Рет қаралды 4,840
What does running-in an engine mean and is it necessary?
Ask ten people what is the best way and why to run-in the engine and you are likely to get ten different answers.
This is because there is a huge amount of confusion and a huge amount of information all over the internet arguing and justifying different approaches.
In my opinion most of the information is outdated, because most of the information and techniques have come from our grandfather times!
Today I will share my thoughts on this subject and how I go about running-in my new motorcycles.
First things first, you need to know what you’re doing when “running-in” a new engine.
Some people think we are trying to bed-in the bearings, the crankshaft, the gears and the clutch plates and so on, and that is not the case at all.
The only component that is actually being run-in is the piston rings. We are trying to bed those rings so that they achieve a correct seal against the cylinder walls.
And we have a very small window to do this. About 50 kms or an hour at most.
Taking too long and being too gentle will not help bed in the rings to the cylinder.
The honing would have gone by then and so will the chance to bed the piston rings to the cylinder walls. It is an irreversible process.
The worst thing you can do while breaking in an engine is taking care of the engine like a baby by allowing it to idle for extended periods and by riding it ever so slowly and too gently.
This will place almost no load on the rings and the bedding process can fail.
Note, it is the violent, hard and high temperature combustion that gets the piston rings to expand, press and seal against the cylinder walls, not gentle operations.
I know quite a few riders who believe that they better err on the slow side than err on the fast side and end up babying the engine for a 1000s of kms!
This is more damaging that revving the hell out of the engine when it is new.
In fact revving the hell out of the engine does not cause any damage to a modern motorcycle engine.
There have been tests conducted on two identical engines where one of the engines was run-in using the slow step by step process as recommended by the manufacturer and the other engine was run at higher speeds including full throttle right from the start.
Ari Henning and his team at Motorcyclist Online had conducted such a running-in test on a Honda 300cc engine.
Unsurprisingly, to me, the results are that there was no difference in compression or performance or clearances in any of the components between the two engines post the tests.
Every parameter was exactly the same.
To me, the idea of the long and step by step running in is very old and outdated and not necessary anymore.
Manufacturers give these steps are just to ensure that if something were to break in the engine, one, it would be less dangerous if it broke at 3000 rpm instead of at 9000 rpm and two, the collateral damage within the engine would be less. That’s all!!
Believe me, once the first 50 kms is done on a new motorcycle, every km done from there is only more wear and tear and nothing actually improves.
There is no more bedding in or running in that is going to happen after that.
Routine wear and tear starts taking its course and the engine is only getting older from that moment onwards.
Modern engine technology is advanced enough to be able to hand all kinds of abuse.
Tolerances and metallurgy have come a long way since the cast-iron Royal Enfield Bullet and Yezdi 250 days and since the Ambassador and Premier Padmini days.
Gaskets have improved, oils have improved, metals and alloys have improved, machining has improved, tolerances have improved and designs have improved.
The main focus area, piston rings and cylinder walls are now designed and manufactured with a much more advanced honing pattern that beds in within the first 50 kms if ridden freely.
So, the bottom line is do not worry or stress too much about running in because whatever you do is not going to make any perceptible difference anyway.
Take the middle ground. Don’t be too slow and ride 1000s of kms running-in the engine and also don’t be rash and reckless and push the new engine to full throttle and rev-limiter right away.
Start the engine, warm it up for just a minute or two max and get riding.
Ride the motorcycle as you normally would and that will be good enough.
Enjoy the motorcycle and most importantly no matter how you ride, ensure regular oil changes as per owner’s manual.
Hope you enjoyed this video. Let me know what you think about running in.
Cheers!
#artofunwinding #bigbearbangalore #motorcycles #enginerunin #enginebreakgin #motorcycleadvice #engineoil #ducatimultistrada #norway #edelweissbike
/ artofunwinding