@lordjaashin]

who cares where you're from? just give a compliment for his video and move on

[@nemesys295]

Good work, nice👍

[@gyrgrls]

Does that hard drive acutator read fingerprints, too?

[@Jerome____]

Can you please do an diy ebike esc?

[@ParsMaker]

nice work, it would be great to make a video about how to calculate BLM amp rating and kv

[@lpt2606]

Esc are the best things ever.

[@boratrilha]

I need to build an esc that supports 20A to use with a 28V 3-phase motor. Does anyone know of a project with this capability?

[@PAK_MARINE]

Hi how are u I need full bldc motor explanation with hall sensor how to run with 6 mosfet

[@fajarefendi2444]

Aku ingin sedikit bertanya...kenapa sebuah pengiling sudut motor brushles 18volt dc tidak bisa bekerja bila di beri 25 volt dc??

[@shubhranshushekharpradhan8689]

Please test on bldc

[@SakellarisNikolaos]

Thank you 😊

[@winkus8586]

Do you know the max rpm it can reach using the hdd motor? Thanks

[@AsBi1]

very helpful videos. i love it

[@andrewel5383]

Does a half bridge give only half the amount of power vs a full bridge? Also does this circuit allow to go full speed?

[@boasnovasonline8764]

could the friend do a video assembling an esc 'for automotive alternator?

[@kesor6]

Can something like this be made using L293D instead of mosfets?

[@trinityinc877]

Hi Sir, My name is Anand, Please tell me Instead of half bridge configuration, can we use full bridge configuration? and what difference will get in both configuration?

[@sanstory1284]

How many amperes can you use with this esc bro? please answer 🙏🏻

[@lis6502]

Thanks for deep diving while still floating and not drowning xD

[@kekekeernest8920]

Please, can you make a video on building a simple SMPS circuit, with the basic understanding, because I really don't understand the what components, schematic to use.

[@Dancopymus]

Hello teacher! Firstly, thanks for sharing. What is the difference between your circuit (half bridge), which uses Arduino, and the others shown on the internet but which do not use Arduino? Another thing: instead of the AMS1117, can the LM7805 be used? P.S.: And if I'm not asking too much, is it possible to have a connection schematic that's a little clearer to understand? Thanks++

[@edilsonalvesdasilva5617]

It's amazing, congratulation.

[@RixtronixLAB]

Nice info, thanks for sharing :)

[@ReptarKingoftheBrozone]

A long time ago you made a video about an arduino based temperature controller using a PID loop. I was curious if the diode set up that you used to step down from 220V to 5V is a safe method to be run 24/7? If not, then what is the safest method for 110V step down to 5V for sustained “power-on” use?

[@harikamalakarreddydarapu7410]

Awesome project

[@انوالعراقي-غ9ر]

Nice work

[@anandmohan6412]

Wow nice one

[@GnuReligion]

The PWM frequency is rather slow by default when using AVR8 chips through Arduino, tending to cause an audible buzz and vibration. // You could use something like this for the t85: TCCR0B = TCCR0B & 0b11111000 | 0b001; // 32.35kHz

[@orgazmi]

Hi I need speed cintiriel 3 phase DC, 12-120v +- 40-50a. +- 1500w can you help.me craft it ?

[@OMNI_INFINITY]

Thanks! Recommend more ORDER on that board though. ORDERLY component layouts say "professional".

[@EasyOne]

Very useful video

[@ericburger5337]

Thanks you very much for those explications , it is very useful..

[@0120-b2l]

Well done . Thanks

[@robertolins7942]

Amigo passa o diagrama eletrico e contagem

[@bhargavsinghaxiscienceb4380]

pls make video on arduino nano PWM drone esc calliberation very soon as possible

[@MrMic18650]

Can you make a L298N motor driver.

[@antoniogalindo3459]

The Esc circuit to delta configuration thank you

[@Dragon-rv4xr]

Ne555 working ?

[@daviddelatorreperez4]

Has un esc con el mc333035

[@khursheedhazarvi]

Great information

[@rinokentie8653]

Very useful!

[@AJB2K3]

Is FASE a typo or how it is spelt in your normal language?

[@jackwilliams2010]

Nice video! Are half bridges more efficient than full bridges? From an energy usage perspective. If it is both simpler and more efficient, then it sounds like the hall effect sensor might be the only major downside.

[@dientu97]

Có file nguyên lý với code không ad? Cho mình xin với. Thanks!

[@armandorodriguez6843]

I like to learn more about technological electronics

[@sudheerkumar5966]

Very good sir

[@shantotorofder3916]

Hey plz make something f4 flight controller with 4 in 1esc...with arduino and mpu........... 4 esc with flight controller board now most demanding.to make fpv drone............. so plz make something like that........ and plz tell me that arduino nrf ppm receiver can use in any flight controller which support ppm signal

[@sachinmestry6385]

Do you have Brush Motor ESC without Programming ?

[@ELECTRONOOBS]

No I don't have that and I'm not sure if that is possible. With ICs directly?

[@danriches7328]

Rather than change the software to handle PWM just add an RC filter to the input and you get an analog voltage so 2 components will eliminate having to change working software ;)